| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
|
|
Pull networking fixes from David Miller:
1) Fix checksumming regressions, from Tom Herbert.
2) Undo unintentional permissions changes for SCTP rto_alpha and
rto_beta sysfs knobs, from Denial Borkmann.
3) VXLAN, like other IP tunnels, should advertize it's encapsulation
size using dev->needed_headroom instead of dev->hard_header_len.
From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: sctp: fix permissions for rto_alpha and rto_beta knobs
vxlan: Checksum fixes
net: add skb_pop_rcv_encapsulation
udp: call __skb_checksum_complete when doing full checksum
net: Fix save software checksum complete
net: Fix GSO constants to match NETIF flags
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
vxlan: use dev->needed_headroom instead of dev->hard_header_len
MAINTAINERS: update cxgb4 maintainer
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
|
|
Pull NVMe update from Matthew Wilcox:
"Mostly bugfixes again for the NVMe driver. I'd like to call out the
exported tracepoint in the block layer; I believe Keith has cleared
this with Jens.
We've had a few reports from people who're really pounding on NVMe
devices at scale, hence the timeout changes (and new module
parameters), hotplug cpu deadlock, tracepoints, and minor performance
tweaks"
[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
end up going away when mq conversion happens ]
* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
NVMe: Use Log Page constants in SCSI emulation
NVMe: Define Log Page constants
NVMe: Fix hot cpu notification dead lock
NVMe: Rename io_timeout to nvme_io_timeout
NVMe: Use last bytes of f/w rev SCSI Inquiry
NVMe: Adhere to request queue block accounting enable/disable
NVMe: Fix nvme get/put queue semantics
NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
NVMe: Make admin timeout a module parameter
NVMe: Make iod bio timeout a parameter
NVMe: Prevent possible NULL pointer dereference
NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
NVMe: Update data structures for NVMe 1.2
NVMe: Enable BUILD_BUG_ON checks
NVMe: Update namespace and controller identify structures to the 1.1a spec
NVMe: Flush with data support
NVMe: Configure support for block flush
NVMe: Add tracepoints
NVMe: Protect against badly formatted CQEs
...
|
|
Commit 3fd091e73b81 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.
RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:
[...]
C3) When a new RTT measurement R' is made, set
RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|
and
SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'
Note: The value of SRTT used in the update to RTTVAR
is its value before updating SRTT itself using the
second assignment. After the computation, update
RTO <- SRTT + 4 * RTTVAR.
C4) When data is in flight and when allowed by rule C5
below, a new RTT measurement MUST be made each round
trip. Furthermore, new RTT measurements SHOULD be
made no more than once per round trip for a given
destination transport address. There are two reasons
for this recommendation: First, it appears that
measuring more frequently often does not in practice
yield any significant benefit [ALLMAN99]; second,
if measurements are made more often, then the values
of RTO.Alpha and RTO.Beta in rule C3 above should be
adjusted so that SRTT and RTTVAR still adjust to
changes at roughly the same rate (in terms of how many
round trips it takes them to reflect new values) as
they would if making only one measurement per
round-trip and using RTO.Alpha and RTO.Beta as given
in rule C3. However, the exact nature of these
adjustments remains a research issue.
[...]
While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.
Fixes: 3fd091e73b81 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tom Herbert says:
====================
Fixes related to some recent checksum modifications.
- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5172927732f51fde
("net: Save software checksum complete") is not correct.
This patch:
1) Restores code in __skb_checksum_complete_header except for setting
CHECKSUM_UNNECESSARY. This function may be calculating checksum on
something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
checksum 0..skb->len is calculated without adding in pseudo header.
This value is saved in skb->csum and then the pseudo header is added
to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
set skb->csum_valid to whether checksum of zero was computed. This
allows skb_csum_unnecessary to return true without changing to
CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is just a couple of drivers (hpsa and lpfc) that got left out for
further testing in linux-next. We also have one fix to a prior
submission (qla2xxx sparse)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
lpfc: Update lpfc version to driver version 10.2.8001.0
lpfc: Fix ExpressLane priority setup
lpfc: mark old devices as obsolete
lpfc: Fix for initializing RRQ bitmap
lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
lpfc: Update lpfc version to driver version 10.2.8000.0
lpfc: Update Copyright on changed files from 8.3.45 patches
lpfc: Update Copyright on changed files
lpfc: Fixed locking for scsi task management commands
lpfc: Convert runtime references to old xlane cfg param to fof cfg param
lpfc: Fix FW dump using sysfs
lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
lpfc: Fixed kernel panic in lpfc_abort_handler
lpfc: Fix locking for postbufq when freeing
lpfc: Fix locking for lpfc_hba_down_post
lpfc: Fix dynamic transitions of FirstBurst from on to off
hpsa: fix handling of hpsa_volume_offline return value
hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
hpsa: remove messages about volume status VPD inquiry page not supported
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull more btrfs updates from Chris Mason:
"This has a few fixes since our last pull and a new ioctl for doing
btree searches from userland. It's very similar to the existing
ioctl, but lets us return larger items back down to the app"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix error handling in create_pending_snapshot
btrfs: fix use of uninit "ret" in end_extent_writepage()
btrfs: free ulist in qgroup_shared_accounting() error path
Btrfs: fix qgroups sanity test crash or hang
btrfs: prevent RCU warning when dereferencing radix tree slot
Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
btrfs: new ioctl TREE_SEARCH_V2
btrfs: tree_search, search_ioctl: direct copy to userspace
btrfs: new function read_extent_buffer_to_user
btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
btrfs: tree_search, search_ioctl: accept varying buffer
btrfs: tree_search: eliminate redundant nr_items check
|
|
Pull aio fix and cleanups from Ben LaHaise:
"This consists of a couple of code cleanups plus a minor bug fix"
* git://git.kvack.org/~bcrl/aio-next:
aio: cleanup: flatten kill_ioctx()
aio: report error from io_destroy() when threads race in io_destroy()
fs/aio.c: Remove ctx parameter in kiocb_cancel
|
|
Tetsuo Handa wrote:
"Commit 62a8067a7f35 ("bio_vec-backed iov_iter") introduced an unnamed
union inside a struct which gcc-4.4.7 cannot handle. Name the unnamed
union as u in order to fix build failure"
Let's do this instead: there is only one place in the entire tree that
steps into this breakage. Anon structs and unions work in older gcc
versions; as the matter of fact, we have those in the tree - see e.g.
struct ieee80211_tx_info in include/net/mac80211.h
What doesn't work is handling their initializers:
struct {
int a;
union {
int b;
char c;
};
} x[2] = {{.a = 1, .c = 'a'}, {.a = 0, .b = 1}};
is the obvious syntax for initializer, perfectly fine for C11 and
handled correctly by gcc-4.7 or later.
Earlier versions, though, break on it - declaration is fine and so's
access to fields (i.e. x[0].c = 'a'; would produce the right code), but
members of the anon structs and unions are not inserted into the right
namespace. Tellingly, those older versions will not barf on struct {int
a; struct {int a;};}; - looks like they just have it hacked up somewhere
around the handling of . and -> instead of doing the right thing.
The easiest way to deal with that crap is to turn initialization of
those fields (in the only place where we have such initializer of
iov_iter) into plain assignment.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi
Pull HSI build fixes from Sebastian Reichel:
- tighten dependency between ssi-protocol and omap-ssi to fix build
failures with randconfig.
- use normal module refcounting in omap driver to fix build with
disabled module support
* tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
hsi: omap_ssi_port: use normal module refcounting
HSI: fix omap ssi driver dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"A first GPIO fix for the v3.16 series, this was serious since it
blocks the OMAP boot.
Sending you this vital fix before leaving for a short vacation so it
does not sit collecting dust in my tree for no good reason.
Apart from this, our v3.16 cycle looks like a good start"
* tag 'gpio-v3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: of: Fix handling for deferred probe for -gpio suffix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 vdso fixes from Peter Anvin:
"Fixes for x86/vdso.
One is a simple build fix for bigendian hosts, one is to make "make
vdso_install" work again, and the rest is about working around a bug
in Google's Go language -- two are documentation patches that improves
the sample code that the Go coders took, modified, and broke; the
other two implements a workaround that keeps existing Go binaries from
segfaulting at least"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Fix vdso_install
x86/vdso: Hack to keep 64-bit Go programs working
x86/vdso: Add PUT_LE to store little-endian values
x86/vdso/doc: Make vDSO examples more portable
x86/vdso/doc: Rename vdso_test.c to vdso_standalone_test_x86.c
x86, vdso: Remove one final use of htole16()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for Sensirion SHTC1 humidity / temperature sensor
- convert ltc4151 and vexpress drivers to use devm functions
- drop generic chip detection from lm85 driver
- avoid forward declarations in atxp1 driver
- fix sign extensions in ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: vexpress: Use devm helper for hwmon device registration
hwmon: (atxp1) Avoid forward declaration
hwmon: add support for Sensirion SHTC1 sensor
hwmon: (ltc4151) Convert to devm_hwmon_device_register_with_groups
hwmon: (lm85) Drop generic detection
hwmon: (ina2xx) Cast to s16 on shunt and current regs
|
|
Its too easy to add thousand of UDP sockets on a particular bucket,
and slow down an innocent multicast receiver.
Early demux is supposed to be an optimization, we should avoid spending
too much time in it.
It is interesting to note __udp4_lib_demux_lookup() only tries to
match first socket in the chain.
10 is the threshold we already have in __udp4_lib_lookup() to switch
to secondary hash.
Fixes: 421b3885bf6d5 ("udp: ipv4: Add udp early demux")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Held <drheld@google.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we mirror packets from a vxlan tunnel to other device,
the mirror device should see the same packets (that is, without
outer header). Because vxlan tunnel sets dev->hard_header_len,
tcf_mirred() resets mac header back to outer mac, the mirror device
actually sees packets with outer headers
Vxlan tunnel should set dev->needed_headroom instead of
dev->hard_header_len, like what other ip tunnels do. This fixes
the above problem.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stephen hemminger <stephen@networkplumber.org>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hari's been doing the patch submissions for a while now and he'll be
taking over as maintainer.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"make vdso_install" installs unstripped versions of the vdso objects
for the benefit of the debugger. This was broken by checkin:
6f121e548f83 x86, vdso: Reimplement vdso.so preparation in build-time C
The filenames are different now, so update the Makefile to cope.
This still installs the 64-bit vdso as vdso64.so. We believe this
will be okay, as the only known user is a patched gdb which is known
to use build-ids, but if it turns out to be a problem we may have to
add a link.
Inspired by a patch from Sam Ravnborg.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Tested-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/b10299edd8ba98d17e07dafcd895b8ecf4d99eff.1402586707.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
This patch contains several fixes for Scsi START_STOP_UNIT. The previous
code did not account for signed vs. unsigned arithmetic which resulted
in an invalid lowest power state caculation when the device only supports
1 power state.
The code for Power Condition == 2 (Idle) was not following the spec. The
spec calls for setting the device to specific power states, depending
upon Power Condition Modifier, without accounting for the number of
power states supported by the device.
The code for Power Condition == 3 (Standby) was using a hard-coded '0'
which is replaced with the macro POWER_STATE_0.
Signed-off-by: Dan McLeran <daniel.mcleran@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@linux.intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
|
fcebe456 cut and pasted some code to a later point
in create_pending_snapshot(), but didn't switch
to the appropriate error handling for this stage
of the function.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
If this condition in end_extent_writepage() is false:
if (tree->ops && tree->ops->writepage_end_io_hook)
we will then test an uninitialized "ret" at:
ret = ret < 0 ? ret : -EIO;
The test for ret is for the case where ->writepage_end_io_hook
failed, and we'd choose that ret as the error; but if
there is no ->writepage_end_io_hook, nothing sets ret.
Initializing ret to 0 should be sufficient; if
writepage_end_io_hook wasn't set, (!uptodate) means
non-zero err was passed in, so we choose -EIO in that case.
Signed-of-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
If tmp = ulist_alloc(GFP_NOFS) fails, we return without
freeing the previously allocated qgroups = ulist_alloc(GFP_NOFS)
and cause a memory leak.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Often when running the qgroups sanity test, a crash or a hang happened.
This is because the extent buffer the test uses for the root node doesn't
have an header level explicitly set, making it have a random level value.
This is a problem when it's not zero for the btrfs_search_slot() calls
the test ends up doing, resulting in crashes or hangs such as the following:
[ 6454.127192] Btrfs loaded, debug=on, assert=on, integrity-checker=on
(...)
[ 6454.127760] BTRFS: selftest: Running qgroup tests
[ 6454.127964] BTRFS: selftest: Running test_test_no_shared_qgroup
[ 6454.127966] BTRFS: selftest: Qgroup basic add
[ 6480.152005] BUG: soft lockup - CPU#0 stuck for 23s! [modprobe:5383]
[ 6480.152005] Modules linked in: btrfs(+) xor raid6_pq binfmt_misc nfsd auth_rpcgss oid_registry nfs_acl nfs lockd fscache sunrpc i2c_piix4 i2c_core pcspkr evbug psmouse serio_raw e1000 [last unloaded: btrfs]
[ 6480.152005] irq event stamp: 188448
[ 6480.152005] hardirqs last enabled at (188447): [<ffffffff8168ef5c>] restore_args+0x0/0x30
[ 6480.152005] hardirqs last disabled at (188448): [<ffffffff81698e6a>] apic_timer_interrupt+0x6a/0x80
[ 6480.152005] softirqs last enabled at (188446): [<ffffffff810516cf>] __do_softirq+0x1cf/0x450
[ 6480.152005] softirqs last disabled at (188441): [<ffffffff81051c25>] irq_exit+0xb5/0xc0
[ 6480.152005] CPU: 0 PID: 5383 Comm: modprobe Not tainted 3.15.0-rc8-fdm-btrfs-next-33+ #4
[ 6480.152005] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 6480.152005] task: ffff8802146125a0 ti: ffff8800d0d00000 task.ti: ffff8800d0d00000
[ 6480.152005] RIP: 0010:[<ffffffff81349a63>] [<ffffffff81349a63>] __write_lock_failed+0x13/0x20
[ 6480.152005] RSP: 0018:ffff8800d0d038e8 EFLAGS: 00000287
[ 6480.152005] RAX: 0000000000000000 RBX: ffffffff8168ef5c RCX: 000005deb8525852
[ 6480.152005] RDX: 0000000000000000 RSI: 0000000000001d45 RDI: ffff8802105000b8
[ 6480.152005] RBP: ffff8800d0d038e8 R08: fffffe12710f63db R09: ffffffffa03196fb
[ 6480.152005] R10: ffff8802146125a0 R11: ffff880214612e28 R12: ffff8800d0d03858
[ 6480.152005] R13: 0000000000000000 R14: ffff8800d0d00000 R15: ffff8802146125a0
[ 6480.152005] FS: 00007f14ff804700(0000) GS:ffff880215e00000(0000) knlGS:0000000000000000
[ 6480.152005] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 6480.152005] CR2: 00007fff4df0dac8 CR3: 00000000d1796000 CR4: 00000000000006f0
[ 6480.152005] Stack:
[ 6480.152005] ffff8800d0d03908 ffffffff810ae967 0000000000000001 ffff8802105000b8
[ 6480.152005] ffff8800d0d03938 ffffffff8168e57e ffffffffa0319c16 0000000000000007
[ 6480.152005] ffff880210500000 ffff880210500100 ffff8800d0d039b8 ffffffffa0319c16
[ 6480.152005] Call Trace:
[ 6480.152005] [<ffffffff810ae967>] do_raw_write_lock+0x47/0xa0
[ 6480.152005] [<ffffffff8168e57e>] _raw_write_lock+0x5e/0x80
[ 6480.152005] [<ffffffffa0319c16>] ? btrfs_tree_lock+0x116/0x270 [btrfs]
[ 6480.152005] [<ffffffffa0319c16>] btrfs_tree_lock+0x116/0x270 [btrfs]
[ 6480.152005] [<ffffffffa02b2acb>] btrfs_lock_root_node+0x3b/0x50 [btrfs]
[ 6480.152005] [<ffffffffa02b81a6>] btrfs_search_slot+0x916/0xa20 [btrfs]
[ 6480.152005] [<ffffffff811a727f>] ? create_object+0x23f/0x300
[ 6480.152005] [<ffffffffa02b9958>] btrfs_insert_empty_items+0x78/0xd0 [btrfs]
[ 6480.152005] [<ffffffffa036041a>] insert_normal_tree_ref.constprop.4+0xa2/0x19a [btrfs]
[ 6480.152005] [<ffffffffa03605c3>] test_no_shared_qgroup+0xb1/0x1ca [btrfs]
[ 6480.152005] [<ffffffff8108cad6>] ? local_clock+0x16/0x30
[ 6480.152005] [<ffffffffa035ef8e>] btrfs_test_qgroups+0x1ae/0x1d7 [btrfs]
[ 6480.152005] [<ffffffffa03a69d2>] ? ftrace_define_fields_btrfs_space_reservation+0xfd/0xfd [btrfs]
[ 6480.152005] [<ffffffffa03a6a86>] init_btrfs_fs+0xb4/0x153 [btrfs]
[ 6480.152005] [<ffffffff81000352>] do_one_initcall+0x102/0x150
[ 6480.152005] [<ffffffff8103d223>] ? set_memory_nx+0x43/0x50
[ 6480.152005] [<ffffffff81682668>] ? set_section_ro_nx+0x6d/0x74
[ 6480.152005] [<ffffffff810d91cc>] load_module+0x1cdc/0x2630
(...)
Therefore initialize the extent buffer as an empty leaf (level 0).
Issue easy to reproduce when btrfs is built as a module via:
$ for ((i = 1; i <= 1000000; i++)); do rmmod btrfs; modprobe btrfs; done
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Mark the dereference as protected by lock. Not doing so triggers
an RCU warning since the radix tree assumed that RCU is in use.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Steps to reproduce:
# mkfs.btrfs -f /dev/sd[b-f] -m raid5 -d raid5
# mkfs.ext4 /dev/sdc --->corrupt one of btrfs device
# mount /dev/sdb /mnt -o degraded
# btrfs scrub start -BRd /mnt
This is because readahead would skip missing device, this is not true
for RAID5/6, because REQ_GET_READ_MIRRORS return 1 for RAID5/6 block
mapping. If expected data locates in missing device, readahead thread
would not call __readahead_hook() which makes event @rc->elems=0
wait forever.
Fix this problem by checking return value of btrfs_map_block(),we
can only skip missing device safely if there are several mirrors.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
This new ioctl call allows the user to supply a buffer of varying size in which
a tree search can store its results. This is much more flexible if you want to
receive items which are larger than the current fixed buffer of 3992 bytes or
if you want to fetch more items at once. Items larger than this buffer are for
example some of the type EXTENT_CSUM.
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name>
Signed-off-by: Chris Mason <clm@fb.com>
Acked-by: David Sterba <dsterba@suse.cz>
|
|
The nvme-scsi file defined its own Log Page constant. Use the
newly-defined one from the header file instead.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
|
Taken from the 1.1a version of the spec
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
|
There is a potential dead lock if a cpu event occurs during nvme probe
since it registered with hot cpu notification. This fixes the race by
having the module register with notification outside of probe rather
than have each device register.
The actual work is done in a scheduled work queue instead of in the
notifier since assigning IO queues has the potential to block if the
driver creates additional queues.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of changes are small and easy cleanup or fixes:
- a few HD-audio Realtek codec fixes and quirks
- Intel HDMI audio fixes for Broadwell and Haswell / ValleyView
- FireWire sound stack cleanups
- a couple of sequencer core fixes
- compress ABI fix for 64bit
- conversion to modern ktime*() API"
* tag 'sound-fix-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: hda/realtek - Add more entry for enable HP mute led
ALSA: hda - Add quirk for external mic on Lifebook U904
ALSA: hda - fix a fixup value for codec alc293 in the pin_quirk table
ALSA: intel8x0: Use ktime and ktime_get()
ALSA: core: Use ktime_get_ts()
ALSA: hda - verify pin:converter connection on unsol event for HSW and VLV
ALSA: compress: Cancel the optimization of compiler and fix the size of struct for all platform.
ALSA: hda - Add quirk for ABit AA8XE
Revert "ALSA: hda - mask buggy stream DMA0 for Broadwell display controller"
ALSA: hda - using POS_FIX_LPIB on Broadwell HDMI Audio
ALSA: hda/realtek - Add support of ALC667 codec
ALSA: hda/realtek - Add more codec rename
ALSA: hda/realtek - New vendor ID for ALC233
ALSA: hda - add two new pin tables
ALSA: hda/realtek - Add support of ALC891 codec
ALSA: seq: Continue broadcasting events to ports if one of them fails
ALSA: bebob: Remove unused function prototype
ALSA: fireworks: Remove meaningless mutex_destroy()
ALSA: fireworks: Remove a constant over width to which it's applied
ALSA: fireworks: Improve comments about Fireworks transaction
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm fix from David Teigland:
"This contains one small fix related to resending SCTP messages"
* tag 'dlm-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: keep listening connection alive with sctp mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sergeh/linux-security
Pull more security layer updates from Serge Hallyn:
"A few more commits had previously failed to make it through
security-next into linux-next but this week made it into linux-next.
At least commit "ima: introduce ima_kernel_read()" was deemed critical
by Mimi to make this merge window.
This is a temporary tree just for this request. Mimi has pointed me
to some previous threads about keeping maintainer trees at the
previous release, which I'll certainly do for anything long-term,
after talking with James"
* 'serge-next-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sergeh/linux-security:
ima: introduce ima_kernel_read()
evm: prohibit userspace writing 'security.evm' HMAC value
ima: check inode integrity cache in violation check
ima: prevent unnecessary policy checking
evm: provide option to protect additional SMACK xattrs
evm: replace HMAC version with attribute mask
ima: prevent new digsig xattr from being replaced
|
|
More HP machine need mute led support.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
According to the bug reporter (Данило Шеган), the external mic
starts to work and has proper jack detection if only pin 0x19
is marked properly as an external headset mic.
AlsaInfo at https://bugs.launchpad.net/ubuntu/+source/pulseaudio/+bug/1328587/+attachment/4128991/+files/AlsaInfo.txt
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1328587
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The fixup value for codec alc293 was set to
ALC269_FIXUP_DELL1_MIC_NO_PRESENCE by a mistake, if we don't fix it,
the Dock mic will be overwriten by the headset mic, this will make
the Dock mic can't work.
Cc: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"This has a mix of bug fixes and cleanups.
Alex's patch fixes a rare race in RBD. Ilya's patches fix an ENOENT
check when a second rbd image is mapped and a couple memory leaks.
Zheng fixes several issues with fragmented directories and multiple
MDSs. Josh fixes a spin/sleep issue, and Josh and Guangliang's
patches fix setting and unsetting RBD images read-only.
Naturally there are several other cleanups mixed in for good measure"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (23 commits)
rbd: only set disk to read-only once
rbd: move calls that may sleep out of spin lock range
rbd: add ioctl for rbd
ceph: use truncate_pagecache() instead of truncate_inode_pages()
ceph: include time stamp in every MDS request
rbd: fix ida/idr memory leak
rbd: use reference counts for image requests
rbd: fix osd_request memory leak in __rbd_dev_header_watch_sync()
rbd: make sure we have latest osdmap on 'rbd map'
libceph: add ceph_monc_wait_osdmap()
libceph: mon_get_version request infrastructure
libceph: recognize poolop requests in debugfs
ceph: refactor readpage_nounlock() to make the logic clearer
mds: check cap ID when handling cap export message
ceph: remember subtree root dirfrag's auth MDS
ceph: introduce ceph_fill_fragtree()
ceph: handle cap import atomically
ceph: pre-allocate ceph_cap struct for ceph_add_cap()
ceph: update inode fields according to issued caps
rbd: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull OMAP3 updates from Mauro Carvalho Chehab:
"Some driver improvements on OMAP3. This series depend on some iommu
patches already merged"
* 'topic/omap3isp' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (26 commits)
[media] omap3isp: Rename isp_buffer isp_addr field to dma
[media] omap3isp: Move to videobuf2
[media] v4l: vb2: Add a function to discard all DONE buffers
[media] omap3isp: Cancel all queued buffers when stopping the video stream
[media] omap3isp: Move buffer irqlist to isp_buffer structure
[media] omap3isp: Move queue irqlock to isp_video structure
[media] omap3isp: Move queue mutex to isp_video structure
[media] omap3isp: queue: Don't build scatterlist for kernel buffer
[media] omap3isp: Use the ARM DMA IOMMU-aware operations
[media] omap3isp: queue: Use sg_alloc_table_from_pages()
[media] omap3isp: queue: Map PFNMAP buffers to device
[media] omap3isp: queue: Fix the dma_map_sg() return value check
[media] omap3isp: queue: Allocate kernel buffers with dma_alloc_coherent
[media] omap3isp: queue: Inline the ispmmu_v(un)map functions
[media] omap3isp: queue: Merge the prepare and sglist functions
[media] omap3isp: queue: Use sg_table structure
[media] omap3isp: queue: Move IOMMU handling code to the queue
[media] omap3isp: video: Set the buffer bytesused field at completion time
[media] omap3isp: ccdc: Use the DMA API for FPC
[media] omap3isp: ccdc: Use the DMA API for LSC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add support for T10 PI pass-through between vhost-scsi +
virtio-scsi (MST + Paolo + MKP + nab)
- Add support for T10 PI in qla2xxx target mode (Quinn + MKP + hch +
nab, merged through scsi.git)
- Add support for percpu-ida pre-allocation in qla2xxx target code
(Quinn + nab)
- A number of iser-target fixes related to hardening the network
portal shutdown path (Sagi + Slava)
- Fix response length residual handling for a number of control CDBs
(Roland + Christophe V.)
- Various iscsi RFC conformance fixes in the CHAP authentication path
(Tejas and Calsoft folks + nab)
- Return TASK_SET_FULL status for tcm_fc(FCoE) DataIn + Response
failures (Vasu + Jun + nab)
- Fix long-standing ABORT_TASK + session reset hang (nab)
- Convert iser-initiator + iser-target to include T10 bytes into EDTL
(Sagi + Or + MKP + Mike Christie)
- Fix NULL pointer dereference regression related to XCOPY introduced
in v3.15 + CC'ed to v3.12.y (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (34 commits)
target: Fix NULL pointer dereference for XCOPY in target_put_sess_cmd
vhost-scsi: Include prot_bytes into expected data transfer length
TARGET/sbc,loopback: Adjust command data length in case pi exists on the wire
libiscsi, iser: Adjust data_length to include protection information
scsi_cmnd: Introduce scsi_transfer_length helper
target: Report correct response length for some commands
target/sbc: Check that the LBA and number of blocks are correct in VERIFY
target/sbc: Remove sbc_check_valid_sectors()
Target/iscsi: Fix sendtargets response pdu for iser transport
Target/iser: Fix a wrong dereference in case discovery session is over iser
iscsi-target: Fix ABORT_TASK + connection reset iscsi_queue_req memory leak
target: Use complete_all for se_cmd->t_transport_stop_comp
target: Set CMD_T_ACTIVE bit for Task Management Requests
target: cleanup some boolean tests
target/spc: Simplify INQUIRY EVPD=0x80
tcm_fc: Generate TASK_SET_FULL status for response failures
tcm_fc: Generate TASK_SET_FULL status for DataIN failures
iscsi-target: Reject mutual authentication with reflected CHAP_C
iscsi-target: Remove no-op from iscsit_tpg_del_portal_group
iscsi-target: Fix CHAP_A parameter list handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild misc updates from Michal Marek:
"This is the non-critical part of kbuild for v3.16-rc1:
- make deb-pkg can do s390x and arm64
- new patterns in scripts/tags.sh
- scripts/tags.sh skips userspace tools' sources (which sometimes
have copies of kernel structures) and symlinks
- improvements to the objdiff tool
- two new coccinelle patches
- other minor fixes"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts: objdiff: support directories for the augument of record command
scripts: objdiff: fix a comment
scripts: objdiff: change the extension of disassembly from .o to .dis
scripts: objdiff: improve path flexibility for record command
scripts: objdiff: remove unnecessary code
scripts: objdiff: direct error messages to stderr
scripts: objdiff: get the path to .tmp_objdiff more simply
deb-pkg: Add automatic support for s390x architecture
coccicheck: Add unneeded return variable test
kbuild: Fix a typo in documentation
kbuild: trivial - use tabs for code indent where possible
kbuild: trivial - remove trailing empty lines
coccinelle: Check for missing NULL terminators in of_device_id tables
scripts/tags.sh: ignore symlink'ed source files
scripts/tags.sh: add regular expression replacement pattern for memcg
builddeb: add arm64 in the supported architectures
builddeb: use $OBJCOPY variable instead of objcopy
scripts/tags.sh: ignore code of user space tools
scripts/tags.sh: add pattern for DEFINE_HASHTABLE
.gitignore: ignore Module.symvers in all directories
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
"Kbuild changes for v3.16-rc1:
- cross-compilation fix so that cc-option is testing the right
compiler
- Fix for make defconfig all
- Using relative paths to the object and source directory where
possible, plus fixes for the fallout of the change
- several cleanups in the Makefiles and scripts
The powerpc fix is from today, because it was only discovered
recently. The rest has been in linux-next for some time"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
powerpc: Avoid circular dependency with zImage.%
kbuild: create include/config directory in scripts/kconfig/Makefile
kbuild: do not create include/linux directory
Makefile: Fix unrecognized cross-compiler command line options
kbuild: do not add "selinux" to subdir- twice
um: Fix for relative objtree when generating x86 headers
kbuild: Use relative path when building in a subdir of the source tree
kbuild: Use relative path when building in the source tree
kbuild: Use relative path for $(objtree)
firmware: Use $(quote) in the Makefile
firmware: Simplify directory creation
kbuild: trivial - fix comment block indent
kbuild: trivial - remove trailing spaces
kbuild: support simultaneous "make %config" and "make all"
kbuild: move extra gcc checks to scripts/Makefile.extrawarn
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing cleanups and bugfixes from Steven Rostedt:
"One bug fix that goes back to 3.10. Accessing a non existent buffer
if "possible cpus" is greater than actual CPUs (including offline
CPUs).
Namhyung Kim did some reviews of the patches I sent this merge window
and found a memory leak and had a few clean ups"
* tag 'trace-3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix check of ftrace_trace_arrays list_empty() check
tracing: Fix leak of per cpu max data in instances
tracing: Cleanup saved_cmdlines_size changes
ring-buffer: Check if buffer exists before polling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull more powerpc updates from Ben Herrenschmidt:
"Here are the remaining bits I was mentioning earlier. Mostly bug
fixes and new selftests from Michael (yay !). He also removed the WSP
platform and A2 core support which were dead before release, so less
clutter.
One little "feature" I snuck in is the doorbell IPI support for
non-virtualized P8 which speeds up IPIs significantly between threads
of a core"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc/book3s: Fix some ABIv2 issues in machine check code
powerpc/book3s: Fix guest MC delivery mechanism to avoid soft lockups in guest.
powerpc/book3s: Increment the mce counter during machine_check_early call.
powerpc/book3s: Add stack overflow check in machine check handler.
powerpc/book3s: Fix machine check handling for unhandled errors
powerpc/eeh: Dump PE location code
powerpc/powernv: Enable POWER8 doorbell IPIs
powerpc/cpuidle: Only clear LPCR decrementer wakeup bit on fast sleep entry
powerpc/powernv: Fix killed EEH event
powerpc: fix typo 'CONFIG_PMAC'
powerpc: fix typo 'CONFIG_PPC_CPU'
powerpc/powernv: Don't escalate non-existing frozen PE
powerpc/eeh: Report frozen parent PE prior to child PE
powerpc/eeh: Clear frozen state for child PE
powerpc/powernv: Reduce panic timeout from 180s to 10s
powerpc/xmon: avoid format string leaking to printk
selftests/powerpc: Add tests of PMU EBBs
selftests/powerpc: Add support for skipping tests
selftests/powerpc: Put the test in a separate process group
selftests/powerpc: Fix instruction loop for ABIv2 (LE)
...
|
|
http://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
Pull blackfin updates from Steven Miao.
* tag 'blackfin-for-linus' of http://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
blackfin: defconfigs: add MTD_SPI_NOR (new dependency for M25P80)
Revert "blackfin: dma: current count mmr is read only"
bf533: fix build error: add linux/gpio.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq fixes from Ingo Molnar:
"Two changes: a cpu-hotplug/irq race fix, plus a HyperV related fix"
* 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Fix fixup_irqs() error handling
x86, irq, pic: Probe for legacy PIC and set legacy_pic appropriately
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more scheduler updates from Ingo Molnar:
"Second round of scheduler changes:
- try-to-wakeup and IPI reduction speedups, from Andy Lutomirski
- continued power scheduling cleanups and refactorings, from Nicolas
Pitre
- misc fixes and enhancements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Delete extraneous extern for to_ratio()
sched/idle: Optimize try-to-wake-up IPI
sched/idle: Simplify wake_up_idle_cpu()
sched/idle: Clear polling before descheduling the idle thread
sched, trace: Add a tracepoint for IPI-less remote wakeups
cpuidle: Set polling in poll_idle
sched: Remove redundant assignment to "rt_rq" in update_curr_rt(...)
sched: Rename capacity related flags
sched: Final power vs. capacity cleanups
sched: Remove remaining dubious usage of "power"
sched: Let 'struct sched_group_power' care about CPU capacity
sched/fair: Disambiguate existing/remaining "capacity" usage
sched/fair: Change "has_capacity" to "has_free_capacity"
sched/fair: Remove "power" from 'struct numa_stats'
sched: Fix signedness bug in yield_to()
sched/fair: Use time_after() in record_wakee()
sched/balancing: Reduce the rate of needless idle load balancing
sched/fair: Fix unlocked reads of some cfs_b->quota/period
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more perf updates from Ingo Molnar:
"A second round of perf updates:
- wide reaching kprobes sanitization and robustization, with the hope
of fixing all 'probe this function crashes the kernel' bugs, by
Masami Hiramatsu.
- uprobes updates from Oleg Nesterov: tmpfs support, corner case
fixes and robustization work.
- perf tooling updates and fixes from Jiri Olsa, Namhyung Ki, Arnaldo
et al:
* Add support to accumulate hist periods (Namhyung Kim)
* various fixes, refactorings and enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (101 commits)
perf: Differentiate exec() and non-exec() comm events
perf: Fix perf_event_comm() vs. exec() assumption
uprobes/x86: Rename arch_uprobe->def to ->defparam, minor comment updates
perf/documentation: Add description for conditional branch filter
perf/x86: Add conditional branch filtering support
perf/tool: Add conditional branch filter 'cond' to perf record
perf: Add new conditional branch filter 'PERF_SAMPLE_BRANCH_COND'
uprobes: Teach copy_insn() to support tmpfs
uprobes: Shift ->readpage check from __copy_insn() to uprobe_register()
perf/x86: Use common PMU interrupt disabled code
perf/ARM: Use common PMU interrupt disabled code
perf: Disable sampled events if no PMU interrupt
perf: Fix use after free in perf_remove_from_context()
perf tools: Fix 'make help' message error
perf record: Fix poll return value propagation
perf tools: Move elide bool into perf_hpp_fmt struct
perf tools: Remove elide setup for SORT_MODE__MEMORY mode
perf tools: Fix "==" into "=" in ui_browser__warning assignment
perf tools: Allow overriding sysfs and proc finding with env var
perf tools: Consider header files outside perf directory in tags target
...
|
|
The Go runtime has a buggy vDSO parser that currently segfaults.
This writes an empty SHT_DYNSYM entry that causes Go's runtime to
malfunction by thinking that the vDSO is empty rather than
malfunctioning by running off the end and segfaulting.
This affects x86-64 only as far as we know, so we do not need this for
the i386 and x32 vdsos.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/d10618176c4bd39b457a5e85c497295c90cab1bc.1402620737.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Add PUT_LE() by analogy with GET_LE() to write littleendian values in
addition to reading them.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/3d9b27e92745b27b6fda1b9a98f70dc9c1246c7a.1402620737.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
This adds a new vdso_test.c that's written entirely in C. It also
makes all of the vDSO examples work on 32-bit x86.
Cc: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/62b701fc44b79f118ac2b2d64d19965fc5c291fb.1402620737.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
This thing is hopelessly x86_64-specific: it's an example of how to
access the vDSO without any runtime support at all.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/3efc170e0e166e15f0150c9fdb37d52488b9c0a4.1402620737.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more locking changes from Ingo Molnar:
"This is the second round of locking tree updates for v3.16, offering
large system scalability improvements:
- optimistic spinning for rwsems, from Davidlohr Bueso.
- 'qrwlocks' core code and x86 enablement, from Waiman Long and PeterZ"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, locking/rwlocks: Enable qrwlocks on x86
locking/rwlocks: Introduce 'qrwlocks' - fair, queued rwlocks
locking/mutexes: Documentation update/rewrite
locking/rwsem: Fix checkpatch.pl warnings
locking/rwsem: Fix warnings for CONFIG_RWSEM_GENERIC_SPINLOCK
locking/rwsem: Support optimistic spinning
|
|
By copying each found item seperatly to userspace, we do not need extra
buffer in the kernel.
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name>
Signed-off-by: Chris Mason <clm@fb.com>
Acked-by: David Sterba <dsterba@suse.cz>
|
|
This new function reads the content of an extent directly to user memory.
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name>
Signed-off-by: Chris Mason <clm@fb.com>
Acked-by: David Sterba <dsterba@suse.cz>
|
|
If an item in tree_search is too large to be stored in the given buffer, return
the needed size (including the header).
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name>
Signed-off-by: Chris Mason <clm@fb.com>
Acked-by: David Sterba <dsterba@suse.cz>
|
|
In copy_to_sk, if an item is too large for the given buffer, it now returns
-EOVERFLOW instead of copying a search_header with len = 0. For backward
compatibility for the first item it still copies such a header to the buffer,
but not any other following items, which could have fitted.
tree_search changes -EOVERFLOW back to 0 to behave similiar to the way it
behaved before this patch.
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name>
Signed-off-by: Chris Mason <clm@fb.com>
Acked-by: David Sterba <dsterba@suse.cz>
|
|
rewrite search_ioctl to accept a buffer with varying size
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name>
Signed-off-by: Chris Mason <clm@fb.com>
Acked-by: David Sterba <dsterba@suse.cz>
|
|
If the amount of items reached the given limit of nr_items, we can leave
copy_to_sk without updating the key. Also by returning 1 we leave the loop in
search_ioctl without rechecking if we reached the given limit.
Signed-off-by: Gerhard Heift <Gerhard@Heift.Name>
Signed-off-by: Chris Mason <clm@fb.com>
Acked-by: David Sterba <dsterba@suse.cz>
|
|
Commit 8aac62706 "move exit_task_namespaces() outside of exit_notify"
introduced the kernel opps since the kernel v3.10, which happens when
Apparmor and IMA-appraisal are enabled at the same time.
----------------------------------------------------------------------
[ 106.750167] BUG: unable to handle kernel NULL pointer dereference at
0000000000000018
[ 106.750221] IP: [<ffffffff811ec7da>] our_mnt+0x1a/0x30
[ 106.750241] PGD 0
[ 106.750254] Oops: 0000 [#1] SMP
[ 106.750272] Modules linked in: cuse parport_pc ppdev bnep rfcomm
bluetooth rpcsec_gss_krb5 nfsd auth_rpcgss nfs_acl nfs lockd sunrpc
fscache dm_crypt intel_rapl x86_pkg_temp_thermal intel_powerclamp
kvm_intel snd_hda_codec_hdmi kvm crct10dif_pclmul crc32_pclmul
ghash_clmulni_intel aesni_intel aes_x86_64 glue_helper lrw gf128mul
ablk_helper cryptd snd_hda_codec_realtek dcdbas snd_hda_intel
snd_hda_codec snd_hwdep snd_pcm snd_page_alloc snd_seq_midi
snd_seq_midi_event snd_rawmidi psmouse snd_seq microcode serio_raw
snd_timer snd_seq_device snd soundcore video lpc_ich coretemp mac_hid lp
parport mei_me mei nbd hid_generic e1000e usbhid ahci ptp hid libahci
pps_core
[ 106.750658] CPU: 6 PID: 1394 Comm: mysqld Not tainted 3.13.0-rc7-kds+ #15
[ 106.750673] Hardware name: Dell Inc. OptiPlex 9010/0M9KCM, BIOS A08
09/19/2012
[ 106.750689] task: ffff8800de804920 ti: ffff880400fca000 task.ti:
ffff880400fca000
[ 106.750704] RIP: 0010:[<ffffffff811ec7da>] [<ffffffff811ec7da>]
our_mnt+0x1a/0x30
[ 106.750725] RSP: 0018:ffff880400fcba60 EFLAGS: 00010286
[ 106.750738] RAX: 0000000000000000 RBX: 0000000000000100 RCX:
ffff8800d51523e7
[ 106.750764] RDX: ffffffffffffffea RSI: ffff880400fcba34 RDI:
ffff880402d20020
[ 106.750791] RBP: ffff880400fcbae0 R08: 0000000000000000 R09:
0000000000000001
[ 106.750817] R10: 0000000000000000 R11: 0000000000000001 R12:
ffff8800d5152300
[ 106.750844] R13: ffff8803eb8df510 R14: ffff880400fcbb28 R15:
ffff8800d51523e7
[ 106.750871] FS: 0000000000000000(0000) GS:ffff88040d200000(0000)
knlGS:0000000000000000
[ 106.750910] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 106.750935] CR2: 0000000000000018 CR3: 0000000001c0e000 CR4:
00000000001407e0
[ 106.750962] Stack:
[ 106.750981] ffffffff813434eb ffff880400fcbb20 ffff880400fcbb18
0000000000000000
[ 106.751037] ffff8800de804920 ffffffff8101b9b9 0001800000000000
0000000000000100
[ 106.751093] 0000010000000000 0000000000000002 000000000000000e
ffff8803eb8df500
[ 106.751149] Call Trace:
[ 106.751172] [<ffffffff813434eb>] ? aa_path_name+0x2ab/0x430
[ 106.751199] [<ffffffff8101b9b9>] ? sched_clock+0x9/0x10
[ 106.751225] [<ffffffff8134a68d>] aa_path_perm+0x7d/0x170
[ 106.751250] [<ffffffff8101b945>] ? native_sched_clock+0x15/0x80
[ 106.751276] [<ffffffff8134aa73>] aa_file_perm+0x33/0x40
[ 106.751301] [<ffffffff81348c5e>] common_file_perm+0x8e/0xb0
[ 106.751327] [<ffffffff81348d78>] apparmor_file_permission+0x18/0x20
[ 106.751355] [<ffffffff8130c853>] security_file_permission+0x23/0xa0
[ 106.751382] [<ffffffff811c77a2>] rw_verify_area+0x52/0xe0
[ 106.751407] [<ffffffff811c789d>] vfs_read+0x6d/0x170
[ 106.751432] [<ffffffff811cda31>] kernel_read+0x41/0x60
[ 106.751457] [<ffffffff8134fd45>] ima_calc_file_hash+0x225/0x280
[ 106.751483] [<ffffffff8134fb52>] ? ima_calc_file_hash+0x32/0x280
[ 106.751509] [<ffffffff8135022d>] ima_collect_measurement+0x9d/0x160
[ 106.751536] [<ffffffff810b552d>] ? trace_hardirqs_on+0xd/0x10
[ 106.751562] [<ffffffff8134f07c>] ? ima_file_free+0x6c/0xd0
[ 106.751587] [<ffffffff81352824>] ima_update_xattr+0x34/0x60
[ 106.751612] [<ffffffff8134f0d0>] ima_file_free+0xc0/0xd0
[ 106.751637] [<ffffffff811c9635>] __fput+0xd5/0x300
[ 106.751662] [<ffffffff811c98ae>] ____fput+0xe/0x10
[ 106.751687] [<ffffffff81086774>] task_work_run+0xc4/0xe0
[ 106.751712] [<ffffffff81066fad>] do_exit+0x2bd/0xa90
[ 106.751738] [<ffffffff8173c958>] ? retint_swapgs+0x13/0x1b
[ 106.751763] [<ffffffff8106780c>] do_group_exit+0x4c/0xc0
[ 106.751788] [<ffffffff81067894>] SyS_exit_group+0x14/0x20
[ 106.751814] [<ffffffff8174522d>] system_call_fastpath+0x1a/0x1f
[ 106.751839] Code: c3 0f 1f 44 00 00 55 48 89 e5 e8 22 fe ff ff 5d c3
0f 1f 44 00 00 55 65 48 8b 04 25 c0 c9 00 00 48 8b 80 28 06 00 00 48 89
e5 5d <48> 8b 40 18 48 39 87 c0 00 00 00 0f 94 c0 c3 0f 1f 80 00 00 00
[ 106.752185] RIP [<ffffffff811ec7da>] our_mnt+0x1a/0x30
[ 106.752214] RSP <ffff880400fcba60>
[ 106.752236] CR2: 0000000000000018
[ 106.752258] ---[ end trace 3c520748b4732721 ]---
----------------------------------------------------------------------
The reason for the oops is that IMA-appraisal uses "kernel_read()" when
file is closed. kernel_read() honors LSM security hook which calls
Apparmor handler, which uses current->nsproxy->mnt_ns. The 'guilty'
commit changed the order of cleanup code so that nsproxy->mnt_ns was
not already available for Apparmor.
Discussion about the issue with Al Viro and Eric W. Biederman suggested
that kernel_read() is too high-level for IMA. Another issue, except
security checking, that was identified is mandatory locking. kernel_read
honors it as well and it might prevent IMA from calculating necessary hash.
It was suggested to use simplified version of the function without security
and locking checks.
This patch introduces special version ima_kernel_read(), which skips security
and mandatory locking checking. It prevents the kernel oops to happen.
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
|
|
Calculating the 'security.evm' HMAC value requires access to the
EVM encrypted key. Only the kernel should have access to it. This
patch prevents userspace tools(eg. setfattr, cp --preserve=xattr)
from setting/modifying the 'security.evm' HMAC value directly.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
|
|
When IMA did not support ima-appraisal, existance of the S_IMA flag
clearly indicated that the file was measured. With IMA appraisal S_IMA
flag indicates that file was measured and/or appraised. Because of
this, when measurement is not enabled by the policy, violations are
still reported.
To differentiate between measurement and appraisal policies this
patch checks the inode integrity cache flags. The IMA_MEASURED
flag indicates whether the file was actually measured, while the
IMA_MEASURE flag indicates whether the file should be measured.
Unfortunately, the IMA_MEASURED flag is reset to indicate the file
needs to be re-measured. Thus, this patch checks the IMA_MEASURE
flag.
This patch limits the false positive violation reports, but does
not fix it entirely. The IMA_MEASURE/IMA_MEASURED flags are
indications that, at some point in time, the file opened for read
was in policy, but might not be in policy now (eg. different uid).
Other changes would be needed to further limit false positive
violation reports.
Changelog:
- expanded patch description based on conversation with Roberto (Mimi)
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
|
|
ima_rdwr_violation_check is called for every file openning.
The function checks the policy even when violation condition
is not met. It causes unnecessary policy checking.
This patch does policy checking only if violation condition is met.
Changelog:
- check writecount is greater than zero (Mimi)
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
|
|
Newer versions of SMACK introduced following security xattrs:
SMACK64EXEC, SMACK64TRANSMUTE and SMACK64MMAP.
To protect these xattrs, this patch includes them in the HMAC
calculation. However, for backwards compatibility with existing
labeled filesystems, including these xattrs needs to be
configurable.
Changelog:
- Add SMACK dependency on new option (Mimi)
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
|
|
Using HMAC version limits the posibility to arbitrarily add new
attributes such as SMACK64EXEC to the hmac calculation.
This patch replaces hmac version with attribute mask.
Desired attributes can be enabled with configuration parameter.
It allows to build kernels which works with previously labeled
filesystems.
Currently supported attribute is 'fsuuid' which is equivalent of
the former version 2.
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
|
|
Even though a new xattr will only be appraised on the next access,
set the DIGSIG flag to prevent a signature from being replaced with
a hash on file close.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
|
|
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
"This pull request is later than I'd have liked because I was waiting
for some performance data to help finally justify sending the
long-standing dm-crypt cpu scalability improvements upstream.
Unfortunately we came up short, so those dm-crypt changes will
continue to wait, but it seems we're not far off.
. Add dm_accept_partial_bio interface to DM core to allow DM targets
to only process a portion of a bio, the remainder being sent in the
next bio. This enables the old dm snapshot-origin target to only
split write bios on chunk boundaries, read bios are now sent to the
origin device unchanged.
. Add DM core support for disabling WRITE SAME if the underlying SCSI
layer disables it due to command failure.
. Reduce lock contention in DM's bio-prison.
. A few small cleanups and fixes to dm-thin and dm-era"
* tag 'dm-3.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: update discard_granularity to reflect the thin-pool blocksize
dm bio prison: implement per bucket locking in the dm_bio_prison hash table
dm: remove symbol export for dm_set_device_limits
dm: disable WRITE SAME if it fails
dm era: check for a non-NULL metadata object before closing it
dm thin: return ENOSPC instead of EIO when error_if_no_space enabled
dm thin: cleanup noflush_work to use a proper completion
dm snapshot: do not split read bios sent to snapshot-origin target
dm snapshot: allocate a per-target structure for snapshot-origin target
dm: introduce dm_accept_partial_bio
dm: change sector_count member in clone_info from sector_t to unsigned
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull more PCI updates from Bjorn Helgaas:
"Here are some more things I'd like to see in v3.16-rc1:
- DMA alias iterator, part of some work to fix IOMMU issues
- MVEBU, Tegra, DesignWare changes that I forgot to include before
- Some whitespace code cleanup
Details:
IOMMU
- Add DMA alias iterator (Alex Williamson)
- Add DMA alias quirks for ASMedia, ITE, Tundra bridges (Alex Williamson)
- Add DMA alias quirks for Marvell, Ricoh devices (Alex Williamson)
- Add DMA alias quirk for HighPoint devices (Jérôme Carretero)
MSI
- Fix leak in free_msi_irqs() (Alexei Starovoitov)
Marvell MVEBU
- Remove unnecessary use of 'conf_lock' spinlock (Andrew Murray)
- Avoid setting an undefined window size (Jason Gunthorpe)
- Allow several windows with the same target/attribute (Thomas Petazzoni)
- Split PCIe BARs into multiple MBus windows when needed (Thomas Petazzoni)
- Fix off-by-one in the computed size of the mbus windows (Willy Tarreau)
NVIDIA Tegra
- Use new OF interrupt mapping when possible (Lucas Stach)
Synopsys DesignWare
- Remove unnecessary use of 'conf_lock' spinlock (Andrew Murray)
- Use new OF interrupt mapping when possible (Lucas Stach)
- Split Exynos and i.MX bindings (Lucas Stach)
- Fix comment for setting number of lanes (Mohit Kumar)
- Fix iATU programming for cfg1, io and mem viewport (Mohit Kumar)
Miscellaneous
- EXPORT_SYMBOL cleanup (Ryan Desfosses)
- Whitespace cleanup (Ryan Desfosses)
- Merge multi-line quoted strings (Ryan Desfosses)"
* tag 'pci-v3.16-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (21 commits)
PCI: Add function 1 DMA alias quirk for HighPoint RocketRaid 642L
PCI/MSI: Fix memory leak in free_msi_irqs()
PCI: Merge multi-line quoted strings
PCI: Whitespace cleanup
PCI: Move EXPORT_SYMBOL so it immediately follows function/variable
PCI: Add bridge DMA alias quirk for ITE bridge
PCI: designware: Split Exynos and i.MX bindings
PCI: Add bridge DMA alias quirk for ASMedia and Tundra bridges
PCI: Add support for PCIe-to-PCI bridge DMA alias quirks
PCI: Add function 1 DMA alias quirk for Marvell devices
PCI: Add function 0 DMA alias quirk for Ricoh devices
PCI: Add support for DMA alias quirks
PCI: Convert pci_dev_flags definitions to bit shifts
PCI: Add DMA alias iterator
PCI: mvebu: Use '%pa' for printing 'phys_addr_t' type
PCI: mvebu: Remove unnecessary use of 'conf_lock' spinlock
PCI: designware: Remove unnecessary use of 'conf_lock' spinlock
PCI: designware: Use new OF interrupt mapping when possible
PCI: designware: Fix iATU programming for cfg1, io and mem viewport
PCI: designware: Fix comment for setting number of lanes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are fixups on top of the previous PM+ACPI pull request,
regression fixes (ACPI hotplug, cpufreq ppc-corenet), other bug fixes
(ACPI reset, cpufreq), new PM trace points for system suspend
profiling and a copyright notice update.
Specifics:
- I didn't remember correctly that the Hans de Goede's ACPI video
patches actually didn't flip the video.use_native_backlight
default, although we had discussed that and decided to do that.
Since I said we would do that in the previous PM+ACPI pull request,
make that change for real now.
- ACPI bus check notifications for PCI host bridges don't cause the
bus below the host bridge to be checked for changes as they should
because of a mistake in the ACPI-based PCI hotplug (ACPIPHP)
subsystem that forgets to add hotplug contexts to PCI host bridge
ACPI device objects. Create hotplug contexts for PCI host bridges
too as appropriate.
- Revert recent cpufreq commit related to the big.LITTLE cpufreq
driver that breaks arm64 builds.
- Fix for a regression in the ppc-corenet cpufreq driver introduced
during the 3.15 cycle and causing the driver to use the remainder
from do_div instead of the quotient. From Ed Swarthout.
- Resets triggered by panic activate a BUG_ON() in vmalloc.c on
systems where the ACPI reset register is located in memory address
space. Fix from Randy Wright.
- Fix for a problem with cpufreq governors that decisions made by
them may be suboptimal due to the fact that deferrable timers are
used by them for CPU load sampling. From Srivatsa S Bhat.
- Fix for a problem with the Tegra cpufreq driver where the CPU
frequency is temporarily switched to a "stable" level that is
different from both the initial and target frequencies during
transitions which causes udelay() to expire earlier than it should
sometimes. From Viresh Kumar.
- New trace points and rework of some existing trace points for
system suspend/resume profiling from Todd Brandt.
- Assorted cpufreq fixes and cleanups from Stratos Karafotis and
Viresh Kumar.
- Copyright notice update for suspend-and-cpuhotplug.txt from
Srivatsa S Bhat"
* tag 'pm+acpi-3.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / hotplug / PCI: Add hotplug contexts to PCI host bridges
PM / sleep: trace events for device PM callbacks
cpufreq: cpufreq-cpu0: remove dependency on THERMAL and REGULATOR
cpufreq: tegra: update comment for clarity
cpufreq: intel_pstate: Remove duplicate CPU ID check
cpufreq: Mark CPU0 driver with CPUFREQ_NEED_INITIAL_FREQ_CHECK flag
PM / Documentation: Update copyright in suspend-and-cpuhotplug.txt
cpufreq: governor: remove copy_prev_load from 'struct cpu_dbs_common_info'
cpufreq: governor: Be friendly towards latency-sensitive bursty workloads
PM / sleep: trace events for suspend/resume
cpufreq: ppc-corenet-cpu-freq: do_div use quotient
Revert "cpufreq: Enable big.LITTLE cpufreq driver on arm64"
cpufreq: Tegra: implement intermediate frequency callbacks
cpufreq: add support for intermediate (stable) frequencies
ACPI / video: Change the default for video.use_native_backlight to 1
ACPI: Fix bug when ACPI reset register is implemented in system memory
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED updates from Bryan Wu:
"I just found merge window is open and I'm quite busy and almost forget
to send out this pull request. Thanks Russell and Alexandre ping me
about this.
So basically we got some clean up and leds-pwm fixing patches from
Russell"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Remove duplicated OOM message for individual driver
drivers/leds: Replace __get_cpu_var use through this_cpu_ptr
leds: lp55xx: add DT bindings for LP55231
leds: 88pm860x: Fix missing refcount decrement for parent of_node
leds: 88pm860x: Use of_get_child_by_name
leds: leds-pwm: add DT support for LEDs wired to supply
leds: leds-pwm: implement PWM inversion
leds: leds-pwm: convert OF parsing code to use led_pwm_add()
leds: leds-pwm: provide a common function to setup a single led-pwm device
leds: pca9685: Remove leds-pca9685 driver
dell-led: add mic mute led interface
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight fixes from Lee Jones:
"This merely contains some very basic build/run-time bug fixes"
* tag 'backlight-for-linus-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: gpio-backlight: Fix warning when the GPIO is on a I2C chip
video/backlight: s6e63m0: Fix string type mismatch
video/backlight: LP8788 needs PWM
video/backlight: LP855X needs PWM
video/pxa: LCD_CORGI needs BACKLIGHT_CLASS_DEVICE
video/backlight: LM3630A needs PWM
|
|
This patch fixes a NULL pointer dereference regression bug that was
introduced with:
commit 1e1110c43b1cda9fe77fc4a04835e460550e6b3c
Author: Mikulas Patocka <mpatocka@redhat.com>
Date: Sat May 17 06:49:22 2014 -0400
target: fix memory leak on XCOPY
Now that target_put_sess_cmd() -> kref_put_spinlock_irqsave() is
called with a valid se_cmd->cmd_kref, a NULL pointer dereference
is triggered because the XCOPY passthrough commands don't have
an associated se_session pointer.
To address this bug, go ahead and checking for a NULL se_sess pointer
within target_put_sess_cmd(), and call se_cmd->se_tfo->release_cmd()
to release the XCOPY's xcopy_pt_cmd memory.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull more MFD updates from Lee Jones:
"I missed collecting these patches due to a branch/tag naming
ambiguity. Completely my own fault, as I mindlessly named a branch
and tag identically. Sorry for the fuss.
This pull-request contains some misplaced patches from Tony Lindgren
that should have been part of the initial one"
* tag 'mfd-for-linus-3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle
mfd: twl4030-power: Add support for board specific configuration
mfd: twl4030-power: Add recommended idle configuration
mfd: twl4030-power: Add generic reset configuration
mfd: twl4030-power: Fix some defines for SW_EVENTS
mfd: twl4030-power: Fix hang on reboot if sleep configuration was loaded earlier
|
|
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes for 3.16.
- fix some various compiler warnings
- make atmel-mci compile again
- fix regression for sdhci-msm"
* tag 'mmc-v3.16-2' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: simplify SDHCI Kconfig dependencies
mmc: omap: don't select TPS65010
mmc: mvsdio: avoid compiler warning
mmc: atmel-mci: incude asm/cacheclush.h
mmc: sdhci-msm: Fix fallout from sdhci refactoring
mmc: usdhi6rol0: fix compiler warnings
|
|
Pull drm updates from Dave Airlie:
"This is the main drm merge window pull request, changes all over the
place, mostly normal levels of churn.
Highlights:
Core drm:
More cleanups, fix race on connector/encoder naming, docs updates,
object locking rework in prep for atomic modeset
i915:
mipi DSI support, valleyview power fixes, cursor size fixes,
execlist refactoring, vblank improvements, userptr support, OOM
handling improvements
radeon:
GPUVM tuning and large page size support, gart fixes, deep color
HDMI support, HDMI audio cleanups
nouveau:
- displayport rework should fix lots of issues
- initial gk20a support
- gk110b support
- gk208 fixes
exynos:
probe order fixes, HDMI changes, IPP consolidation
msm:
debugfs updates, misc fixes
ast:
ast2400 support, sync with UMS driver
tegra:
cleanups, hdmi + hw cursor for Tegra 124.
panel:
fixes existing panels add some new ones.
ipuv3:
moved from staging to drivers/gpu"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (761 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
|
|
When running RHEL6 userspace on a current upstream kernel, "ip link"
fails to show VF information.
The reason is a kernel<->userspace API change introduced by commit
88c5b5ce5cb57 ("rtnetlink: Call nlmsg_parse() with correct header length"),
after which the kernel does not see iproute2's IFLA_EXT_MASK attribute
in the netlink request.
iproute2 adjusted for the API change in its commit 63338dca4513
("libnetlink: Use ifinfomsg instead of rtgenmsg in rtnl_wilddump_req_filter").
The problem has been noticed before:
http://marc.info/?l=linux-netdev&m=136692296022182&w=2
(Subject: Re: getting VF link info seems to be broken in 3.9-rc8)
We can do better than tell those with old userspace to upgrade. We can
recognize the old iproute2 in the kernel by checking the netlink message
length. Even when including the IFLA_EXT_MASK attribute, its netlink
message is shorter than struct ifinfomsg.
With this patch "ip link" shows VF information in both old and new
iproute2 versions.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to a problem observed when losing a FIN segment that does not
contain data. In such situations, TLP is unable to recover from
*any* tail loss and instead adds at least PTO ms to the
retransmission process, i.e., RTO = RTO + PTO.
Signed-off-by: Per Hurtig <per.hurtig@kau.se>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fugang Duan says:
====================
net: fec: Enable Software TSO to improve the tx performance
Add SG and software TSO support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board, running iperf tcp tests shows:
* 82% improvement comparing with NO SG & TSO patch
$ ethtool -K eth0 sg on
$ ethtool -K eth0 tso on
[ 3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 181 MBytes 506 Mbits/sec
* cpu loading is 30%
$ ethtool -K eth0 sg off
$ ethtool -K eth0 tso off
[ 3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 99.5 MBytes 278 Mbits/sec
FEC HW support IP header and TCP/UDP hw checksum, support multi buffer descriptor transfer
one frame, but don't support HW TSO. And imx6q/dl SOC FEC Gbps speed has HW bus Bandwidth
limitation (400Mbps ~ 700Mbps), imx6sx SOC FEC Gbps speed has no HW bandwidth limitation.
The patch set just enable TSO feature, which is done following the mv643xx_eth driver.
Test result analyze:
imx6dl sabresd board: there have 82% improvement, since imx6dl FEC HW has bandwidth limitation,
the performance with SW TSO is a milestone.
Addition test:
imx6sx sdb board:
upstream still don't support imx6sx due to some patches being upstream... they use same FEC IP.
Use the SW TSO patches test imx6sx sdb board in internal kernel tree:
No SW TSO patch: tx bandwidth 840Mbps, cpu loading is 100%.
SW TSO patch: tx bandwidth 942Mbps, cpu loading is 65%.
It means the patch set have great improvement for imx6sx FEC performance.
V2:
* From Frank Li's suggestion:
Change the API "fec_enet_txdesc_entry_free" name to "fec_enet_get_free_txdesc_num".
* Summary David Laight and Eric Dumazet's thoughts:
RX BD entry number change to 256.
* From ezequiel's suggestion:
Follow the latest TSO fixes from his solution to rework the queue stop/wake-up.
Avoid unmapping the TSO header buffers.
* From Eric Dumazet's suggestion:
Avoid more bytes copy, just copying the unaligned part of the payload into first
descriptor. The suggestion will bring more complex for the driver, and imx6dl FEC
DMA need 16 bytes alignment, but cpu loading is not problem that cpu loading is
30%, the current performance is so better. Later chip like imx6sx Gigbit FEC DMA
support byte alignment, so there don't exist memory copy. So, the V2 version drop
the suggestion.
Anyway, thanks for Eric's response and suggestion.
V3:
* From David Laight's feedback:
Decide to drop RX BD entry number change for the SW TSO patch set.
I will generate one separate patch to increase RX BDs entry for interrupt coalescing feature which
will be supported in my later patch set.
V4:
* From David Laight's feedback:
Remove the conditional in .fec_enet_get_bd_index().
V5:
* Patch #4 update:
From David Laight's feedback:
"expect fec_enet_get_free_txdesc_num() to return one less than it does currently."
Change the function:
Return space available, 0..size-1. it always leave one free entry. Which is same as linux circ_buf.
Thanks for Eric and ezequiel's help and idea.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add software TSO support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board, running iperf tcp tests shows:
- 16.2% improvement comparing with FEC SG patch
- 82% improvement comparing with NO SG & TSO patch
$ ethtool -K eth0 tso on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 181 MBytes 506 Mbits/sec
During the testing, CPU loading is 30%.
Since imx6dl FEC Bandwidth is limited to SOC system bus bandwidth, the
performance with SW TSO is a milestone.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Scatter/gather support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board:
Running iperf tests shows a 55.4% improvement.
$ ethtool -K eth0 sg off
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 99.5 MBytes 278 Mbits/sec
$ ethtool -K eth0 sg on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52617 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 154 MBytes 432 Mbits/sec
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support SG, software TSO, let's increase BD entry number.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to enhance the code readable, let's factorize the
feature list.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IP header checksum is calcalated by network layer in default.
To support software TSO, it is better to use HW calculate the
IP header checksum.
FEC hw checksum feature request the checksum field in frame
is zero, otherwise the calculative CRC is not correct.
For segmentated TCP packet, HW calculate the IP header checksum again,
it doesn't bring any impact. For SW TSO, HW calculated checksum bring
better performance.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the code more readable and easy to support other features like
SG, TSO, moving the common transmit function to one api.
And the patch also factorize the getting BD index to it own function.
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some fields in "struct net_bridge" aren't available when compiling the
kernel without IPv6 support. Therefore adding a check/macro to skip the
complaining code sections in that case.
Introduced by 2cd4143192e8c60f66cb32c3a30c76d0470a372d
("bridge: memorize and export selected IGMP/MLD querier port")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"New smatch warnings:
net/bridge/br_multicast.c:1368 br_ip6_multicast_query() error:
we previously assumed 'group' could be null (see line 1349)"
In the rare (sort of broken) case of a query having a Maximum
Response Delay of zero, we could create a potential null pointer
dereference.
Fixing this by skipping the multicast specific MLD Query parsing again
if no multicast group address is available.
Introduced by dc4eb53a996a78bfb8ea07b47423ff5a3aadc362
("bridge: adhere to querier election mechanism specified by RFCs")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With some specific configuration (VT6105M on Soekris 5510 and depending
on the device at the other end), fragmented packets were not transmitted
when forcing 100 full-duplex with autoneg disable.
This fix now write full-duplex chips register when forcing full or
half-duplex not only when autoneg is enable.
Signed-off-by: François Cachereul <f.cachereul@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"This the bunch that sat in -next + lock_parent() fix. This is the
minimal set; there's more pending stuff.
In particular, I really hope to get acct.c fixes merged this cycle -
we need that to deal sanely with delayed-mntput stuff. In the next
pile, hopefully - that series is fairly short and localized
(kernel/acct.c, fs/super.c and fs/namespace.c). In this pile: more
iov_iter work. Most of prereqs for ->splice_write with sane locking
order are there and Kent's dio rewrite would also fit nicely on top of
this pile"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (70 commits)
lock_parent: don't step on stale ->d_parent of all-but-freed one
kill generic_file_splice_write()
ceph: switch to iter_file_splice_write()
shmem: switch to iter_file_splice_write()
nfs: switch to iter_splice_write_file()
fs/splice.c: remove unneeded exports
ocfs2: switch to iter_file_splice_write()
->splice_write() via ->write_iter()
bio_vec-backed iov_iter
optimize copy_page_{to,from}_iter()
bury generic_file_aio_{read,write}
lustre: get rid of messing with iovecs
ceph: switch to ->write_iter()
ceph_sync_direct_write: stop poking into iov_iter guts
ceph_sync_read: stop poking into iov_iter guts
new helper: copy_page_from_iter()
fuse: switch to ->write_iter()
btrfs: switch to ->write_iter()
ocfs2: switch to ->write_iter()
xfs: switch to ->write_iter()
...
|
|
Yuval Mintz says:
====================
bnx2x: Bug fixes patch series
This patch series contains various bug fixes - 2 link related fixes,
one sriov-related issue and an additional fix for a theoretical bug
on new boards.
Please consider applying these patches to `net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A malicious VF might try to starve the other VFs & PF by creating
contineous doorbell floods. In order to negate this, HW has a threshold of
doorbells per client, which will stop the client doorbells from arriving
if crossed.
The threshold currently configured for VFs is too low - under extreme traffic
scenarios, it's possible for a VF to reach the threshold and thus for its
fastpath to stop working.
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If L2FW utilized by the UNDI driver has the same version number as that
of the regular FW, a driver loading after UNDI and receiving an uncommon
answer from management will mistakenly assume the loaded FW matches its
own requirement and try to exist the flow via FLR.
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the phy access mode even in case of link-flap avoidance.
Signed-off-by: Yaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This avoids clearing the RX polarity setting in KR mode when polarity lane
is swapped, as otherwise this will result in failed link.
Signed-off-by: Yaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Consider the scenario:
For a TCP-style socket, while processing the COOKIE_ECHO chunk in
sctp_sf_do_5_1D_ce(), after it has passed a series of sanity check,
a new association would be created in sctp_unpack_cookie(), but afterwards,
some processing maybe failed, and sctp_association_free() will be called to
free the previously allocated association, in sctp_association_free(),
sk_ack_backlog value is decremented for this socket, since the initial
value for sk_ack_backlog is 0, after the decrement, it will be 65535,
a wrap-around problem happens, and if we want to establish new associations
afterward in the same socket, ABORT would be triggered since sctp deem the
accept queue as full.
Fix this issue by only decrementing sk_ack_backlog for associations in
the endpoint's list.
Fix-suggested-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_hwmon_device_register_with_groups instead of
the old-style manual attributes and hwmon device registration.
Also, unroll the attribute group macros for better code
readability.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Move atxp1_id and atxp1_driver to proper place to avoid forward declaration.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for Sensirion SHTC1 and compatible temperature and humidity
sensors.
Signed-off-by: Tomas Pop <tomas.pop@sensirion.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Per Dalén <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Generic detection leads to too many false positives, so drop it. FWIW
sensors-detect does not have such generic detection. If the user wants
to force the driver to bind to a not yet supported chip, he/she can
still do so using sysfs attribute new_device.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
All devices supported by ina2xx are bidirectional and report the
measured shunt voltage and power values as a signed 16 bit, but the
current driver implementation caches all registers as u16, leading
to an incorrect sign extension when reporting to userspace in
ina2xx_get_value().
This patch fixes the problem by casting the signed registers to s16.
Tested on an INA219.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The connection struct with nodeid 0 is the listening socket,
not a connection to another node. The sctp resend function
was not checking that the nodeid was valid (non-zero), so it
would mistakenly get and resend on the listening connection
when nodeid was zero.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: David Teigland <teigland@redhat.com>
|
|
Fix this dependency on the locking tree's smp_mb*() API changes:
kernel/sched/idle.c:247:3: error: implicit declaration of function ‘smp_mb__after_atomic’ [-Werror=implicit-function-declaration]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
* pm-sleep:
PM / sleep: trace events for device PM callbacks
PM / sleep: trace events for suspend/resume
|
|
* pm-cpufreq:
cpufreq: cpufreq-cpu0: remove dependency on THERMAL and REGULATOR
cpufreq: tegra: update comment for clarity
cpufreq: intel_pstate: Remove duplicate CPU ID check
cpufreq: Mark CPU0 driver with CPUFREQ_NEED_INITIAL_FREQ_CHECK flag
cpufreq: governor: remove copy_prev_load from 'struct cpu_dbs_common_info'
cpufreq: governor: Be friendly towards latency-sensitive bursty workloads
cpufreq: ppc-corenet-cpu-freq: do_div use quotient
Revert "cpufreq: Enable big.LITTLE cpufreq driver on arm64"
cpufreq: Tegra: implement intermediate frequency callbacks
cpufreq: add support for intermediate (stable) frequencies
|
|
* acpi-general:
ACPI: Fix bug when ACPI reset register is implemented in system memory
* acpi-video:
ACPI / video: Change the default for video.use_native_backlight to 1
|
|
* acpi-hotplug:
ACPI / hotplug / PCI: Add hotplug contexts to PCI host bridges
|
|
do_posix_clock_monotonic_gettime() is a leftover from the initial
posix timer implementation which maps to ktime_get_ts() and returns
the monotonic time in a timespec.
Use ktime based ktime_get() and use the ktime_delta_us() function to
calculate the delta instead of open coding the timespec math.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
do_posix_clock_monotonic_gettime() is a leftover from the initial
posix timer implementation which maps to ktime_get_ts().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch will verify the pin's coverter selection for an active stream
when an unsol event reports this pin becomes available again after a display
mode change or hot-plug event.
For Haswell+ and Valleyview: display mode change or hot-plug can change the
transcoder:port connection and make all the involved audio pins share the 1st
converter. So the stream using 1st convertor will flow to multiple pins
but active streams using other converters will fail. This workaround
is to assure the pin selects the right conveter and an assigned converter is
not shared by other unused pins.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
struct for all platform.
Cancel the optimization of compiler for struct snd_compr_avail
which size will be 0x1c in 32bit kernel while 0x20 in 64bit
kernel under the optimizer. That will make compaction between
32bit and 64bit. So add packed to fix the size of struct
snd_compr_avail to 0x1c for all platform.
Signed-off-by: Zhang Dongxing <dongxing.zhang@intel.com>
Signed-off-by: xiaoming wang <xiaoming.wang@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
These defconfigs contain the CONFIG_M25P80 symbol, which is now
dependent on the MTD_SPI_NOR symbol. Add CONFIG_MTD_SPI_NOR to the
relevant defconfigs.
At the same time, drop the now-nonexistent CONFIG_MTD_CHAR symbol.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: adi-buildroot-devel@lists.sourceforge.net
Cc: linux-kernel@vger.kernel.org
|
|
We have a number of front-end drivers for SDHCI_PLTFM, some of them
use 'select MMC_SDHCI_PLTFM', others use 'depends on'. This is
inconsistent and confusing, and in one case has also led to a
build error because of incomplete dependencies:
warning: (MMC_SDHCI_PXAV3 && MMC_SDHCI_PXAV2 && MMC_SDHCI_BCM_KONA) selects MMC_SDHCI_PLTFM which has unmet direct dependencies (MMC && MMC_SDHCI)
drivers/built-in.o: In function `sdhci_sirf_resume':
:(.text+0xaaacb4): undefined reference to `sdhci_resume_host'
drivers/built-in.o: In function `sdhci_sirf_suspend':
:(.text+0xaaacf8): undefined reference to `sdhci_suspend_host'
drivers/built-in.o: In function `sdhci_sirf_probe':
:(.text+0xaaaf44): undefined reference to `sdhci_add_host'
:(.text+0xaaaf50): undefined reference to `sdhci_remove_host'
This changes Kconfig to use 'depends on MMC_SDHCI_PLTFM' for all these
cases, to fix the build error and make the logic more logical.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The MMC host driver should not select the pmic driver, since that
may have other dependencies, notably i2c in this case. It's not
clear what the exact requirement of the driver is, but to preserve
the behavior, this patch changes the 'select' into 'depends on',
meaning you now have to turn on TPS65010 explicitly and then
MMC_OMAP.
Found during randconfig build testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
gcc correctly points out that hw_state can be used uninitially
in the mvsd_setup_data() function. This rearranges the function
to ensure it always contains a proper value.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Chris Ball <chris@printf.net>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: linux-mmc@vger.kernel.org
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This avoids a build error due to the use of flush_dcache_page.
drivers/mmc/host/atmel-mci.c: In function 'atmci_read_data_pio':
drivers/mmc/host/atmel-mci.c:1870:5: error: implicit declaration of function 'flush_dcache_page' [-Werror=implicit-function-declaration]
flush_dcache_page(sg_page(sg));
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sdhci core was refactored recently and some of those
refactorings required changes in every sdhci platform driver.
Those updates happened around the same time as when the msm
driver was merged so the refactorings missed the msm driver.
Hook in the basic library functions so that we can boot apq8074
dragonboards again instead of crashing when we try to jump to
NULL function pointers.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Georgi Djakov <gdjakov@mm-sol.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Georgi Djakov <gdjakov@mm-sol.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix a number of wrong print formats.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The rule to create the final images uses a zImage.% pattern.
Unfortunately, this also matches the names of the zImage.*.lds linker
scripts, which appear as a dependency of the final images. This somehow
worked when $(srctree) used to be an absolute path, but now the pattern
matches too much. List only the images from $(image-y) as the target of
the rule, to avoid the circular dependency.
Reported-and-tested-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
Commit dd34c37aa3e (gpio: of: Allow -gpio suffix for property names)
added parsing for both -gpio and -gpios suffix but also changed
the handling for deferred probe unintentionally. Because of the
looping the second name will now return -ENOENT instead of
-EPROBE_DEFER. Fix the issue by breaking out of the loop if
-EPROBE_DEFER is encountered.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Dentry that had been through (or into) __dentry_kill() might be seen
by shrink_dentry_list(); that's normal, it'll be taken off the shrink
list and freed if __dentry_kill() has already finished. The problem
is, its ->d_parent might be pointing to already freed dentry, so
lock_parent() needs to be careful.
We need to check that dentry hasn't already gone into __dentry_kill()
*and* grab rcu_read_lock() before dropping ->d_lock - the latter makes
sure that whatever we see in ->d_parent after dropping ->d_lock it
won't be freed until we drop rcu_read_lock().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Backmerge of dcache.c changes from mainline. It's that, or complete
rebase...
Conflicts:
fs/splice.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
no callers left
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
ocfs2 was using a bunch of splice.c guts...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
iter_file_splice_write() - a ->splice_write() instance that gathers the
pipe buffers, builds a bio_vec-based iov_iter covering those and feeds
it to ->write_iter(). A bunch of simple cases coverted to that...
[AV: fixed the braino spotted by Cyrill]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Main excitement is a virtio_scsi fix for alloc holding spinlock on the
abort path, which I refuse to CC stable since (1) I discovered it
myself, and (2) it's been there forever with no reports"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_scsi: don't call virtqueue_add_sgs(... GFP_NOIO) holding spinlock.
virtio-rng: fixes for device registration/unregistration
virtio-rng: fix boot with virtio-rng device
virtio-rng: support multiple virtio-rng devices
virtio_ccw: introduce device_lost in virtio_ccw_device
virtio: virtio_break_device() to mark all virtqueues broken.
|
|
Pull vhost infrastructure updates from Michael S. Tsirkin:
"This reworks vhost core dropping unnecessary RCU uses in favor of VQ
mutexes which are used on fast path anyway. This fixes worst-case
latency for users which change the memory mappings a lot. Memory
allocation for vhost-net now supports fallback on vmalloc (same as for
vhost-scsi) this makes it possible to create the device on systems
where memory is very fragmented, with slightly lower performance"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: move memory pointer to VQs
vhost: move acked_features to VQs
vhost: replace rcu with mutex
vhost-net: extend device allocation to vmalloc
|
|
Pull arch/tile changes from Chris Metcalf:
"These mostly just address smaller issues reported to me"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch: tile: kernel: unaligned.c: Cleaning up uninitialized variables
drivers/tty/hvc/hvc_tile.c: use PTR_ERR_OR_ZERO
replace strict_strto* call with kstrto*
tile: Update comments for generic idle conversion
tile: cleanup the comment in init_pgprot
tile: use BOOTMEM_DEFAULT instead of magic number 0 for reserve_bootmem flags
|
|
Commit 2749a2f26a7c (powerpc/book3s: Fix machine check handling for
unhandled errors) introduced a few ABIv2 issues.
We can maintain ABIv1 and ABIv2 compatibility by branching to the
function rather than the dot symbol.
Fixes: 2749a2f26a7c ("powerpc/book3s: Fix machine check handling for unhandled errors")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Most of this is cleaning up various driver sysfs permissions so we can
re-add the perm check (we unified the module param and sysfs checks,
but the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args()"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: set nx before marking module MODULE_STATE_COMING.
samples/kobject/: avoid world-writable sysfs files.
drivers/hid/hid-picolcd_fb: avoid world-writable sysfs files.
drivers/staging/speakup/: avoid world-writable sysfs files.
drivers/regulator/virtual: avoid world-writable sysfs files.
drivers/scsi/pm8001/pm8001_ctl.c: avoid world-writable sysfs files.
drivers/hid/hid-lg4ff.c: avoid world-writable sysfs files.
drivers/video/fbdev/sm501fb.c: avoid world-writable sysfs files.
drivers/mtd/devices/docg3.c: avoid world-writable sysfs files.
speakup: fix incorrect perms on speakup_acntsa.c
cpumask.h: silence warning with -Wsign-compare
Documentation: Update kernel-parameters.tx
param: hand arguments after -- straight to init
modpost: Fix resource leak in read_dump()
|
|
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1d8faf48c7 (net/core: Add VF link state control) added VF link state
control to the netlink VF nested structure, but failed to add a proper entry
for the new structure into the VF policy table. Add the missing entry so
the table and the actual data copied into the netlink nested struct are in
sync.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Print the device address, the register number and the PHY ID for
which the MDIO read operation failed
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DRR scheduler requires that items on the active list are work
conserving, i.e. do not hold on to skbs for throttling purposes, etc.
Attaching e.g. tbf renders DRR useless because all other classes on the
active list are delayed as well.
So, warn users that this configuration won't work as expected; we
already do this in couple of other qdiscs, see e.g.
commit b00355db3f88d96810a60011a30cfb2c3469409d
('pkt_sched: sch_hfsc: sch_htb: Add non-work-conserving warning handler')
The 'const' change is needed to avoid compiler warning ("discards 'const'
qualifier from pointer target type").
tested with:
drr_hier() {
parent=$1
classes=$2
for i in $(seq 1 $classes); do
classid=$parent$(printf %x $i)
tc class add dev eth0 parent $parent classid $classid drr
tc qdisc add dev eth0 parent $classid tbf rate 64kbit burst 256kbit limit 64kbit
done
}
tc qdisc add dev eth0 root handle 1: drr
drr_hier 1: 32
tc filter add dev eth0 protocol all pref 1 parent 1: handle 1 flow hash keys dst perturb 1 divisor 32
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tom Herbert says:
====================
net: Checksum offload changes - Part IV
I am working on overhauling RX checksum offload. Goals of this effort
are:
- Specify what exactly it means when driver returns CHECKSUM_UNNECESSARY
- Preserve CHECKSUM_COMPLETE through encapsulation layers
- Don't do skb_checksum more than once per packet
- Unify GRO and non-GRO csum verification as much as possible
- Unify the checksum functions (checksum_init)
- Simply code
What is in this fourth patch set:
- Preserve CHECKSUM_COMPLETE instead of changing it to
CHECKSUM_UNNECESSARY. This allows correct reuse in validating multiple
csums in a packet.
- When SW needs to compute the packet checksum, save it as
CHECKSUM_COMPLETE. Also mark that checksum was compute by SW.
- Add skb_gro_postpull_rcsum to udp and vxlan to make GRO work with
CHECKSUM_COMPLETE.
v2: Removed patch setting skb_encapsulation when validating checksum
in tcp_gro_receive
Please review carefully and test if possible, mucking with basic
checksum functions is always a little precarious :-)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to gro_postpull_rcsum for GRO to work with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In skb_checksum complete, if we need to compute the checksum for the
packet (via skb_checksum) save the result as CHECKSUM_COMPLETE.
Subsequent checksum verification can use this.
Also, added csum_complete_sw flag to distinguish between software and
hardware generated checksum complete, we should always be able to trust
the software computation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when the first checksum in a packet is validated using
CHECKSUM_COMPLETE, ip_summed is overwritten to be CHECKSUM_UNNECESSARY
so that any subsequent checksums in the packet are not correctly
validated.
This patch adds csum_valid flag in sk_buff and uses that to indicate
validated checksum instead of setting CHECKSUM_UNNECESSARY. The bit
is set accordingly in the skb_checksum_validate_* functions. The flag
is checked in skb_checksum_complete, so that validation is communicated
between checksum_init and checksum_complete sequence in TCP and UDP.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Shahed Shaikh says:
====================
This series contains an enhancement in the area of firmware minidump collection
and optimization of ring count validation function.
Please apply this series to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Check interrupt mode at the start of qlcnic_set_channels().
- Do not validate ring count if they are not going to change.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pre-allocate the physically contiguous DMA buffer used for
minidump collection at driver load time, rather than at
run time, to minimize allocation failures. Driver will allocate
the buffer at load time if PEX DMA support capability is indicated
by the adapter.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the following sparse warnings:
net/ipv4/ip_tunnel.c:245:53: warning: restricted __be16 degrades to integer
net/ipv4/ip_vti.c:321:19: warning: incorrect type in assignment (different base types)
net/ipv4/ip_vti.c:321:19: expected restricted __be16 [addressable] [assigned] [usertype] i_flags
net/ipv4/ip_vti.c:321:19: got int
net/ipv4/ip_vti.c:447:24: warning: incorrect type in assignment (different base types)
net/ipv4/ip_vti.c:447:24: expected restricted __be16 [usertype] i_flags
net/ipv4/ip_vti.c:447:24: got int
Since VTI_ISVTI is always used with ip_tunnel_parm->i_flags (which is __be16),
we can __force cast VTI_ISVTI to __be16 in header file.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We recently change the kzalloc() to devm_kzalloc() so freeing "ctlr"
here could lead to a double free.
Fixes: e194312854ed ('drivers: net: davinci_cpdma: Convert kzalloc() to devm_kzalloc().')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a typo here so we return directly instead of unwinding.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
adds the device managed APIs so that no need worry about
freeing the resources.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sparse complained about this bogus extern on definition of
a function.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a description of eBPFs instruction encoding in order
to bring the documentation in line with the implementation.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the term eBPF is used anyway on mailing list discussions, lets
also document that in the main BPF documentation file and replace a
couple of occurrences with eBPF terminology to be more clear.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexey gave a AddressSanitizer[1] report that finally gave a good hint
at where was the origin of various problems already reported by Dormando
in the past [2]
Problem comes from the fact that UDP can have a lockless TX path, and
concurrent threads can manipulate sk_dst_cache, while another thread,
is holding socket lock and calls __sk_dst_set() in
ip4_datagram_release_cb() (this was added in linux-3.8)
It seems that all we need to do is to use sk_dst_check() and
sk_dst_set() so that all the writers hold same spinlock
(sk->sk_dst_lock) to prevent corruptions.
TCP stack do not need this protection, as all sk_dst_cache writers hold
the socket lock.
[1]
https://code.google.com/p/address-sanitizer/wiki/AddressSanitizerForKernel
AddressSanitizer: heap-use-after-free in ipv4_dst_check
Read of size 2 by thread T15453:
[<ffffffff817daa3a>] ipv4_dst_check+0x1a/0x90 ./net/ipv4/route.c:1116
[<ffffffff8175b789>] __sk_dst_check+0x89/0xe0 ./net/core/sock.c:531
[<ffffffff81830a36>] ip4_datagram_release_cb+0x46/0x390 ??:0
[<ffffffff8175eaea>] release_sock+0x17a/0x230 ./net/core/sock.c:2413
[<ffffffff81830882>] ip4_datagram_connect+0x462/0x5d0 ??:0
[<ffffffff81846d06>] inet_dgram_connect+0x76/0xd0 ./net/ipv4/af_inet.c:534
[<ffffffff817580ac>] SYSC_connect+0x15c/0x1c0 ./net/socket.c:1701
[<ffffffff817596ce>] SyS_connect+0xe/0x10 ./net/socket.c:1682
[<ffffffff818b0a29>] system_call_fastpath+0x16/0x1b
./arch/x86/kernel/entry_64.S:629
Freed by thread T15455:
[<ffffffff8178d9b8>] dst_destroy+0xa8/0x160 ./net/core/dst.c:251
[<ffffffff8178de25>] dst_release+0x45/0x80 ./net/core/dst.c:280
[<ffffffff818304c1>] ip4_datagram_connect+0xa1/0x5d0 ??:0
[<ffffffff81846d06>] inet_dgram_connect+0x76/0xd0 ./net/ipv4/af_inet.c:534
[<ffffffff817580ac>] SYSC_connect+0x15c/0x1c0 ./net/socket.c:1701
[<ffffffff817596ce>] SyS_connect+0xe/0x10 ./net/socket.c:1682
[<ffffffff818b0a29>] system_call_fastpath+0x16/0x1b
./arch/x86/kernel/entry_64.S:629
Allocated by thread T15453:
[<ffffffff8178d291>] dst_alloc+0x81/0x2b0 ./net/core/dst.c:171
[<ffffffff817db3b7>] rt_dst_alloc+0x47/0x50 ./net/ipv4/route.c:1406
[< inlined >] __ip_route_output_key+0x3e8/0xf70
__mkroute_output ./net/ipv4/route.c:1939
[<ffffffff817dde08>] __ip_route_output_key+0x3e8/0xf70 ./net/ipv4/route.c:2161
[<ffffffff817deb34>] ip_route_output_flow+0x14/0x30 ./net/ipv4/route.c:2249
[<ffffffff81830737>] ip4_datagram_connect+0x317/0x5d0 ??:0
[<ffffffff81846d06>] inet_dgram_connect+0x76/0xd0 ./net/ipv4/af_inet.c:534
[<ffffffff817580ac>] SYSC_connect+0x15c/0x1c0 ./net/socket.c:1701
[<ffffffff817596ce>] SyS_connect+0xe/0x10 ./net/socket.c:1682
[<ffffffff818b0a29>] system_call_fastpath+0x16/0x1b
./arch/x86/kernel/entry_64.S:629
[2]
<4>[196727.311203] general protection fault: 0000 [#1] SMP
<4>[196727.311224] Modules linked in: xt_TEE xt_dscp xt_DSCP macvlan bridge coretemp crc32_pclmul ghash_clmulni_intel gpio_ich microcode ipmi_watchdog ipmi_devintf sb_edac edac_core lpc_ich mfd_core tpm_tis tpm tpm_bios ipmi_si ipmi_msghandler isci igb libsas i2c_algo_bit ixgbe ptp pps_core mdio
<4>[196727.311333] CPU: 17 PID: 0 Comm: swapper/17 Not tainted 3.10.26 #1
<4>[196727.311344] Hardware name: Supermicro X9DRi-LN4+/X9DR3-LN4+/X9DRi-LN4+/X9DR3-LN4+, BIOS 3.0 07/05/2013
<4>[196727.311364] task: ffff885e6f069700 ti: ffff885e6f072000 task.ti: ffff885e6f072000
<4>[196727.311377] RIP: 0010:[<ffffffff815f8c7f>] [<ffffffff815f8c7f>] ipv4_dst_destroy+0x4f/0x80
<4>[196727.311399] RSP: 0018:ffff885effd23a70 EFLAGS: 00010282
<4>[196727.311409] RAX: dead000000200200 RBX: ffff8854c398ecc0 RCX: 0000000000000040
<4>[196727.311423] RDX: dead000000100100 RSI: dead000000100100 RDI: dead000000200200
<4>[196727.311437] RBP: ffff885effd23a80 R08: ffffffff815fd9e0 R09: ffff885d5a590800
<4>[196727.311451] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
<4>[196727.311464] R13: ffffffff81c8c280 R14: 0000000000000000 R15: ffff880e85ee16ce
<4>[196727.311510] FS: 0000000000000000(0000) GS:ffff885effd20000(0000) knlGS:0000000000000000
<4>[196727.311554] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4>[196727.311581] CR2: 00007a46751eb000 CR3: 0000005e65688000 CR4: 00000000000407e0
<4>[196727.311625] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
<4>[196727.311669] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
<4>[196727.311713] Stack:
<4>[196727.311733] ffff8854c398ecc0 ffff8854c398ecc0 ffff885effd23ab0 ffffffff815b7f42
<4>[196727.311784] ffff88be6595bc00 ffff8854c398ecc0 0000000000000000 ffff8854c398ecc0
<4>[196727.311834] ffff885effd23ad0 ffffffff815b86c6 ffff885d5a590800 ffff8816827821c0
<4>[196727.311885] Call Trace:
<4>[196727.311907] <IRQ>
<4>[196727.311912] [<ffffffff815b7f42>] dst_destroy+0x32/0xe0
<4>[196727.311959] [<ffffffff815b86c6>] dst_release+0x56/0x80
<4>[196727.311986] [<ffffffff81620bd5>] tcp_v4_do_rcv+0x2a5/0x4a0
<4>[196727.312013] [<ffffffff81622b5a>] tcp_v4_rcv+0x7da/0x820
<4>[196727.312041] [<ffffffff815fd9e0>] ? ip_rcv_finish+0x360/0x360
<4>[196727.312070] [<ffffffff815de02d>] ? nf_hook_slow+0x7d/0x150
<4>[196727.312097] [<ffffffff815fd9e0>] ? ip_rcv_finish+0x360/0x360
<4>[196727.312125] [<ffffffff815fda92>] ip_local_deliver_finish+0xb2/0x230
<4>[196727.312154] [<ffffffff815fdd9a>] ip_local_deliver+0x4a/0x90
<4>[196727.312183] [<ffffffff815fd799>] ip_rcv_finish+0x119/0x360
<4>[196727.312212] [<ffffffff815fe00b>] ip_rcv+0x22b/0x340
<4>[196727.312242] [<ffffffffa0339680>] ? macvlan_broadcast+0x160/0x160 [macvlan]
<4>[196727.312275] [<ffffffff815b0c62>] __netif_receive_skb_core+0x512/0x640
<4>[196727.312308] [<ffffffff811427fb>] ? kmem_cache_alloc+0x13b/0x150
<4>[196727.312338] [<ffffffff815b0db1>] __netif_receive_skb+0x21/0x70
<4>[196727.312368] [<ffffffff815b0fa1>] netif_receive_skb+0x31/0xa0
<4>[196727.312397] [<ffffffff815b1ae8>] napi_gro_receive+0xe8/0x140
<4>[196727.312433] [<ffffffffa00274f1>] ixgbe_poll+0x551/0x11f0 [ixgbe]
<4>[196727.312463] [<ffffffff815fe00b>] ? ip_rcv+0x22b/0x340
<4>[196727.312491] [<ffffffff815b1691>] net_rx_action+0x111/0x210
<4>[196727.312521] [<ffffffff815b0db1>] ? __netif_receive_skb+0x21/0x70
<4>[196727.312552] [<ffffffff810519d0>] __do_softirq+0xd0/0x270
<4>[196727.312583] [<ffffffff816cef3c>] call_softirq+0x1c/0x30
<4>[196727.312613] [<ffffffff81004205>] do_softirq+0x55/0x90
<4>[196727.312640] [<ffffffff81051c85>] irq_exit+0x55/0x60
<4>[196727.312668] [<ffffffff816cf5c3>] do_IRQ+0x63/0xe0
<4>[196727.312696] [<ffffffff816c5aaa>] common_interrupt+0x6a/0x6a
<4>[196727.312722] <EOI>
<1>[196727.313071] RIP [<ffffffff815f8c7f>] ipv4_dst_destroy+0x4f/0x80
<4>[196727.313100] RSP <ffff885effd23a70>
<4>[196727.313377] ---[ end trace 64b3f14fae0f2e29 ]---
<0>[196727.380908] Kernel panic - not syncing: Fatal exception in interrupt
Reported-by: Alexey Preobrazhensky <preobr@google.com>
Reported-by: dormando <dormando@rydia.ne>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 8141ed9fcedb2 ("ipv4: Add a socket release callback for datagram sockets")
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add lib/test_bpf.c entry to maintainers file under networking.
All changes were posted via netdev for review, so make sure
other people Cc it as well when they call get_maintainer.pl.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several instances where a pskb_copy or __pskb_copy is
immediately followed by an skb_clone.
Add a couple of new functions to allow the copy skb to be allocated
from the fclone cache and thus speed up subsequent skb_clone calls.
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes:ee45fd92c739
("sfc: Use TX PIO for sufficiently small packets")
The linux net driver uses memcpy_toio() in order to copy into
the PIO buffers.
Even on a 64bit machine this causes 32bit accesses to a write-
combined memory region.
There are hardware limitations that mean that only 64bit
naturally aligned accesses are safe in all cases.
Due to being write-combined memory region two 32bit accesses
may be coalesced to form a 64bit non 64bit aligned access.
Solution was to open-code the memory copy routines using pointers
and to only enable PIO for x86_64 machines.
Not tested on platforms other than x86_64 because this patch
disables the PIO feature on other platforms.
Compile-tested on x86 to ensure that works.
The WARN_ON_ONCE() code in the previous version of this patch
has been moved into the internal sfc debug driver as the
assertion was unnecessary in the upstream kernel code.
This bug fix applies to v3.13 and v3.14 stable branches.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Toshiaki Makita says:
====================
bridge: 802.1ad vlan protocol support
Currently bridge vlan filtering doesn't work fine with 802.1ad protocol.
Only if a bridge is configured without pvid, the bridge receives only
802.1ad tagged frames and no STP is used, it will work.
Otherwise:
- If pvid is configured, it can put only 802.1Q tags but cannot put 802.1ad
tags.
- If 802.1Q and 802.1ad tagged frames arrive in mixture, it applies filtering
regardless of their protocols.
- While an 802.1ad bridge should use another mac address for STP BPDU and
should forward customer's BPDU frames, it can't.
Thus, we can't properly handle frames once 802.1ad is used.
Handling 802.1ad is useful if we want to allow stacked vlans to be used,
e.g., guest VMs wants to use vlan tags and the host also wants to segregate
guest's traffic from other guests' by vlan tags.
Here is the image describing how to configure a bridge to filter VMs traffic.
+-------+p/u +-----+ +---------+
+----+ | |------|vnet0|--|User A VM|
|eth0|--|802.1ad| +-----+ +---------+
+----+ |bridge |p/u +-----+ +---------+
| |------|vnet1|--|User B VM|
+-------+ +-----+ +---------+
p/u: pvid/untagged
This patch set enables us to set vlan protocols per bridge.
This tries to implement a bridge like S-VLAN component in IEEE 802.1Q-2011
spec.
Note that there is another possible implementation that sets vlan protocols
per port. Some HW switches seem to take that approach.
However, I think per-bridge approach is better, because;
- I think the typical usage of an 802.1ad bridge is segregating 802.1Q tagged
traffic (like what is described above), and this doesn't need the ability to
be set protocols per port. Also, If a bridge has many ports and it supports
per-port setting, we might have to make much more extra configurations to
change protocols of all ports.
- I assume that the main perpose to set protocol per port is to assign S-VID
according to C-VID, or to realize two logical bridges (one is an 802.1Q
filtering bridge and the other is an 802.1ad filtering bridge) in one bridge.
The former usually needs additional features such as vlan id mapping, and
is likely to make bridge's code complicated. If a user wants, such enhanced
features can be accomplished by a combination of multiple bridges, so it is
not absolutely necessary to implement these features in a bridge itself.
The latter is simply unnecessary because we can easily make two bridges of
which one is an 802.1Q bridge and the other is an 802.1ad bridge.
Here is an example of the enhanced feature that we can realize by using
multiple bridges and veth interfaces. This way is documented in
IEEE 802.1Q-2011 clause 15.4 (C-tagged service interface).
+----+ +-------+p/u +------+ +----+ +--+
|eth0|--|802.1ad|----veth----|802.1Q|--|vnet|--|VM|
+----+ |bridge |----veth----|bridge| +----+ +--+
+-------+p/u +------+
p/u: pvid/untagged
In this configuration, we can map C-VIDs to any S-VID.
For example;
C-VID 10 and 20 to S-VID 100
C-VID 30 to S-VID 110
This is achieved through the 802.1Q bridge that forwards C-tagged frames to
proper ports of the 802.1ad bridge.
Changes:
v1 -> v2:
- Make the way to forward bridge group addresses more generic by introducing
new mask, group_fwd_mask_required.
RFC -> v1:
- Add S-TAG tx offload.
- Remove a fix around stacked vlan which has already been fixed.
- Take into account Bridge Group Addresses.
- Separate handling of protocol-mismatch from br_vlan_get_tag().
- Change the way to set vlan_proto from netlink to sysfs because no other
existing configuration per bridge can be set by netlink.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables us to change the vlan protocol for vlan filtering.
We come to be able to filter frames on the basis of 802.1ad vlan tags
through a bridge.
This also changes br->group_addr if it has not been set by user.
This is needed for an 802.1ad bridge.
(See IEEE 802.1Q-2011 8.13.5.)
Furthermore, this sets br->group_fwd_mask_required so that an 802.1ad
bridge can forward the Nearest Customer Bridge group addresses except
for br->group_addr, which should be passed to higher layer.
To change the vlan protocol, write a protocol in sysfs:
# echo 0x88a8 > /sys/class/net/br0/bridge/vlan_protocol
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a bridge is an 802.1ad bridge, it must forward another bridge group
addresses (the Nearest Customer Bridge group addresses).
(For details, see IEEE 802.1Q-2011 8.6.3.)
As user might not want group_fwd_mask to be modified by enabling 802.1ad,
introduce a new mask, group_fwd_mask_required, which indicates addresses
the bridge wants to forward. This will be set by enabling 802.1ad.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables a bridge to have vlan protocol informantion and allows vlan
tag manipulation (retrieve, insert and remove tags) according to the vlan
protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bridge device doesn't need to embed S-tag into skb->data.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit e9ce7cb6b107 ("xen-netback: Factor queue-specific data into
queue struct") added a use of vzalloc/vfree to interface.c, but
removed the #include <linux/vmalloc.h> statement at the same time,
which causes this build error:
drivers/net/xen-netback/interface.c: In function 'xenvif_free':
drivers/net/xen-netback/interface.c:754:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(vif->queues);
^
cc1: some warnings being treated as errors
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Andrew J. Bennieston <andrew.bennieston@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using phy_drivers_register/_unregister functions is proper way to
handle multiple PHY drivers registration. For Realtek PHY drivers
module, it fixes incomplete current error-handlings up and adds
missed unregistration for the RTL8201CP driver.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an issue that we cannot use nfs rootfs correctly
on r8a7790 when the command below runs on a host PC.
$ sudo ping -f -l 8 $BOARD_IP_ADDR
Since the driver sets the RACT to 1 in the first while loop of
sh_eth_rx(), the controller accepts a next frame into the next RX
descriptor during the while loop. But, in the first while loop
doesn't allocate a next skb. So, this patch removes the RACT setting
in the first while loop of sh_eth_rx().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the packet "exceeded" condition in sh_eth_rx() when
RACT in an RX descriptor is not set and the "quota" is 0.
Otherwise, kernel panic happens because the "&n->poll_list" is deleted
twice in sh_eth_poll() which calls napi_complete() and net_rx_action().
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix compiler warning on 32-bit architectures:
net/core/filter.c: In function '__sk_run_filter':
net/core/filter.c:540:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
net/core/filter.c:550:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
net/core/filter.c:560:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 4f4482dcd9a0606a30541ff165ddaca64748299b ("tipc: compensate
for double accounting in socket rcv buffer") we access 'truesize' of
a received buffer after it might have been released by the function
filter_rcv().
In this commit we correct this by reading the value of 'truesize' to
the stack before delivering the buffer to filter_rcv().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SXGBE_CORE_L34_ADDCTL_REG define is cut and pasted twice so we can
delete the second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QLC_83XX_GET_LSO_CAPABILITY define is cut and pasted twice so we can
delete the second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Amir Vadai says:
====================
cpumask,net: affinity hint helper function
This patchset will set affinity hint to influence IRQs to be allocated on the
same NUMA node as the one where the card resides. As discussed in
http://www.spinics.net/lists/netdev/msg271497.html
If number of IRQs allocated is greater than the number of local NUMA cores, all
local cores will be used first, and the rest of the IRQs will be on a remote
NUMA node.
If no NUMA support - IRQ's and cores will be mapped 1:1
Since the utility function to calculate the mapping could be useful in other mq
drivers in the kernel, it was added to cpumask.[ch]
This patchset was tested and applied on top of net-next since the first
consumer is a network device (mlx4_en). Over commit fff1f59 "mac802154:
llsec: add forgotten list_del_rcu in key removal"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.
We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it. To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores. If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function sets the n'th cpu - local cpu's first.
For example: in a 16 cores server with even cpu's local, will get the
following values:
cpumask_set_cpu_local_first(0, numa, cpumask) => cpu 0 is set
cpumask_set_cpu_local_first(1, numa, cpumask) => cpu 2 is set
...
cpumask_set_cpu_local_first(7, numa, cpumask) => cpu 14 is set
cpumask_set_cpu_local_first(8, numa, cpumask) => cpu 1 is set
cpumask_set_cpu_local_first(9, numa, cpumask) => cpu 3 is set
...
cpumask_set_cpu_local_first(15, numa, cpumask) => cpu 15 is set
Curently this function will be used by multi queue networking devices to
calculate the irq affinity mask, such that as many local cpu's as
possible will be utilized to handle the mq device irq's.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management update from Zhang Rui:
"Specifics:
- fix a bug in Exynos thermal driver, which overwrites the hardware
trip point threshold when updating software trigger levels and
results in emergency shutdown. From: Tushar Behera.
- add thermal sensor support for Armada 375 and 38x SoCs. From
Ezequiel Garcia.
- add TMU (Thermal Management Unit) support for Exynos5260 and
Exynos5420 SoCs. From Naveen Krishna Chatradhi.
- add support for the additional digital temperature sensors in the
Intel SoCs like Bay Trail. From: Srinivas Pandruvada.
- a couple of cleanups and small fixes from Jingoo Han, Bartlomiej
Zolnierkiewicz, Geert Uytterhoeven, Jacob Pan, Paul Walmsley and
Lan,Tianyu"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (21 commits)
thermal: spear: remove unnecessary OOM messages
thermal: exynos: remove unnecessary OOM messages
thermal: rcar: remove unnecessary OOM messages
thermal: armada: Support Armada 380 SoC
thermal: armada: Support Armada 375 SoC
thermal: armada: Allow to specify an 'inverted readout' sensor
thermal: armada: Pass the platform_device to init_sensor()
thermal: armada: Add generic infrastructure to handle the sensor
thermal: armada: Add infrastructure to support generic formulas
thermal: armada: Rename armada_thermal_ops struct
thermal/intel_powerclamp: add newer cpu ids
thermal: rcar: Use pm_runtime_put() i.s.o. pm_runtime_put_sync()
thermal: samsung: Only update available threshold limits
Thermal/int3403: Fix thermal hysteresis unit conversion
thermal: Intel SoC DTS thermal
thermal: samsung: Add TMU support for Exynos5260 SoCs
thermal: samsung: Add TMU support for Exynos5420 SoCs
thermal: samsung: change base_common to more meaningful base_second
thermal: samsung: replace inten_ bit fields with intclr_
thermal: offer Samsung thermal support only when ARCH_EXYNOS is defined
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"The majority of these changes are cleanups and fixes across all
drivers. Redundant error messages are removed and more PWM
controllers set the .can_sleep flag to signal that they can't be used
in atomic context.
Support is added for the Broadcom Kona family of SoCs and the Intel
LPSS driver can now probe PCI devices in addition to ACPI devices.
Upon shutdown, the pwm-backlight driver will now power off the
backlight. It also uses the new descriptor-based GPIO API for more
concise GPIO handling.
A large chunk of these changes also converts platforms to use the
lookup mechanism rather than relying on the global number space to
reference PWM devices. This is largely in preparation for more
unification and cleanups in future patches. Eventually it will allow
the legacy PWM API to be removed"
* tag 'pwm/for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (38 commits)
pwm: fsl-ftm: set pwm_chip can_sleep flag
pwm: ab8500: Fix wrong value shift for disable/enable PWM
pwm: samsung: do not set manual update bit in pwm_samsung_config
pwm: lp3943: Set pwm_chip can_sleep flag
pwm: atmel: set pwm_chip can_sleep flag
pwm: mxs: set pwm_chip can_sleep flag
pwm: tiehrpwm: inline accessor functions
pwm: tiehrpwm: don't build PM related functions when not needed
pwm-backlight: retrieve configured PWM period
leds: leds-pwm: retrieve configured PWM period
ARM: pxa: hx4700: use PWM_LOOKUP to initialize struct pwm_lookup
ARM: shmobile: armadillo: use PWM_LOOKUP to initialize struct pwm_lookup
ARM: OMAP3: Beagle: use PWM_LOOKUP to initialize struct pwm_lookup
pwm: modify PWM_LOOKUP to initialize all struct pwm_lookup members
ARM: pxa: hx4700: initialize all the struct pwm_lookup members
ARM: OMAP3: Beagle: initialize all the struct pwm_lookup members
pwm: renesas-tpu: remove unused struct tpu_pwm_platform_data
ARM: shmobile: armadillo: initialize all struct pwm_lookup members
pwm: add period and polarity to struct pwm_lookup
pwm: twl: Really disable twl6030 PWMs
...
|
|
DM thinp already checks whether the discard_granularity of the data
device is a factor of the thin-pool block size. But when using the
dm-thin-pool's discard passdown support, DM thinp was not selecting the
max of the underlying data device's discard_granularity and the
thin-pool's block size.
Update set_discard_limits() to set discard_granularity to the max of
these values. This enables blkdev_issue_discard() to properly align the
discards that are sent to the DM thin device on a full block boundary.
As such each discard will now cover an entire DM thin-pool block and the
block will be reclaimed.
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
Split the single per bio-prison lock by using per bucket locking. Per
bucket locking benefits both dm-thin and dm-cache targets by reducing
bio-prison lock contention.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
* pci/msi:
PCI/MSI: Fix memory leak in free_msi_irqs()
* pci/iommu:
PCI: Add function 1 DMA alias quirk for HighPoint RocketRaid 642L
PCI: Add bridge DMA alias quirk for ITE bridge
* pci/cleanup:
PCI: Merge multi-line quoted strings
PCI: Whitespace cleanup
PCI: Move EXPORT_SYMBOL so it immediately follows function/variable
|
|
This patch updates vhost_scsi_get_tag() to accept the combined
expected data transfer length + T10 PI bytes as the value passed
into target_submit_cmd().
This is required now that target-core logic in commit 14ef9200
expects to subtract se_cmd->prot_length from se_cmd->data_length.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
In various areas of the code, it is assumed that
se_cmd->data_length describes pure data. In case
that protection information exists over the wire
(protect bits is are on) the target core re-calculates
the data length from the CDB and the backed device
block size (instead of each transport peeking in the cdb).
Modify loopback device to include protection information
in the transferred data length (like other scsi transports).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
In case protection information exists over the wire
iscsi header data length is required to include it.
Use protection information aware scsi helpers to set
the correct transfer length.
In order to avoid breakage, remove iser transfer length
checks for each task as they are not always true and
somewhat redundant anyway.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
In case protection information exists on the wire
scsi transports should include it in the transfer
byte count (even if protection information does not
exist in the host memory space). This helper will
compute the total transfer length from the scsi
command data length and protection attributes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This device uses function 1 as the PCIe requester ID.
This vendor has similar boards based on the same Marvell 88SE9235 chipset,
but this patch was only tested with the 642L.
Tested on ASUS Sabertooth 990FX (AMD).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=42679
Signed-off-by: Jérôme Carretero <cJ-ko@zougloub.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-06-11
This series contains updates to igb, i40e and i40evf.
Todd makes a change to igb to un-hide invariant returns by getting rid of
the E1000_SUCCESS define and converting those returns to return 0.
Jacob separates the hardware logic from the set function, so that we can
re-use it during a ptp_reset in igb. This enables the reset to return
functionality to the last know timestamp mode, rather than resetting the
value.
Ashish implements context flags for headwb and headwb_addr so that we
do not have to keep them always enabled.
Shannon updates the admin queue API for the new firmware, which adds
set_pf_content, nvm_config_read/write, replaces set_phy_reset with
set_phy_debug and removes nvm_read/write_reg_se. Cleans up the driver
to use the stored base_queue value since there is no need to read the
PCI register for the PF's base queue on every single transmit queue
enable and disable as we already have the value stored from reading
the capability features at startup.
Anjali changes the notion of source and destination for FD_SB in ethtool
to align i40e with other drivers. Adds flow director statistics to
the PF stats. Fixes a bug in ethtool for flow director drop packet
filter where the drop action comes down as a ring_cookie value, so allow
it as a special value that can be used to configure destination control.
Mitch fixes the i40evf to keep the driver from going down when it is
already in a down state. This prevents a CPU soft lock in napi_disable().
Also change the i40evf to check the admin queue error bits since the
firmware can indicate any admin queue error states to the driver via
some bits in the length registers.
Neerav separates out the DCB capability and enabled flags because currently
if the firmware reports DCB capability the driver enables
I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver inserts
a tag when transmitting a packet from the port even if there are no DCB
traffic classes configured at the port. So by adding the additional flag,
I40E_FLAG_DCB_CAPABLE, that will be set when the DCB capability is present
and the existing enabled flag will only be set if there are more than one
traffic classes configured at the port.
Greg fixes the i40e driver to not automatically accept tagged packets by
default so that the system must request a VLAN tag packet filter to get
packets with that tag. Greg also converts i40e to use the in-kernel
ether_addr_copy() instead of mempcy().
Jesse removes the FTYPE field from the receive descriptor to match the
hardware implementation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
SCTP update
This set contains transport path selection improvements in
SCTP. Please see individual patches for details.
====================
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the following sparse warning:
net/sctp/associola.c:1556:29: warning: incorrect type in initializer (different base types)
net/sctp/associola.c:1556:29: expected bool [unsigned] [usertype] preload
net/sctp/associola.c:1556:29: got restricted gfp_t
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function sctp_select_active_and_retran_path(), we walk the
transport list in order to look for the two most recently used
ACTIVE transports (trans_pri, trans_sec). In case we didn't find
anything ACTIVE, we currently just camp on a possibly PF or
INACTIVE transport that is primary path; this behavior actually
dates back to linux-history tree of the very early days of
lksctp, and can yield a behavior that chooses suboptimal
transport paths.
Instead, be a bit more clever by reusing and extending the
recently introduced sctp_trans_elect_best() handler. In case
both transports are evaluated to have the same score resulting
from their states, break the tie by looking at: 1) transport
patch error count 2) last_time_heard value from each transport.
This is analogous to Nishida's Quick Failover draft [1],
section 5.1, 3:
The sender SHOULD avoid data transmission to PF destinations.
When all destinations are in either PF or Inactive state,
the sender MAY either move the destination from PF to active
state (and transmit data to the active destination) or the
sender MAY transmit data to a PF destination. In the former
scenario, (i) the sender MUST NOT notify the ULP about the
state transition, and (ii) MUST NOT clear the destination's
error counter. It is recommended that the sender picks the
PF destination with least error count (fewest consecutive
timeouts) for data transmission. In case of a tie (multiple PF
destinations with same error count), the sender MAY choose the
last active destination.
Thus for sctp_select_active_and_retran_path(), we keep track of
the best, if any, transport that is in PF state and in case no
ACTIVE transport has been found (hence trans_{pri,sec} is NULL),
we select the best out of the three: current primary_path and
retran_path as well as a possible PF transport.
The secondary may still camp on the original primary_path as
before. The change in sctp_trans_elect_best() with a more fine
grained tie selection also improves at the same time path selection
for sctp_assoc_update_retran_path() in case of non-ACTIVE states.
[1] http://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Be more precise in transport path selection and use ktime
helpers instead of jiffies to compare and pick the better
primary and secondary recently used transports. This also
avoids any side-effects during a possible roll-over, and
could lead to better path decision-making.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch just refactors and moves the code for the active
path selection into its own helper function outside of
sctp_assoc_control_transport() which is already big enough.
No functional changes here.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two minimal helper functions analogous to time_before() and
time_after() that will later on both be needed by SCTP code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an initiator sends an allocation length bigger than what its
command consumes, the target should only return the actual response data
and set the residual length to the unused part of the allocation length.
Add a helper function that command handlers (INQUIRY, READ CAPACITY,
etc) can use to do this correctly, and use this code to get the correct
residual for commands that don't use the full initiator allocation in the
handlers for READ CAPACITY, READ CAPACITY(16), INQUIRY, MODE SENSE and
REPORT LUNS.
This addresses a handful of failures as reported by Christophe with
the Windows Certification Kit:
http://permalink.gmane.org/gmane.linux.scsi.target.devel/6515
Signed-off-by: Roland Dreier <roland@purestorage.com>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Phoebe Buckheister says:
====================
Recent llsec code introduced a memory leak on decryption failures during rx.
This fixes said leak, and optimizes the receive loops for monitor and wpan
devices to only deliver skbs to devices that are actually up. Also changes a
dev_kfree_skb to kfree_skb when an invalid packet is dropped before being
pushed into the stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only one WPAN devices can be active at any given time, so only deliver
packets to that one interface that is actually up. Multiple monitors may
be up at any given time, but we don't have to deliver to monitors that
are down either.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mac802154 RX did not free skbs on decryption failure, assuming that the
caller would when the local rx handler returned _DROP. This was false.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After relatively recent changes in the ACPI-based PCI hotplug
(ACPIPHP) code, the acpiphp_check_host_bridge() executed for PCI
host bridges via acpi_pci_root_scan_dependent() doesn't do anything
useful, because those bridges do not have hotplug contexts. That
happens by mistake, so fix it by making acpiphp_enumerate_slots()
add hotplug contexts to PCI host bridges too and modify
acpiphp_remove_slots() to drop those contexts for host bridges
as appropriate.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=76901
Fixes: 2d8b1d566a5f (ACPI / hotplug / PCI: Get rid of check_sub_bridges())
Reported-and-tested-by: Gavin Guo <gavin.guo@canonical.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch extracts LBA + sectors for VERIFY, and adds a goto check_lba
to perform the end-of-device checking.
(Update patch to drop lba_check usage - nab)
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
