| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
|
|
|
|
|
|
There is code in ssb fetching "invariants" that is basically a set of
board specific data. Every host requires its own implementation of
reading function. In ssb we have support for PCI, PCMCIA & SDIO.
For some (historical?) reason code reading "invariants" for SoC was
placed in arch code and provided by a callback. This is not needed
nowadays, so lets move that into ssb. This way we keep all "invariants"
functions in a single module making code cleaner.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Major changes:
ath9k
* add random number generator support (CONFIG_ATH9K_HWRNG)
|
|
An AP can send an operating channel width change in a beacon
opmode notification IE as long as there's a change in the nss as
well (See 802.11ac-2013 section 10.41).
So don't limit updating to nss only from an opmode notification IE.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the AP is advertising limited TX power, the message can be
printed over and over again. Suppress it when the power level
isn't changing.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=106011
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
During reprogramming, mac80211 currently first adds all the channel
contexts, then binds them to the vifs and then goes to reconfigure
all the interfaces. Drivers might, perhaps implicitly, rely on the
operation order for certain things that typically happen within a
single function elsewhere in mac80211. To avoid problems with that,
reorder the code in mac80211's restart/reprogramming to work fully
within the interface loop so that the order of operations is like
in normal operation.
For iwlwifi, this fixes a firmware crash when reprogramming with an
AP/GO interface active.
Reported-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When reconfiguration during resume fails while a scan is pending
for completion work, that work will never run, and the scan will
be stuck forever. Factor out the code to recover this and call it
also in ieee80211_handle_reconfig_failure().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Free cached keys if the last early return path is taken.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Compared to cfg80211_rdev_free_wowlan in core.h,
the error goto label lacks the freeing of nd_config.
Fix that.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The first leak occurs when entering the default case
in the switch for the initiator in set_regdom.
The second leaks a platform_device struct if the
platform registration in regulatory_init succeeds but
the sub sequent regulatory hint fails due to no memory.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux
|
|
Mesh Point requires peer security key install when running
in secured mode since it's a type of peer links, otherwise peer
link will be removed due to key install failure.
MFP feature set is required to run Mesh in secured mode and
QCA988X firmware, 10.2.4.70.14-2 and above, is the only one
supporting secured Mesh at this moment.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
|
|
Jan Stancek reported that I wrecked things for him by fixing things for
Vladimir :/
His report was due to an UNINTERRUPTIBLE wait getting -EINTR, which
should not be possible, however my previous patch made this possible by
unconditionally checking signal_pending().
We cannot use current->state as was done previously, because the
instruction after the store to that variable it can be changed. We must
instead pass the initial state along and use that.
Fixes: 68985633bccb ("sched/wait: Fix signal handling in bit wait helpers")
Reported-by: Jan Stancek <jstancek@redhat.com>
Reported-by: Chris Mason <clm@fb.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Chris Mason <clm@fb.com>
Reviewed-by: Paul Turner <pjt@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: tglx@linutronix.de
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull NFS client bugfix from Trond Myklebust:
"SUNRPC: Fix a NFSv4.1 callback channel regression"
* tag 'nfs-for-4.4-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Fix callback channel
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixlets from Thomas Gleixner:
"Two trivial fixes which add missing header fileas and forward
declarations so the code will compile even when the magic include
chains are different"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Add missing include for barrier.h
irqchip/gic-v3: Add missing struct device_node declaration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix to unbreak a clocksource driver which has more than 32bit
counter width"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Mmio: remove artificial 32bit limitation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull fpga driver fixes from Greg KH:
"Only two small fpga driver fixes here, both have been in linux-next
for a while, and resolve some reported issues"
* tag 'char-misc-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
fpga manager: Fix firmware resource leak on error
fpga manager: remove label
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few staging and IIO driver fixes for 4.4-rc5.
All of them resolve reported problems and have been in linux-next for
a while. Nothing major here, just small fixes where needed"
* tag 'staging-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: lustre: echo_copy.._lsm() dereferences userland pointers directly
iio: adc: spmi-vadc: add missing of_node_put
iio: fix some warning messages
iio: light: apds9960: correct ->last_busy count
iio: lidar: return -EINVAL on invalid signal
staging: iio: dummy: complete IIO events delivery to userspace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are a number of small USB fixes for 4.4-rc5. All of them have
been in linux-next. The majority are gadget and phy issues, with a
few new quirks and device ids added as well"
* tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (32 commits)
USB: add quirk for devices with broken LPM
xhci: fix usb2 resume timing and races.
usb: musb: fail with error when no DMA controller set
usb: gadget: uvc: fix permissions of configfs attributes
usb: musb: core: Fix pm runtime for deferred probe
usb: phy: msm: fix a possible NULL dereference
USB: host: ohci-at91: fix a crash in ohci_hcd_at91_overcurrent_irq
usb: Quiet down false peer failure messages
usb: xhci: fix config fail of FS hub behind a HS hub with MTT
xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()
usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message
USB: whci-hcd: add check for dma mapping error
usb: core : hub: Fix BOS 'NULL pointer' kernel panic
USB: quirks: Apply ALWAYS_POLL to all ELAN devices
usb-storage: Fix scsi-sd failure "Invalid field in cdb" for USB adapter JMicron
USB: quirks: Fix another ELAN touchscreen
usb: dwc3: gadget: don't prestart interrupt endpoints
USB: serial: Another Infineon flash loader USB ID
USB: cdc_acm: Ignore Infineon Flash Loader utility
USB: cp210x: Remove CP2110 ID from compatibility list
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- opal-irqchip: Fix double endian conversion from Alistair Popple
- cxl: Set endianess of kernel contexts from Frederic Barrat
- sbc8641: drop bogus PHY IRQ entries from DTS file from Paul Gortmaker
- Revert "powerpc/eeh: Don't unfreeze PHB PE after reset" from Andrew
Donnellan
* tag 'powerpc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
Revert "powerpc/eeh: Don't unfreeze PHB PE after reset"
powerpc/sbc8641: drop bogus PHY IRQ entries from DTS file
cxl: Set endianess of kernel contexts
powerpc/opal-irqchip: Fix double endian conversion
|
|
Merge misc fixes from Andrew Morton:
"17 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MIPS: fix DMA contiguous allocation
sh64: fix __NR_fgetxattr
ocfs2: fix SGID not inherited issue
mm/oom_kill.c: avoid attempting to kill init sharing same memory
drivers/base/memory.c: prohibit offlining of memory blocks with missing sections
tmpfs: fix shmem_evict_inode() warnings on i_blocks
mm/hugetlb.c: fix resv map memory leak for placeholder entries
mm: hugetlb: call huge_pte_alloc() only if ptep is null
kernel: remove stop_machine() Kconfig dependency
mm: kmemleak: mark kmemleak_init prototype as __init
mm: fix kerneldoc on mem_cgroup_replace_page
osd fs: __r4w_get_page rely on PageUptodate for uptodate
MAINTAINERS: make Vladimir co-maintainer of the memory controller
mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress
mm: fix swapped Movable and Reclaimable in /proc/pagetypeinfo
memcg: fix memory.high target
mm: hugetlb: fix hugepage memory leak caused by wrong reserve count
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Fix the boot crash on Mako machines with Huge Pages, prevent a panic
with SATA controllers (and others) by correctly calculating the IOMMU
space, hook up the mlock2 syscall and drop unneeded code in the parisc
pci code"
* 'parisc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Disable huge pages on Mako machines
parisc: Wire up mlock2 syscall
parisc: Remove unused pcibios_init_bus()
parisc iommu: fix panic due to trying to allocate too large region
|
|
Pull block layer fixes from Jens Axboe:
"A set of fixes for the current series. This contains:
- A bunch of fixes for lightnvm, should be the last round for this
series. From Matias and Wenwei.
- A writeback detach inode fix from Ilya, also marked for stable.
- A block (though it says SCSI) fix for an OOPS in SCSI runtime power
management.
- Module init error path fixes for null_blk from Minfei"
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: Fix error path in module initialization
lightnvm: do not compile in debugging by default
lightnvm: prevent gennvm module unload on use
lightnvm: fix media mgr registration
lightnvm: replace req queue with nvmdev for lld
lightnvm: comments on constants
lightnvm: check mm before use
lightnvm: refactor spin_unlock in gennvm_get_blk
lightnvm: put blks when luns configure failed
lightnvm: use flags in rrpc_get_blk
block: detach bdev inode from its wb in __blkdev_put()
SCSI: Fix NULL pointer dereference in runtime PM
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Update the linker script to use L1_CACHE_BYTES instead of hard-coded
64. We recently changed L1_CACHE_BYTES to 128
- Improve race condition reporting on set_pte_at() and change the BUG
to WARN_ONCE. With hardware update of the accessed/dirty state, we
need to ensure that set_pte_at() does not inadvertently override
hardware updated state. The patch also makes the checks ignore
!pte_valid() new entries
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Improve error reporting on set_pte_at() checks
arm64: update linker script to increased L1_CACHE_BYTES value
|
|
Recent changes to how GFP_ATOMIC is defined seems to have broken the
condition to use mips_alloc_from_contiguous() in
mips_dma_alloc_coherent().
I couldn't bottom out the exact change but I think it's this commit
d0164adc89f6 ("mm, page_alloc: distinguish between being unable to
sleep, unwilling to sleep and avoiding waking kswapd").
GFP_ATOMIC has multiple bits set and the check for !(gfp & GFP_ATOMIC)
isn't enough.
The reason behind this condition is to check whether we can potentially
do a sleeping memory allocation. Use gfpflags_allow_blocking() instead
which should be more robust.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
According to arch/sh/kernel/syscalls_64.S and common sense, __NR_fgetxattr
has to be defined to 259, but it doesn't. Instead, it's defined to 269,
which is of course used by another syscall, __NR_sched_setaffinity in this
case.
This bug was found by strace test suite.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 8f1eb48758aa ("ocfs2: fix umask ignored issue") introduced an
issue, SGID of sub dir was not inherited from its parents dir. It is
because SGID is set into "inode->i_mode" in ocfs2_get_init_inode(), but
is overwritten by "mode" which don't have SGID set later.
Fixes: 8f1eb48758aa ("ocfs2: fix umask ignored issue")
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It's possible that an oom killed victim shares an ->mm with the init
process and thus oom_kill_process() would end up trying to kill init as
well.
This has been shown in practice:
Out of memory: Kill process 9134 (init) score 3 or sacrifice child
Killed process 9134 (init) total-vm:1868kB, anon-rss:84kB, file-rss:572kB
Kill process 1 (init) sharing same memory
...
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
And this will result in a kernel panic.
If a process is forked by init and selected for oom kill while still
sharing init_mm, then it's likely this system is in a recoverable state.
However, it's better not to try to kill init and allow the machine to
panic due to unkillable processes.
[rientjes@google.com: rewrote changelog]
[akpm@linux-foundation.org: fix inverted test, per Ben]
Signed-off-by: Chen Jie <chenjie6@huawei.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Li Zefan <lizefan@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit bdee237c0343 ("x86: mm: Use 2GB memory block size on large-memory
x86-64 systems") and 982792c782ef ("x86, mm: probe memory block size for
generic x86 64bit") introduced large block sizes for x86. This made it
possible to have multiple sections per memory block where previously,
there was a only every one section per block.
Since blocks consist of contiguous ranges of section, there can be holes
in the blocks where sections are not present. If one attempts to
offline such a block, a crash occurs since the code is not designed to
deal with this.
This patch is a quick fix to gaurd against the crash by not allowing
blocks with non-present sections to be offlined.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=107781
Signed-off-by: Seth Jennings <sjennings@variantweb.net>
Reported-by: Andrew Banman <abanman@sgi.com>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Dmitry Vyukov provides a little program, autogenerated by syzkaller,
which races a fault on a mapping of a sparse memfd object, against
truncation of that object below the fault address: run repeatedly for a
few minutes, it reliably generates shmem_evict_inode()'s
WARN_ON(inode->i_blocks).
(But there's nothing specific to memfd here, nor to the fstat which it
happened to use to generate the fault: though that looked suspicious,
since a shmem_recalc_inode() had been added there recently. The same
problem can be reproduced with open+unlink in place of memfd_create, and
with fstatfs in place of fstat.)
v3.7 commit 0f3c42f522dc ("tmpfs: change final i_blocks BUG to WARNING")
explains one cause of such a warning (a race with shmem_writepage to
swap), and possible solutions; but we never took it further, and this
syzkaller incident turns out to have a different cause.
shmem_getpage_gfp()'s error recovery, when a freshly allocated page is
then found to be beyond eof, looks plausible - decrementing the alloced
count that was just before incremented - but in fact can go wrong, if a
racing thread (the truncator, for example) gets its shmem_recalc_inode()
in just after our delete_from_page_cache(). delete_from_page_cache()
decrements nrpages, that shmem_recalc_inode() will balance the books by
decrementing alloced itself, then our decrement of alloced take it one
too low: leading to the WARNING when the object is finally evicted.
Once the new page has been exposed in the page cache,
shmem_getpage_gfp() must leave it to shmem_recalc_inode() itself to get
the accounting right in all cases (and not fall through from "trunc:" to
"decused:"). Adjust that error recovery block; and the reinitialization
of info and sbinfo can be removed too.
While we're here, fix shmem_writepage() to avoid the original issue: it
will be safe against a racing shmem_recalc_inode(), if it merely
increments swapped before the shmem_delete_from_page_cache() which
decrements nrpages (but it must then do its own shmem_recalc_inode()
before that, while still in balance, instead of after). (Aside: why do
we shmem_recalc_inode() here in the swap path? Because its raison d'etre
is to cope with clean sparse shmem pages being reclaimed behind our
back: so here when swapping is a good place to look for that case.) But
I've not now managed to reproduce this bug, even without the patch.
I don't see why I didn't do that earlier: perhaps inhibited by the
preference to eliminate shmem_recalc_inode() altogether. Driven by this
incident, I do now have a patch to do so at last; but still want to sit
on it for a bit, there's a couple of questions yet to be resolved.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Dmitry Vyukov reported the following memory leak
unreferenced object 0xffff88002eaafd88 (size 32):
comm "a.out", pid 5063, jiffies 4295774645 (age 15.810s)
hex dump (first 32 bytes):
28 e9 4e 63 00 88 ff ff 28 e9 4e 63 00 88 ff ff (.Nc....(.Nc....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
kmalloc include/linux/slab.h:458
region_chg+0x2d4/0x6b0 mm/hugetlb.c:398
__vma_reservation_common+0x2c3/0x390 mm/hugetlb.c:1791
vma_needs_reservation mm/hugetlb.c:1813
alloc_huge_page+0x19e/0xc70 mm/hugetlb.c:1845
hugetlb_no_page mm/hugetlb.c:3543
hugetlb_fault+0x7a1/0x1250 mm/hugetlb.c:3717
follow_hugetlb_page+0x339/0xc70 mm/hugetlb.c:3880
__get_user_pages+0x542/0xf30 mm/gup.c:497
populate_vma_page_range+0xde/0x110 mm/gup.c:919
__mm_populate+0x1c7/0x310 mm/gup.c:969
do_mlock+0x291/0x360 mm/mlock.c:637
SYSC_mlock2 mm/mlock.c:658
SyS_mlock2+0x4b/0x70 mm/mlock.c:648
Dmitry identified a potential memory leak in the routine region_chg,
where a region descriptor is not free'ed on an error path.
However, the root cause for the above memory leak resides in region_del.
In this specific case, a "placeholder" entry is created in region_chg.
The associated page allocation fails, and the placeholder entry is left
in the reserve map. This is "by design" as the entry should be deleted
when the map is released. The bug is in the region_del routine which is
used to delete entries within a specific range (and when the map is
released). region_del did not handle the case where a placeholder entry
exactly matched the start of the range range to be deleted. In this
case, the entry would not be deleted and leaked. The fix is to take
these special placeholder entries into account in region_del.
The region_chg error path leak is also fixed.
Fixes: feba16e25a57 ("mm/hugetlb: add region_del() to delete a specific range of entries")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org> [4.3+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently at the beginning of hugetlb_fault(), we call huge_pte_offset()
and check whether the obtained *ptep is a migration/hwpoison entry or
not. And if not, then we get to call huge_pte_alloc(). This is racy
because the *ptep could turn into migration/hwpoison entry after the
huge_pte_offset() check. This race results in BUG_ON in
huge_pte_alloc().
We don't have to call huge_pte_alloc() when the huge_pte_offset()
returns non-NULL, so let's fix this bug with moving the code into else
block.
Note that the *ptep could turn into a migration/hwpoison entry after
this block, but that's not a problem because we have another
!pte_present check later (we never go into hugetlb_no_page() in that
case.)
Fixes: 290408d4a250 ("hugetlb: hugepage migration core")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: <stable@vger.kernel.org> [2.6.36+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently the full stop_machine() routine is only enabled on SMP if
module unloading is enabled, or if the CPUs are hotpluggable. This
leads to configurations where stop_machine() is broken as it will then
only run the callback on the local CPU with irqs disabled, and not stop
the other CPUs or run the callback on them.
For example, this breaks MTRR setup on x86 in certain configs since
ea8596bb2d8d379 ("kprobes/x86: Remove unused text_poke_smp() and
text_poke_smp_batch() functions") as the MTRR is only established on the
boot CPU.
This patch removes the Kconfig option for STOP_MACHINE and uses the SMP
and HOTPLUG_CPU config options to compile the correct stop_machine() for
the architecture, removing the false dependency on MODULE_UNLOAD in the
process.
Link: https://lkml.org/lkml/2014/10/8/124
References: https://bugs.freedesktop.org/show_bug.cgi?id=84794
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Pranith Kumar <bobby.prani@gmail.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Iulia Manda <iulia.manda21@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chuck Ebbert <cebbert.lkml@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The kmemleak_init() definition in mm/kmemleak.c is marked __init but its
prototype in include/linux/kmemleak.h is marked __ref since commit
a6186d89c913 ("kmemleak: Mark the early log buffer as __initdata").
This causes a section mismatch which is reported as a warning when
building with clang -Wsection, because kmemleak_init() is declared in
section .ref.text but defined in .init.text.
Fix this by marking kmemleak_init() prototype __init.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Whoops, I missed removing the kerneldoc comment of the lrucare arg
removed from mem_cgroup_replace_page; but it's a good comment, keep it.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 42cb14b110a5 ("mm: migrate dirty page without
clear_page_dirty_for_io etc") simplified the migration of a PageDirty
pagecache page: one stat needs moving from zone to zone and that's about
all.
It's convenient and safest for it to shift the PageDirty bit from old
page to new, just before updating the zone stats: before copying data
and marking the new PageUptodate. This is all done while both pages are
isolated and locked, just as before; and just as before, there's a
moment when the new page is visible in the radix_tree, but not yet
PageUptodate. What's new is that it may now be briefly visible as
PageDirty before it is PageUptodate.
When I scoured the tree to see if this could cause a problem anywhere,
the only places I found were in two similar functions __r4w_get_page():
which look up a page with find_get_page() (not using page lock), then
claim it's uptodate if it's PageDirty or PageWriteback or PageUptodate.
I'm not sure whether that was right before, but now it might be wrong
(on rare occasions): only claim the page is uptodate if PageUptodate.
Or perhaps the page in question could never be migratable anyway?
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Boaz Harrosh <ooo@electrozaur.com>
Cc: Benny Halevy <bhalevy@panasas.com>
Cc: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Vladimir architected and authored much of the current state of the
memcg's slab memory accounting and tracking. Make sure he gets CC'd on
bug reports ;-)
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
progress
Tetsuo Handa has reported that the system might basically livelock in
OOM condition without triggering the OOM killer.
The issue is caused by internal dependency of the direct reclaim on
vmstat counter updates (via zone_reclaimable) which are performed from
the workqueue context. If all the current workers get assigned to an
allocation request, though, they will be looping inside the allocator
trying to reclaim memory but zone_reclaimable can see stalled numbers so
it will consider a zone reclaimable even though it has been scanned way
too much. WQ concurrency logic will not consider this situation as a
congested workqueue because it relies that worker would have to sleep in
such a situation. This also means that it doesn't try to spawn new
workers or invoke the rescuer thread if the one is assigned to the
queue.
In order to fix this issue we need to do two things. First we have to
let wq concurrency code know that we are in trouble so we have to do a
short sleep. In order to prevent from issues handled by 0e093d99763e
("writeback: do not sleep on the congestion queue if there are no
congested BDIs or if significant congestion is not being encountered in
the current zone") we limit the sleep only to worker threads which are
the ones of the interest anyway.
The second thing to do is to create a dedicated workqueue for vmstat and
mark it WQ_MEM_RECLAIM to note it participates in the reclaim and to
have a spare worker thread for it.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Tejun Heo <tj@kernel.org>
Cc: Cristopher Lameter <clameter@sgi.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Arkadiusz Miskiewicz <arekm@maven.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 016c13daa5c9 ("mm, page_alloc: use masks and shifts when
converting GFP flags to migrate types") has swapped MIGRATE_MOVABLE and
MIGRATE_RECLAIMABLE in the enum definition. However, migratetype_names
wasn't updated to reflect that.
As a result, the file /proc/pagetypeinfo shows the counts for Movable as
Reclaimable and vice versa.
Additionally, commit 0aaa29a56e4f ("mm, page_alloc: reserve pageblocks
for high-order atomic allocations on demand") introduced
MIGRATE_HIGHATOMIC, but did not add a letter to distinguish it into
show_migration_types(), so it doesn't appear in the listing of free
areas during page alloc failures or oom kills.
This patch fixes both problems. The atomic reserves will show with a
letter 'H' in the free areas listings.
Fixes: 016c13daa5c9 ("mm, page_alloc: use masks and shifts when converting GFP flags to migrate types")
Fixes: 0aaa29a56e4f ("mm, page_alloc: reserve pageblocks for high-order atomic allocations on demand")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the memory.high threshold is exceeded, try_charge() schedules a
task_work to reclaim the excess. The reclaim target is set to the
number of pages requested by try_charge().
This is wrong, because try_charge() usually charges more pages than
requested (batch > nr_pages) in order to refill per cpu stocks. As a
result, a process in a cgroup can easily exceed memory.high
significantly when doing a lot of charges w/o returning to userspace
(e.g. reading a file in big chunks).
Fix this issue by assuring that when exceeding memory.high a process
reclaims as many pages as were actually charged (i.e. batch).
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When dequeue_huge_page_vma() in alloc_huge_page() fails, we fall back on
alloc_buddy_huge_page() to directly create a hugepage from the buddy
allocator.
In that case, however, if alloc_buddy_huge_page() succeeds we don't
decrement h->resv_huge_pages, which means that successful
hugetlb_fault() returns without releasing the reserve count. As a
result, subsequent hugetlb_fault() might fail despite that there are
still free hugepages.
This patch simply adds decrementing code on that code path.
I reproduced this problem when testing v4.3 kernel in the following situation:
- the test machine/VM is a NUMA system,
- hugepage overcommiting is enabled,
- most of hugepages are allocated and there's only one free hugepage
which is on node 0 (for example),
- another program, which calls set_mempolicy(MPOL_BIND) to bind itself to
node 1, tries to allocate a hugepage,
- the allocation should fail but the reserve count is still hold.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: <stable@vger.kernel.org> [3.16+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Mako-based machines (PA8800 and PA8900 CPUs) don't allow aliasing on
non-equaivalent addresses.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
There are no callers of pcibios_init_bus(), so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
When using the Promise TX2+ SATA controller on PA-RISC, the system often
crashes with kernel panic, for example just writing data with the dd
utility will make it crash.
Kernel panic - not syncing: drivers/parisc/sba_iommu.c: I/O MMU @ 000000000000a000 is out of mapping resources
CPU: 0 PID: 18442 Comm: mkspadfs Not tainted 4.4.0-rc2 #2
Backtrace:
[<000000004021497c>] show_stack+0x14/0x20
[<0000000040410bf0>] dump_stack+0x88/0x100
[<000000004023978c>] panic+0x124/0x360
[<0000000040452c18>] sba_alloc_range+0x698/0x6a0
[<0000000040453150>] sba_map_sg+0x260/0x5b8
[<000000000c18dbb4>] ata_qc_issue+0x264/0x4a8 [libata]
[<000000000c19535c>] ata_scsi_translate+0xe4/0x220 [libata]
[<000000000c19a93c>] ata_scsi_queuecmd+0xbc/0x320 [libata]
[<0000000040499bbc>] scsi_dispatch_cmd+0xfc/0x130
[<000000004049da34>] scsi_request_fn+0x6e4/0x970
[<00000000403e95a8>] __blk_run_queue+0x40/0x60
[<00000000403e9d8c>] blk_run_queue+0x3c/0x68
[<000000004049a534>] scsi_run_queue+0x2a4/0x360
[<000000004049be68>] scsi_end_request+0x1a8/0x238
[<000000004049de84>] scsi_io_completion+0xfc/0x688
[<0000000040493c74>] scsi_finish_command+0x17c/0x1d0
The cause of the crash is not exhaustion of the IOMMU space, there is
plenty of free pages. The function sba_alloc_range is called with size
0x11000, thus the pages_needed variable is 0x11. The function
sba_search_bitmap is called with bits_wanted 0x11 and boundary size is
0x10 (because dma_get_seg_boundary(dev) returns 0xffff).
The function sba_search_bitmap attempts to allocate 17 pages that must not
cross 16-page boundary - it can't satisfy this requirement
(iommu_is_span_boundary always returns true) and fails even if there are
many free entries in the IOMMU space.
How did it happen that we try to allocate 17 pages that don't cross
16-page boundary? The cause is in the function iommu_coalesce_chunks. This
function tries to coalesce adjacent entries in the scatterlist. The
function does several checks if it may coalesce one entry with the next,
one of those checks is this:
if (startsg->length + dma_len > max_seg_size)
break;
When it finishes coalescing adjacent entries, it allocates the mapping:
sg_dma_len(contig_sg) = dma_len;
dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
sg_dma_address(contig_sg) =
PIDE_FLAG
| (iommu_alloc_range(ioc, dev, dma_len) << IOVP_SHIFT)
| dma_offset;
It is possible that (startsg->length + dma_len > max_seg_size) is false
(we are just near the 0x10000 max_seg_size boundary), so the funcion
decides to coalesce this entry with the next entry. When the coalescing
succeeds, the function performs
dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
And now, because of non-zero dma_offset, dma_len is greater than 0x10000.
iommu_alloc_range (a pointer to sba_alloc_range) is called and it attempts
to allocate 17 pages for a device that must not cross 16-page boundary.
To fix the bug, we must make sure that dma_len after addition of
dma_offset and alignment doesn't cross the segment boundary. I.e. change
if (startsg->length + dma_len > max_seg_size)
break;
to
if (ALIGN(dma_len + dma_offset + startsg->length, IOVP_SIZE) > max_seg_size)
break;
This patch makes this change (it precalculates max_seg_boundary at the
beginning of the function iommu_coalesce_chunks). I also added a check
that the mapping length doesn't exceed dma_get_seg_boundary(dev) (it is
not needed for Promise TX2+ SATA, but it may be needed for other devices
that have dma_get_seg_boundary lower than dma_get_max_seg_size).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 4.4, 2nd round" from Shawn Guo:
The i.MX fixes for 4.4, 2nd round:
- Fix vf610 SAI clock configuration bug which is discovered by the newly
added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
* tag 'imx-fixes-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
|
|
The GPIO block for ls2080a platform has little endian registers,
the GPIO driver needs this property to read/write registers by
right interface.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
The GPIO block on different QorIQ chips could have registers in different
endianess. Define the property to specify which endian is used by the
hardware.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Add the "little-endian" property to fix the issue that eSDHC
is not working and dumping out "mmc0: Controller never released
inhibit bit(s)." error messages constantly.
Fixes: 5461597f6ce0 ("dts/ls2080a: Update DTSI to add support of various peripherals")
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Cc: stable <stable@vger.kernel.org>
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Five stable fixes:
- Two DM btree bufio buffer leak fixes that resolve reported BUG_ONs
during DM thinp metadata close's dm_bufio_client_destroy().
- A DM thinp range discard fix to handle discarding a partially
mapped range.
- A DM thinp metadata snapshot fix to make sure the btree roots saved
in the metadata snapshot are the most current.
- A DM space map metadata refcounting fix that improves both DM thinp
and DM cache metadata"
* tag 'dm-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm btree: fix bufio buffer leaks in dm_btree_del() error path
dm space map metadata: fix ref counting bug when bootstrapping a new space map
dm thin metadata: fix bug when taking a metadata snapshot
dm thin metadata: fix bug in dm_thin_remove_range()
dm btree: fix leak of bufio-backed block in btree_split_sibling error path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"Two bugfixes, both bound for -stable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: break infinite loop in fuse_fill_write_pages()
cuse: fix memory leak
|
|
Pull drm fixes from Dave Airlie:
"Not too much this time.
- One nouveau workaround extended to a few more GPUs
- Some amdgpu big endian fixes, and a regression fixer
- Some vmwgfx fixes
- One ttm locking fix
- One vgaarb fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
vgaarb: fix signal handling in vga_get()
radeon: Fix VCE IB test on Big-Endian systems
radeon: Fix VCE ring test for Big-Endian systems
radeon/cik: Fix GFX IB test on Big-Endian
drm/amdgpu: fix the lost duplicates checking
drm/nouveau/pmu: remove whitelist for PGOB-exit WAR, enable by default
drm/vmwgfx: Implement the cursor_set2 callback v2
drm/vmwgfx: fix a warning message
drm/ttm: Fixed a read/write lock imbalance
|
|
The rule definitions here aren't really valid, they would
be rejected if it came from userspace due to the bandwidth
specified being bigger than the rule's width.
This is fairly much inconsequential since the other rules
around them do enable the bandwidth, but express that better
using the NL80211_RRF_AUTO_BW flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently the BUG_ON() checks do not give enough information about the
PTEs being set. This patch changes BUG_ON to WARN_ONCE and dumps the
values of the old and new PTEs. In addition, the checks are only made if
the new PTE entry is valid.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
|
|
cfg80211 module prints a lot of messages like below. Actually printing
once is acceptable but sometimes it will print again and again, it looks
very annoying. It is better to change these detail messages to debugging
only.
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
The changes in this patch is to replace pr_info with pr_debug in function
print_rd_rules and print_regdomain_info
Signed-off-by: Dave Young <dyoung@redhat.com>
[change some pr_err() statements to at least keep the alpha2]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of having this Kconfig option, which just *floods* the
kernel log,
* remove the per-channel prints that are fairly useless anyway
* convert the conditional printing to pr_debug()
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Linux on Vybrid used several different L2 latencies so far, none
of them seem to be the right ones. According to the application note
AN4947 ("Understanding Vybrid Architecture"), the tag portion runs
on CPU clock and is inside the L2 cache controller, whereas the data
portion is stored in the external SRAM running on platform clock.
Hence it is likely that the correct value requires a higher data
latency then tag latency.
These are the values which have been used so far:
- The mainline values:
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
Those values have lead to problems on higher clocks. They look
like a poor translation from the reset values (missing +1 offset
and a mix up between tag/latency values).
- The Linux 3.0 (SoC vendor BSP) values (converted to DT notation):
arm,data-latency = <4 2 3>
arm,tag-latency = <4 2 3>
The cache initialization function along with the value matches the
i.MX6 code from the same kernel, so it seems that those values have
just been copied.
- The Colibri values:
arm,data-latency = <2 1 2>;
arm,tag-latency = <3 2 3>;
Those were a mix between the values of the Linux 3.0 based BSP and
the mainline values above.
- The SoC Reset values (converted to DT notation):
arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
So far there is no official statement on what the correct values are.
See also the related Freescale community thread:
https://community.freescale.com/message/579785#579785
For now, the reset values seem to be the best bet. Remove all other
"bogus" values and use the reset value on vf610.dtsi level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
minor change, indenting is one tab out.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This patch is derived from
commit 6301566e0b2d ("ath9k: export HW random number generator"),
We evaluated the entropy of the ADC data on QCA9531, QCA9561, QCA955x,
and AR9340, and it has sufficient quality random data (at least 10 bits
and up to 22 bits of min-entropy for a 32-bit value). We conservatively
assume the min-entropy is 10 bits out of 32 bits. Thus, ATH9K_RNG_BUF_SIZE
is set to 320 (u32) i.e., 1.25 kilobytes of data is inserted to fill up
the pool as soon as the entropy counter becomes 896/4096 (set by random.c).
Since ADC was not designed to be a dedicated HW RNG, we do not want to bind
it to /dev/hwrng framework directly. This patch feeds the entropy directly
from the WiFi driver to the input pool. The ADC register output is only
used as a seed for the Linux entropy pool. No conditioning is needed,
since all the conditioning is performed by the pool itself.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When rx stopped, AR_RX_FILTER should be cleared, but in
ath9k_hw_setrxfilter(), ATH9K_RX_FILTER_CONTROL_WRAPPER will always
be set for ar9462/ar9565.
Fix this by moving the code in ath9k_hw_setrxfilter() to
ath_calcrxfilter().
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This gives a user a chance to know why a firmware load
is failing.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
My previous patch incorrectly reported the antenna
for 2x2 devices. It should be a mask instead of
a numeric count. This patch fixes that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The maximum chunks used by the function is
(SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE + 1).
The original commands array had space for
(SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE) commands.
When the last chunk is used (len > 4 * WSPI_MAX_CHUNK_SIZE), the last
command is stored outside the bounds of the commands array.
Oops 5 (page fault) is generated during current wl1271 firmware load
attempt:
root@debian-armhf:~# ifconfig wlan0 up
[ 294.312399] Unable to handle kernel paging request at virtual address
00203fc4
[ 294.320173] pgd = de528000
[ 294.323028] [00203fc4] *pgd=00000000
[ 294.326916] Internal error: Oops: 5 [#1] SMP ARM
[ 294.331789] Modules linked in: bnep rfcomm bluetooth ipv6 arc4 wl12xx
wlcore mac80211 musb_dsps cfg80211 musb_hdrc usbcore usb_common
wlcore_spi omap_rng rng_core musb_am335x omap_wdt cpufreq_dt thermal_sys
hwmon
[ 294.351838] CPU: 0 PID: 1827 Comm: ifconfig Not tainted
4.2.0-00002-g3e9ad27-dirty #78
[ 294.360154] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 294.366557] task: dc9d6d40 ti: de550000 task.ti: de550000
[ 294.372236] PC is at __spi_validate+0xa8/0x2ac
[ 294.376902] LR is at __spi_sync+0x78/0x210
[ 294.381200] pc : [<c049c760>] lr : [<c049ebe0>] psr: 60000013
[ 294.381200] sp : de551998 ip : de5519d8 fp : 00200000
[ 294.393242] r10: de551c8c r9 : de5519d8 r8 : de3a9000
[ 294.398730] r7 : de3a9258 r6 : de3a9400 r5 : de551a48 r4 :
00203fbc
[ 294.405577] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 :
de3a9000
[ 294.412420] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM
Segment user
[ 294.419918] Control: 10c5387d Table: 9e528019 DAC: 00000015
[ 294.425954] Process ifconfig (pid: 1827, stack limit = 0xde550218)
[ 294.432437] Stack: (0xde551998 to 0xde552000)
...
[ 294.883613] [<c049c760>] (__spi_validate) from [<c049ebe0>]
(__spi_sync+0x78/0x210)
[ 294.891670] [<c049ebe0>] (__spi_sync) from [<bf036598>]
(wl12xx_spi_raw_write+0xfc/0x148 [wlcore_spi])
[ 294.901661] [<bf036598>] (wl12xx_spi_raw_write [wlcore_spi]) from
[<bf21c694>] (wlcore_boot_upload_firmware+0x1ec/0x458 [wlcore])
[ 294.914038] [<bf21c694>] (wlcore_boot_upload_firmware [wlcore]) from
[<bf24532c>] (wl12xx_boot+0xc10/0xfac [wl12xx])
[ 294.925161] [<bf24532c>] (wl12xx_boot [wl12xx]) from [<bf20d5cc>]
(wl1271_op_add_interface+0x5b0/0x910 [wlcore])
[ 294.936364] [<bf20d5cc>] (wl1271_op_add_interface [wlcore]) from
[<bf15c4ac>] (ieee80211_do_open+0x44c/0xf7c [mac80211])
[ 294.947963] [<bf15c4ac>] (ieee80211_do_open [mac80211]) from
[<c0537978>] (__dev_open+0xa8/0x110)
[ 294.957307] [<c0537978>] (__dev_open) from [<c0537bf8>]
(__dev_change_flags+0x88/0x148)
[ 294.965713] [<c0537bf8>] (__dev_change_flags) from [<c0537cd0>]
(dev_change_flags+0x18/0x48)
[ 294.974576] [<c0537cd0>] (dev_change_flags) from [<c05a55a0>]
(devinet_ioctl+0x6b4/0x7d0)
[ 294.983191] [<c05a55a0>] (devinet_ioctl) from [<c0517040>]
(sock_ioctl+0x1e4/0x2bc)
[ 294.991244] [<c0517040>] (sock_ioctl) from [<c017d378>]
(do_vfs_ioctl+0x420/0x6b0)
[ 294.999208] [<c017d378>] (do_vfs_ioctl) from [<c017d674>]
(SyS_ioctl+0x6c/0x7c)
[ 295.006880] [<c017d674>] (SyS_ioctl) from [<c000f4c0>]
(ret_fast_syscall+0x0/0x54)
[ 295.014835] Code: e1550004 e2444034 0a00007d e5953018 (e5942008)
[ 295.021544] ---[ end trace 66ed188198f4e24e ]---
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
All interface layer related to scheduled scan are moved in
fwil_types.h
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The pcie suspend and resume routines contain some error prints,
which should have been debug prints.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Got a hint on IRC that a 43242 dongle for LG smart TV's works with
brcmfmac:
> Hello - I recently got a LG AN-WF500 wireless dongle for LG's SmartTVs.
> From the information I gathered it uses a Broadcom chipset BCM43242.
> The device should have been supported by brcmfmac kernel driver if it used
> USB IDs 0a5c:bd1f.
> My device however identifies itself as "ID 043e:3101 LG Electronics USA, Inc.".
> I then tried adding the USB ID to the driver with
> "echo "043e 3101" > /sys/bus/usb/drivers/brcmfmac/new_id" and it just works.
> The kernel provides the following information.
> [15958.851291] usb 3-1.1.3: new high-speed USB device number 53 using ehci-pci
> [15958.946723] usb 3-1.1.3: New USB device found, idVendor=043e, idProduct=3101
> [15958.946728] usb 3-1.1.3: New USB device strings: Mfr=1, Product=4, SerialNumber=3
> [15958.946731] usb 3-1.1.3: Product: Composite Wireless Adapter
> [15958.946733] usb 3-1.1.3: Manufacturer: Broadcom
> [15958.946735] usb 3-1.1.3: SerialNumber: 28458
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
brcmf_msgbuf_ioctl_resp_wake() seems to be missing a memory barrier
which might cause the waker to not notice the waiter and miss sending a
wake_up as in the following figure.
brcmf_msgbuf_ioctl_resp_wake brcmf_msgbuf_ioctl_resp_wait
------------------------------------------------------------------------
if (waitqueue_active(&msgbuf->ioctl_resp_wait))
/* The CPU might reorder the test for
the waitqueue up here, before
prior writes complete */
/* wait_event_timeout */
/* __wait_event_timeout */
/* ___wait_event */
prepare_to_wait_event(&wq, &__wait,
state);
if (msgbuf->ctl_completed)
...
msgbuf->ctl_completed = true;
schedule_timeout(__ret))
------------------------------------------------------------------------
There are three other place in drivers/net/wireless/brcm80211/brcmfmac/
which have similar code. The attached patch removes the call to
waitqueue_active() leaving just wake_up() behind. This fixes the
problem because the call to spin_lock_irqsave() in wake_up() will be an
ACQUIRE operation.
I found this issue when I was looking through the linux source code
for places calling waitqueue_active() before wake_up*(), but without
preceding memory barriers, after sending a patch to fix a similar
issue in drivers/tty/n_tty.c (Details about the original issue can be
found here: https://lkml.org/lkml/2015/9/28/849).
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
IBSS got broken over time. Disconnect events should not be given
for IBSS mode and connect events for IBSS need to have channel
information.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The interface combinations are intended for use-case in which the driver
handles multiple interface concurrently. This means that the combinations
do not need to be checked when there is only a single interface active.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
No need to pass timing configuration in local functions as they are
static anyway.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With the new optimized do_div() code, some versions of gcc
produce obviously incorrect code that leads to a link error
in iwlegacy/common.o:
drivers/built-in.o: In function `il_send_rxon_timing':
:(.text+0xa6b4d4): undefined reference to `____ilog2_NaN'
:(.text+0xa6b4f0): undefined reference to `__aeabi_uldivmod'
In a few thousand randconfig builds, I have seen this problem
a couple of times in this file, but never anywhere else in the
kernel, so we can try to work around this in the only file
that shows the behavior, by marking the il_adjust_beacon_interval
function as noinline, which convinces gcc to use the unoptimized
do_div() all the time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Free skb for received frames with a wrong checksum. This can happen
pretty rapidly, exhausting all memory.
This fixes a memleak (detected with kmemleak). Originally found while
using monitor mode, but it also appears during managed mode (once the
link is up).
Cc: stable@vger.kernel.org
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move constants to the right of binary operators.
Generated by: scripts/coccinelle/misc/compare_const_fl.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move constants to the right of binary operators.
Generated by: scripts/coccinelle/misc/compare_const_fl.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
EU is not a valid country in db.txt file. Hence regulatory_hint
returns failure if EEPROM provides region code as 0x30. Let's
use FR for 0x30.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If device has already received country information from
EEPROM, we won't parse AP's country IE and download it to
firmware. We will also set regulatory flags to disable beacon
hints and ignore country IE.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Driver gets country information from EEPROM during
initialization. We will call regulatory_hint to update
current regulatory domain.
As by default world regulatory domain is selected by
cfg80211, country '00' from EEPROM is ignored.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
It's been observed that even if firmware returns an error
for a configuration command, we go ahead and start AP.
This patch changes the command type from async to sync
so that threads waits for command response and return
failure start AP.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Even if ADHOC start or join attempt is failed, these commands
are returned with success status by firmware. Actual connection
result is provided inside command response.
This patch parses the adhoc connection result and resets
connection state variables if connection is not successful.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This code was supposed to trigger a BUG() if we truncate the output but
it's off by one so it allows one character to be truncated. Really
drivers shouldn't call BUG_ON() and especially for something minor like
this so I've changed it to a WARN_ON().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The current code returns success if prism2_init_local_data() fails, but
we want to return an error code. Also we can remove the bogus
ret initializer because it is wrong and never used.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We already know that "wep_key->key_length" is set so there is no need to
check again. Also the last curly brace was indented too far.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This code causes a static checker warning because we check for
"if (ret == 0)" but we have already had verified that was true. Clean
it up a little.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If the mode is NL80211_IFTYPE_UNSPECIFIED then we return success at the
start of the function so this condition is never true.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is a null ptr check for fws to set bcmc_credit_check, however,
there a lock and unlock on fws should only performed if fwts is
also not null to also avoid a potential null pointer deference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Align to new wl18xx sg parameters.
This requires to split both wl12xx/wl18xx enumerators.
Signed-off-by: Guy Mishol <guym@ti.com>
Acked-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There are few defects in vga_get() related to signal hadning:
- we shouldn't check for pending signals for TASK_UNINTERRUPTIBLE
case;
- if we found pending signal we must remove ourself from wait queue
and change task state back to running;
- -ERESTARTSYS is more appropriate, I guess.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: stable@vger.kernel.org
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
into drm-fixes
some big endian fixes and one regression fix.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
radeon: Fix VCE IB test on Big-Endian systems
radeon: Fix VCE ring test for Big-Endian systems
radeon/cik: Fix GFX IB test on Big-Endian
drm/amdgpu: fix the lost duplicates checking
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.4-rc4" from Tony Lindgren
Few fixes for omaps for v4.4-rc cycle:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
* tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
|
|
The recent change to use a pwm lookup table for the ezx machines
was incomplete and only changed the a780 model, but not the
other ones in the same file.
This adds the missing calls to pwm_add_table().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c3322022897c ("ARM: pxa: ezx: Use PWM lookup table")
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
git://git.infradead.org/users/hesselba/linux-berlin into fixes
Merge "Marvell Berlin fixes for 4.4-rc1 (round 1)" from Sebastian Hesselbarth:
- fix wrong SDIO DT clocks on BG2Q
* tag 'berlin-fixes-for-4.4-rc1-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Merge "Second fixes for 4.4" from Alexandre Belloni:
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
* tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes
Merge "Fixes for Exynos" from Krzysztof Kozlowski:
1. Fix potential NULL pointer dereference in Exynos PMU driver.
2. Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
* tag 'samsung-fixes-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Most are minor to important fixes.
There is one performance enhancement that I took on the grounds that
failing to check if other processes can run before running what's
intended to be a background, idle-time task is a bug, even though the
primary effect of the fix is to improve performance (and it was a very
simple patch)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx5: Postpone remove_keys under knowledge of coming preemption
IB/mlx4: Use vmalloc for WR buffers when needed
IB/mlx4: Use correct order of variables in log message
iser-target: Remove explicit mlx4 work-around
mlx4: Expose correct max_sge_rd limit
IB/mad: Require CM send method for everything except ClassPortInfo
IB/cma: Add a missing rcu_read_unlock()
IB core: Fix ib_sg_to_pages()
IB/srp: Fix srp_map_sg_fr()
IB/srp: Fix indirect data buffer rkey endianness
IB/srp: Initialize dma_length in srp_map_idb
IB/srp: Fix possible send queue overflow
IB/srp: Fix a memory leak
IB/sa: Put netlink request into the request list before sending
IB/iser: use sector_div instead of do_div
IB/core: use RCU for uverbs id lookup
IB/qib: Minor fixes to qib per SFF 8636
IB/core: Fix user mode post wr corruption
IB/qib: Fix qib_mr structure
|
|
|
|
We removed CLK_IGNORE_UNUSED from CLKID_SDIO's flag, so the sdhci0 and
sdhci1 don't work. We fix this by adding the optional 2nd clock for
BG2Q's sdhci0 and sdhci1. This patch brings another benefit: the 2nd
clock can be disabled during runtime pm, so saves power a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
The optional 2nd clock is CLKID_SDIO. We removed CLK_IGNORE_UNUSED
from CLKID_SDIO's flag, so the sdhci2 doesn't work. This patch fixes
this issue by correcting the sdhci2's 2nd clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Again less intensive changes in this rc: you can find only a few
HD-audio fixes (noise fixes for Intel Broxton chip and a few Thinkpad
models, quirks for Alienware 17 and Packard Bell DOTS) in addition to
a long-standing rme96 bug fix"
* tag 'sound-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/ca0132 - quirk for Alienware 17 2015
ALSA: hda - Fix noise problems on Thinkpad T440s
ALSA: hda - Fixing speaker noise on the two latest thinkpad models
ALSA: hda - Add inverted dmic for Packard Bell DOTS
ALSA: hda - Fix playback noise with 24/32 bit sample size on BXT
ALSA: rme96: Fix unexpected volume reset after rate changes
|
|
The EP93xx is registering a clocksource of 40 bits with
clocksource_mmio_init() but this is not working because of this
artificial limitation. It works fine to lift the uppe limit to
64 bits, and since cycle_t is u64, it should intuitively have been
like that from the beginning.
Fixes: 000bc17817bf "ARM: ep93xx: switch to GENERIC_CLOCKEVENTS"
Reported-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1449768101-6879-1-git-send-email-linus.walleij@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Both the 32bit and 64bit versions of the GICv3 header file are using
barriers, but neglect to include barrier.h, leading to an interesting
splat in some circumstances.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1449483072-17694-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When the GICv3 header file is used in a C file that doesn't include
any of the OF stuff, we end up with a bunch of ugly warnings.
Let's keep GCC quiet by adding a forward declaration.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1449483072-17694-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If dm_btree_del()'s call to push_frame() fails, e.g. due to
btree_node_validator finding invalid metadata, the dm_btree_del() error
path must unlock all frames (which have active dm-bufio buffers) that
were pushed onto the del_stack.
Otherwise, dm_bufio_client_destroy() will BUG_ON() because dm-bufio
buffers have leaked, e.g.:
device-mapper: bufio: leaked buffer 3, hold count 1, list 0
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
Some users of rfkill, like NFC and cfg80211, use a dynamic name when
allocating rfkill, in those cases dev_name(). Therefore, the pointer
passed to rfkill_alloc() might not be valid forever, I specifically
found the case that the rfkill name was quite obviously an invalid
pointer (or at least garbage) when the wiphy had been renamed.
Fix this by making a copy of the rfkill name in rfkill_alloc().
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pull VFIO fixes from Alex Williamson:
- Various fixes for removing redundancy, const'ifying structs, avoiding
stack usage, fixing WARN usage (Krzysztof Kozlowski, Julia Lawall,
Kees Cook, Dan Carpenter)
- Revert No-IOMMU mode as the intended user has not emerged (Alex
Williamson)
* tag 'vfio-v4.4-rc5' of git://github.com/awilliam/linux-vfio:
Revert: "vfio: Include No-IOMMU mode"
vfio: fix a warning message
vfio: platform: remove needless stack usage
vfio-pci: constify pci_error_handlers structures
vfio: Drop owner assignment from platform_driver
|
|
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit 8cbd4c2f6a99 ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DT fixes from Rob Herring:
"I think this should be all for 4.4:
- Fix incorrect warning about overlapping memory regions
- Export of_irq_find_parent again which was made static in 4.4, but
has users pending for 4.5.
- Fix of_msi_map_rid declaration location
- Fix re-entrancy for of_fdt_unflatten_tree
- Clean-up of phys_addr_t printks"
* tag 'devicetree-fixes-for-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/irq: move of_msi_map_rid declaration to the correct ifdef section
of/irq: Export of_irq_find_parent again
of/fdt: Add mutex protection for calls to __unflatten_device_tree()
of/address: fix typo in comment block of of_translate_one()
of: do not use 0x in front of %pa
of: Fix comparison of reserved memory regions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One small build fix, a couple do_div() fixes, and a fix for the gpio
basic clock type are the major changes here. There's also a couple
fixes for the TI, sunxi, and scpi clock drivers"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi: pll2: Fix clock running too fast
clk: scpi: add missing of_node_put
clk: qoriq: fix memory leak
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
clk: mmp: add linux/clk.h includes
clk: ti: drop locking code from mux/divider drivers
clk: ti816x: Add missing dmtimer clkdev entries
clk: ti: fapll: fix wrong do_div() usage
clk: ti: clkt_dpll: fix wrong do_div() usage
clk: gpio: Get parent clk names in of_gpio_clk_setup()
|
|
Pull IPMI fix from Corey Minyard:
"Fix an Oops if an interrupt occurs at startup. This can happen on
some hardware"
* tag 'for-linus-4.4-1' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: move timer init to before irq is setup
|
|
We encountered a panic on boot in ipmi_si on a dell per320 due to an
uninitialized timer as follows.
static int smi_start_processing(void *send_info,
ipmi_smi_t intf)
{
/* Try to claim any interrupts. */
if (new_smi->irq_setup)
new_smi->irq_setup(new_smi);
--> IRQ arrives here and irq handler tries to modify uninitialized timer
which triggers BUG_ON(!timer->function) in __mod_timer().
Call Trace:
<IRQ>
[<ffffffffa0532617>] start_new_msg+0x47/0x80 [ipmi_si]
[<ffffffffa053269e>] start_check_enables+0x4e/0x60 [ipmi_si]
[<ffffffffa0532bd8>] smi_event_handler+0x1e8/0x640 [ipmi_si]
[<ffffffff810f5584>] ? __rcu_process_callbacks+0x54/0x350
[<ffffffffa053327c>] si_irq_handler+0x3c/0x60 [ipmi_si]
[<ffffffff810efaf0>] handle_IRQ_event+0x60/0x170
[<ffffffff810f245e>] handle_edge_irq+0xde/0x180
[<ffffffff8100fc59>] handle_irq+0x49/0xa0
[<ffffffff8154643c>] do_IRQ+0x6c/0xf0
[<ffffffff8100ba53>] ret_from_intr+0x0/0x11
/* Set up the timer that drives the interface. */
setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi);
The following patch fixes the problem.
To: Openipmi-developer@lists.sourceforge.net
To: Corey Minyard <minyard@acm.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # Applies cleanly to 3.10-, needs small rework before
|
|
ROL on a 32 bit integer with a shift of 32 or more is undefined and the
result is arch-dependent. Avoid this by handling the trivial case of
roling by 0 correctly.
The trivial solution of checking if shift is 0 breaks gcc's detection
of this code as a ROL instruction, which is unacceptable.
This bug was reported and fixed in GCC
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=57157):
The standard rotate idiom,
(x << n) | (x >> (32 - n))
is recognized by gcc (for concreteness, I discuss only the case that x
is an uint32_t here).
However, this is portable C only for n in the range 0 < n < 32. For n
== 0, we get x >> 32 which gives undefined behaviour according to the
C standard (6.5.7, Bitwise shift operators). To portably support n ==
0, one has to write the rotate as something like
(x << n) | (x >> ((-n) & 31))
And this is apparently not recognized by gcc.
Note that this is broken on older GCCs and will result in slower ROL.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When applying block operations (BOPs) do not remove them from the
uncommitted BOP ring-buffer until after they've been applied -- in case
we recurse.
Also, perform BOP_INC operation, in dm_sm_metadata_create() and
sm_metadata_extend(), in terms of the uncommitted BOP ring-buffer rather
than using direct calls to sm_ll_inc().
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
When you take a metadata snapshot the btree roots for the mapping and
details tree need to have their reference counts incremented so they
persist for the lifetime of the metadata snap.
The roots being incremented were those currently written in the
superblock, which could possibly be out of date if concurrent IO is
triggering new mappings, breaking of sharing, etc.
Fix this by performing a commit with the metadata lock held while taking
a metadata snapshot.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for-v4.4-rc5
Hopefully final set of fixes for v4.4 release cycle.
There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.
A NULL pointer dereference fix for the MSM phy driver.
The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes, both -stable fodder (9p one all way back to 2.6.32,
dio - to all branches where "Fix negative return from dio read beyond
eof" will end up it; it's a fixup to commit marked for -stable)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the regression from "direct-io: Fix negative return from dio read beyond eof"
9p: ->evict_inode() should kick out ->i_data, not ->i_mapping
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are more fixes I'd like to have in v4.4. Several for the Altera
driver added for v4.4, and one for an MSI domain problem that affects
several arm64 platforms:
MSI:
- Only use the generic MSI layer when domain is hierarchical (Marc
Zyngier)
Altera host bridge driver:
- Fix loop in tlp_read_packet() (Dan Carpenter)
- Fix Requester ID for config accesses (Ley Foon Tan)
- Check TLP completion status (Ley Foon Tan)
- Fix error when INTx is 4 (Ley Foon Tan)"
* tag 'pci-v4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: altera: Fix error when INTx is 4
PCI: altera: Check TLP completion status
PCI: altera: Fix Requester ID for config accesses
PCI: altera: Fix loop in tlp_read_packet()
PCI/MSI: Only use the generic MSI layer when domain is hierarchical
|
|
The Alienware 17 (2015) has the same card and pin configuration of the
Alienware 15, so the same quirks must be applied.
Signed-off-by: Gabriele Martino <g.martino@gmx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fail with error when no DMA controller is set.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In checking fixes for of_irq_find_parent declaration location, I found
that of_msi_map_rid is also wrong. of_msi_map_rid is not implemented for
Sparc, so it should not be in the Sparc specific section of the header.
Move it to just depend on OF_IRQ.
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
of_irq_find_parent was made static since it had no users outside of
of_irq.c. Export it again since we are going to use it again.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[robh: move of_irq_find_parent to correct ifdef section]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Lenovo Thinkpad T440s suffers from constant background noises, and it
seems to be a generic hardware issue on this model:
https://forums.lenovo.com/t5/ThinkPad-T400-T500-and-newer-T/T440s-speaker-noise/td-p/1339883
As the noise comes from the analog loopback path, disabling the path
is the easy workaround.
Also, the machine gives significant cracking noises at PM suspend. A
workaround found by trial-and-error is to disable the shutup callback
currently used for ALC269-variant.
This patch addresses these noise issues by introducing a new fixup
chain. Although the same workaround might be applicable to other
Thinkpad models, it's applied only to T440s (17aa:220c) in this patch,
so far, just to be safe (you chicken!). As a compromise, a new model
option string "tp440" is provided now, though, so that owners of other
Thinkpad models can test it more easily.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=958504
Reported-and-tested-by: Tim Hardeck <thardeck@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Ilan's previous commit 1b894521e60c ("mac80211: handle HW
ROC expired properly") neglected to take into account that
hw_begun was now always set in the software implementation
as well as the offloaded case.
Fix hw_begun to only apply to the offloaded case to make
the check in Ilan's commit safe and correct.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch makes the VCE IB test pass on Big-Endian systems. It converts
to little-endian the contents of the VCE message.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch fixes the VCE ring test when running on Big-Endian machines.
Every write to the ring needs to be translated to little-endian.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch makes the IB test on the GFX ring pass for CI-based cards
installed in Big-Endian machines.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Cc: stable@vger.kernel.org
|
|
The cmac_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~thomash/linux into drm-fixes
Pull request of 2015-12-08
A couple of fixes for vmwgfx. A WARN() fix by Dan Carpenter,
a TTM read/write lock imbalance causing occasional hangs with Wayland and
an implementation of cursor_set2 to fix incorrectly offset Wayland cursors.
* tag 'vmwgfx-fixes-4.4-151208' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Implement the cursor_set2 callback v2
drm/vmwgfx: fix a warning message
drm/ttm: Fixed a read/write lock imbalance
|
|
Just the one commit I mentioned earlier, making the PGOB workaround the
default.
* 'linux-4.4' of https://github.com/skeggsb/linux:
drm/nouveau/pmu: remove whitelist for PGOB-exit WAR, enable by default
|
|
These fields are updated but never read.
Remove the overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under heavy TX load, bnx2x_poll() can loop forever and trigger
soft lockup bugs.
A napi poll handler must yield after one TX completion round,
risk of livelock is too high otherwise.
Bug is very easy to trigger using a debug build, and udp flood, because
of added cpu cycles in TX completion, and we do not receive enough
packets to break the loop.
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch 9497df88ab5567daa001829051c5f87161a81ff0 ("rhashtable:
Fix reader/rehash race") added a pair of barriers. In fact the
wmb is superfluous because every subsequent write to the old or
new hash table uses rcu_assign_pointer, which itself carriers a
full barrier prior to the assignment.
Therefore we may remove the explicit wmb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hariprasad Shenai says:
====================
Update Kconfig and some fixes for cxgb4
This series update Kconfig to add description for Chelsio's next
generation T6 family of adapters, also fixes ethtool stats alignment
and prevents simultaneous execution of service_ofldq thread, deals with
queue wrap around and adds some fl counters for debugging purpose and
device ID for new T5 adapters.
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
Thanks
V2: Declare 'service_ofldq_running' as bool in Patch 4/7 ("cxgb4: prevent
simultaneous execution of service_ofldq()") based on review comment
by David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Free List DMA Mapping Errors to SGE Queue info for
Free Lists. Add Free List "Low" counter to count the number of times we
see the number of pointers that we _think_ the hardware sees in the
Free List below the Egress Threshold.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The WR headers may not fit within one descriptor.
So we need to deal with wrap-around here.
Based on original patch by Pranjal Joshi <pjoshi@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change mutual exclusion mechanism to prevent multiple threads of
execution from running in service_ofldq() at the same time. The old
mechanism used an implicit guard on the down-call path and none on the
restart path and wasn't working. This checking makes the mechanism
explicit and is much easier to understand as a result.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use helper macro ACCESS_ONCE() to load from the SGE status page
to prevent the compiler loading multiple times.
Based on original work by Mike Werner <werner@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
here is the patch raising the performance of XGE by:
1)changes the way page management method for enet momery, and
2)reduces the count of rmb, and
3)adds Memory prefetching
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 527d10ef3a315d3cb9dc098dacd61889a6c26439.
The reverted commit breaks cxlflash devices following an EEH reset (and
possibly other cxl devices, however this has not been tested).
The reverted commit changed the behaviour of eeh_reset_device() so that PHB
PEs are not unfrozen following the completion of the reset. This should not
be problematic, as no device resources should have been associated with the
PHB PE.
However, when attempting to load the cxlflash driver after a reset, the
driver attempts to read Vital Product Data through a call to
pci_read_vpd() (which is called on the physical cxl device, not on the
virtual AFU device). pci_read_vpd() in turn attempts to read from the cxl
device's config space. This fails, as the PE it's trying to read from is
still frozen. In turn, the driver gets an -ENODEV and fails to initialise.
It appears this issue only affects some parts of the VPD area, as "lspci
-vvv", which only reads a subset of the VPD bytes, is not broken by the
original patch.
At this stage, we don't fully understand why we're trying to read a frozen
PE, and we don't know how this affects other cxl devices. It is possible
that there is an underlying bug in the cxl driver or the powerpc CAPI
support code, or alternatively a bug in the PCI resource allocation/mapping
code that is incorrectly mapping resources to PE#0.
As such, this fix is incomplete, however it is necessary to prevent a
serious regression in CAPI support.
In the meantime, revert the commit, especially as it was intended to be a
non-functional change.
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Ian Munsie <imunsie@au1.ibm.com>
Cc: Daniel Axtens <dja@axtens.net>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In cgroup v1, dealing with cgroup membership was difficult because the
number of membership associations was unbound. As a result, cgroup v1
grew several controllers whose primary purpose is either tagging
membership or pull in configuration knobs from other subsystems so
that cgroup membership test can be avoided.
net_cls and net_prio controllers are examples of the latter. They
allow configuring network-specific attributes from cgroup side so that
network subsystem can avoid testing cgroup membership; unfortunately,
these are not only cumbersome but also problematic.
Both net_cls and net_prio aren't properly hierarchical. Both inherit
configuration from the parent on creation but there's no interaction
afterwards. An ancestor doesn't restrict the behavior in its subtree
in anyway and configuration changes aren't propagated downwards.
Especially when combined with cgroup delegation, this is problematic
because delegatees can mess up whatever network configuration
implemented at the system level. net_prio would allow the delegatees
to set whatever priority value regardless of CAP_NET_ADMIN and net_cls
the same for classid.
While it is possible to solve these issues from controller side by
implementing hierarchical allowable ranges in both controllers, it
would involve quite a bit of complexity in the controllers and further
obfuscate network configuration as it becomes even more difficult to
tell what's actually being configured looking from the network side.
While not much can be done for v1 at this point, as membership
handling is sane on cgroup v2, it'd be better to make cgroup matching
behave like other network matches and classifiers than introducing
further complications.
In preparation, this patch updates sock->sk_cgrp_data handling so that
it points to the v2 cgroup that sock was created in until either
net_prio or net_cls is used. Once either of the two is used,
sock->sk_cgrp_data reverts to its previous role of carrying prioidx
and classid. This is to avoid adding yet another cgroup related field
to struct sock.
As the mode switching can happen at most once per boot, the switching
mechanism is aimed at lowering hot path overhead. It may leak a
finite, likely small, number of cgroup refs and report spurious
prioidx or classid on switching; however, dynamic updates of prioidx
and classid have always been racy and lossy - socks between creation
and fd installation are never updated, config changes don't update
existing sockets at all, and prioidx may index with dead and recycled
cgroup IDs. Non-critical inaccuracies from small race windows won't
make any noticeable difference.
This patch doesn't make use of the pointer yet. The following patch
will implement netfilter match for cgroup2 membership.
v2: Use sock_cgroup_data to avoid inflating struct sock w/ another
cgroup specific field.
v3: Add comments explaining why sock_data_prioidx() and
sock_data_classid() use different fallback values.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Daniel Wagner <daniel.wagner@bmw-carit.de>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce sock->sk_cgrp_data which is a struct sock_cgroup_data.
->sk_cgroup_prioidx and ->sk_classid are moved into it. The struct
and its accessors are defined in cgroup-defs.h. This is to prepare
for overloading the fields with a cgroup pointer.
This patch mostly performs equivalent conversions but the followings
are noteworthy.
* Equality test before updating classid is removed from
sock_update_classid(). This shouldn't make any noticeable
difference and a similar test will be implemented on the helper side
later.
* sock_update_netprioidx() now takes struct sock_cgroup_data and can
be moved to netprio_cgroup.h without causing include dependency
loop. Moved.
* The dummy version of sock_update_netprioidx() converted to a static
inline function while at it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netprio builds per-netdev contiguous priomap array which is indexed by
css->id. The array is allocated using kzalloc() effectively limiting
the maximum ID supported to some thousand range. This patch caps the
maximum supported css->id to USHRT_MAX which should be way above what
is actually useable.
This allows reducing sock->sk_cgrp_prioidx to u16 from u32. The freed
up part will be used to overload the cgroup related fields.
sock->sk_cgrp_prioidx's position is swapped with sk_mark so that the
two cgroup related fields are adjacent.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Preparatory changes for some new socket cgroup infrastructure
and netfilter targets.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This file was originally cloned off of the MPC8641D-HPCN reference
platform, which actually had a PHY IRQ line connected. However this
board does not. The bogus entry was largely inert and went undetected
until commit 321beec5047af83db90c88114b7e664b156f49fe ("net: phy: Use
interrupts when available in NOLINK state") was added to the tree.
With the above commit, the board fails to NFS boot since it sits waiting
for a PHY IRQ event that of course never arrives. Removing the bogus
entries from the DTS file fixes the issue.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This reverts commit 0d76d6e8b2507983a2cae4c09880798079007421 and merge
commit c402293bd76fbc93e52ef8c0947ab81eea3ae019, reversing changes made
to c89359a42e2a49656451569c382eed63e781153c.
The virtio-vsock device specification is not finalized yet. Michael
Tsirkin voiced concerned about merging this code when the hardware
interface (and possibly the userspace interface) could still change.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sergei Shtylyov says:
====================
sh_eth: optimize MDIO code
Here's a set of 3 patches against DaveM's 'net-next.git' repo which
gets rid of ~35 LoCs in the MDIO bitbang methods.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the MDIO bitbang code consolidation, there's no need anymore for
bb_{set|clr}() as well as bb_read() -- just expand them inline, thus
saving more LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sh_mm[cd]_ctrl() and sh_set_mdio() all look mostly the same -- factor out
their common code and put it into sh_mdio_ctrl().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDIO control bits are always mapped to the same bits of the same register
(PIR), so there's no need to store their masks in the 'struct bb_info'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The xgene_mac_ops and xgene_port_ops structures are never modified, so
declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull uml fixes from Richard Weinberger:
"This contains various bug fixes, most of them are fall out from the
merge window"
* 'for-linus-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: fix returns without va_end
um: Fix fpstate handling
arch: um: fix error when linking vmlinux.
um: Fix get_signal() usage
|
|
NVIDIA have indicated that the workaround is required on all GK10[467]
boards that have the PGOB fuse set.
I've left the commandline option in place for now, as paranoia.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The current (new) code recalculates the new work timeout
for software remain-on-channel whenever any item started.
In two of the callers of ieee80211_handle_roc_started(),
this is completely pointless since they're for hardware
and will skip the recalculation entirely; it's necessary
only in the case of having just added a new item to the
list, as in the last remaining case the recalculation had
just been done.
This last case, however, is also problematic - if one of
the items on the list actually expires during the recalc
the list iteration outside becomes corrupted and crashes.
Fix this by moving the recalculation to the only place
where it's required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The remove_keys() logic is performed as garbage collection task. Such
task is intended to be run when no other active processes are running.
The need_resched() will return TRUE if there are user tasks to be
activated in near future.
In such case, we don't execute remove_keys() and postpone
the garbage collection work to try to run in next cycle,
in order to free CPU resources to other tasks.
The possible pseudo-code to trigger such scenario:
1. Allocate a lot of MR to fill the cache above the limit.
2. Wait a small amount of time "to calm" the system.
3. Start CPU extensive operations on multi-node cluster.
4. Expect performance degradation during MR cache shrink operation.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There are several hits that WR buffer allocation(kmalloc) failed.
It failed at order 3 and/or 4 contigous pages allocation. At the same time
there are actually 100MB+ free memory but well fragmented.
So try vmalloc when kmalloc failed.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is a mis-order in mlx4 log. Fix it.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"More change than I'd have liked at this stage. The pids controller
and the changes made to cgroup core to support it introduced and
revealed several important issues.
- Assigning membership to a newly created task and migrating it can
race leading to incorrect accounting. Oleg fixed it by widening
threadgroup synchronization. It looks like we'll be able to merge
it with a different percpu rwsem which is used in fork path making
things simpler and cheaper.
- The recent change to extend cgroup membership to zombies (so that
pid accounting can extend till the pid is actually released) missed
pinning the underlying data structures leading to use-after-free.
Fixed.
- v2 hierarchy was calling subsystem callbacks with the wrong target
cgroup_subsys_state based on the incorrect assumption that they
share the same target. pids is the first controller affected by
this. Subsys callbacks updated so that they can deal with
multi-target migrations"
* 'for-4.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup_pids: don't account for the root cgroup
cgroup: fix handling of multi-destination migration from subtree_control enabling
cgroup_freezer: simplify propagation of CGROUP_FROZEN clearing in freezer_attach()
cgroup: pids: kill pids_fork(), simplify pids_can_fork() and pids_cancel_fork()
cgroup: pids: fix race between cgroup_post_fork() and cgroup_migrate()
cgroup: make css_set pin its css's to avoid use-afer-free
cgroup: fix cftype->file_offset handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Nothing too interesting. All are device specific additions and
workarounds"
* 'for-4.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata/sata_fsl.c: add ATA_FLAG_NO_LOG_PAGE to blacklist the controller for log page reads
libata-eh.c: Introduce new ata port flag for controller which lockup on read log page
sata_sil: disable trim
AHCI: Fix softreset failed issue of Port Multiplier
sata/mvebu: use #ifdef around suspend/resume code
ahci: Order SATA device IDs for codename Lewisburg
ahci: Add Device ID for Intel Sunrise Point PCH
|
|
When using va_list ensure that va_start will be followed by va_end.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
The x86 FPU cleanup changed fpstate to a plain integer.
UML on x86 has to deal with that too.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
On gcc Ubuntu 4.8.4-2ubuntu1~14.04, linking vmlinux fails with:
arch/um/os-Linux/built-in.o: In function `os_timer_create':
/android/kernel/android/arch/um/os-Linux/time.c:51: undefined reference to `timer_create'
arch/um/os-Linux/built-in.o: In function `os_timer_set_interval':
/android/kernel/android/arch/um/os-Linux/time.c:84: undefined reference to `timer_settime'
arch/um/os-Linux/built-in.o: In function `os_timer_remain':
/android/kernel/android/arch/um/os-Linux/time.c:109: undefined reference to `timer_gettime'
arch/um/os-Linux/built-in.o: In function `os_timer_one_shot':
/android/kernel/android/arch/um/os-Linux/time.c:132: undefined reference to `timer_settime'
arch/um/os-Linux/built-in.o: In function `os_timer_disable':
/android/kernel/android/arch/um/os-Linux/time.c:145: undefined reference to `timer_settime'
This is because -lrt appears in the generated link commandline
after arch/um/os-Linux/built-in.o. Fix this by removing -lrt from
arch/um/Makefile and adding it to the UM-specific section of
scripts/link-vmlinux.sh.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
If get_signal() returns us a signal to post
we must not call it again, otherwise the already
posted signal will be overridden.
Before commit a610d6e672d this was the case as we stopped
the while after a successful handle_signal().
Cc: <stable@vger.kernel.org> # 3.10-
Fixes: a610d6e672d ("pull clearing RESTORE_SIGMASK into block_sigmask()")
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"This tree includes four core perf fixes for misc bugs, three fixes to
x86 PMU drivers, and two updates to old email addresses"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Do not send exit event twice
perf/x86/intel: Fix INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_NA macro
perf/x86/intel: Make L1D_PEND_MISS.FB_FULL not constrained on Haswell
perf: Fix PERF_EVENT_IOC_PERIOD deadlock
treewide: Remove old email address
perf/x86: Fix LBR call stack save/restore
perf: Update email address in MAINTAINERS
perf/core: Robustify the perf_cgroup_from_task() RCU checks
perf/core: Fix RCU problem with cgroup context switching code
|
|
Module couldn't release resource properly during the initialization. To
fix this issue, we will clean up the proper resource before returning.
Signed-off-by: Minfei Huang <mnfhuang@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
eof"
Sure, it's better to bail out of past-the-eof read and return 0 than return
a bogus negative value on such. Only we'd better make sure we are bailing out
with 0 and not -ENOMEM...
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
For block devices the pagecache is associated with the inode
on bdevfs, not with the aliasing ones on the mountable filesystems.
The latter have its own ->i_data empty and ->i_mapping pointing
to the (unique per major/minor) bdevfs inode. That guarantees
cache coherence between all block device inodes with the same
device number.
Eviction of an alias inode has no business trying to evict the
pages belonging to bdevfs one; moreover, ->i_mapping is only
safe to access when the thing is opened. At the time of
->evict_inode() the victim is definitely *not* opened. We are
about to kill the address space embedded into struct inode
(inode->i_data) and that's what we need to empty of any pages.
9p instance tries to empty inode->i_mapping instead, which is
both unsafe and bogus - if we have several device nodes with
the same device number in different places, closing one of them
should not try to empty the (shared) page cache.
Fortunately, other instances in the tree are OK; they are
evicting from &inode->i_data instead, as 9p one should.
Cc: stable@vger.kernel.org # v2.6.32+, ones prior to 2.6.36 need only half of that
Reported-by: "Suzuki K. Poulose" <Suzuki.Poulose@arm.com>
Tested-by: "Suzuki K. Poulose" <Suzuki.Poulose@arm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The driver now exposes sufficient limits so we can
avoid having mlx4 specific work-around.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
mlx4 devices (ConnectX-2, ConnectX-3) has a limitation
where rdma read work queue entries cannot exceed 512 bytes.
A rdma_read wqe needs to fit in 512 bytes:
- wqe control segment (16 bytes)
- rdma segment (16 bytes)
- scatter elements (16 bytes each)
So max_sge_rd should be: (512 - 16 - 16) / 16 = 30.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Vallo says:
====================
brcfmac
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
====================
Conflicts:
drivers/net/wireless/ath/ath10k/pci.c
The conflict resolution at:
http://article.gmane.org/gmane.linux.kernel.next/37391
by Stephen Rothwell was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Receipt of CM MAD with other than the Send method for an attribute
other than the ClassPortInfo attribute is invalid.
CM attributes other than ClassPortInfo only use the send method.
The SRP initiator does not maintain a timeout policy for CM connect
requests relies on the CM layer to do that. The result was that
the SRP initiator hung as the connect request never completed.
A new SRP target has been observed to respond to Send CM REQ
with GetResp of CM REQ with bad status. This is non conformant
with IBA spec but exposes a vulnerability in the current MAD/CM
code which will respond to the incoming GetResp of CM REQ as if
it was a valid incoming Send of CM REQ rather than tossing
this on the floor. It also causes the MAD layer not to
retransmit the original REQ even though it has not received a REP.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Ensure that validate_ipv4_net_dev() calls rcu_read_unlock() if
fib_lookup() fails. Detected by sparse. Compile-tested only.
Fixes: "IB/cma: Validate routing of incoming requests" (commit f887f2ac87c2).
Cc: Haggai Eran <haggaie@mellanox.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
As the kernel generally uses negated error numbers, *err needs to be
compared with -EAGAIN (d'oh).
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Fixes: ea3793ee29d3 ("core: enable more fine-grained datagram reception control")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__unflatten_device_tree() calls unflatten_dt_node(), which declares
a static variable. It is therefore not reentrant.
One of the callers of __unflatten_device_tree(), unflatten_device_tree(),
is only called once during early initialization and does not need to be
protected. The other caller, of_fdt_unflatten_tree(), can be called at
any time, possibly multiple times in parallel. This can happen, for
example, if multiple devicetree overlays have to be loaded and installed.
Without this protection, errors such as the following may be seen.
kernel: End of tree marker overwritten: e6a3a458
kernel: find_target_node:
Failed to find target-indirect node at /fragment@0
kernel: __of_overlay_create: of_build_overlay_info() failed for tree@/
Add a mutex to of_fdt_unflatten_tree() to make the call reentrant.
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
removed write permission for writeable attributes. Correct attribute
permissions.
Fixes: 76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Remove ath9k_mod_tsf64_tu() function while we could
use div_u64_rem() function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This is useful for MCC debugging and bug fixing.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In case of MCC and AP interface, add also NOA attr
that will inform stations about absence of an AP.
There is a chance that some stations will handle
this NOA attr correctly and will know exactly when
AP is present/absent.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In case we get BSS_CHANGED_P2P_PS early, from
mac80211, we didn't set NOA timer correctly,
while p2p_ps_vif was NULL.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When adding NOA attr enable Opportunistic Power Save.
Before we calculate ctwindow but didn't enable oppps.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
After queue nullfunc for MCC case, we hit WARN_ON
in xmit.c:2398 while skb priority wasn't set.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Use u32 while ath9k_hw_gettsf32() and
ath9k_hw_gen_timer_start() require u32.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
AP/GO will aprear after NOA, wait 1ms to be sure AP
could receive/answer this frames.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
