4. Remote Controller devices

4.1. Remote Controller core

The remote controller core implements infrastructure to receive and send remote controller keyboard keystrokes and mouse events.

Every time a key is pressed on a remote controller, a scan code is produced. Also, on most hardware, keeping a key pressed for more than a few dozens of milliseconds produce a repeat key event. That’s somewhat similar to what a normal keyboard or mouse is handled internally on Linux[1]. So, the remote controller core is implemented on the top of the linux input/evdev interface.

However, most of the remote controllers use infrared (IR) to transmit signals. As there are several protocols used to modulate infrared signals, one important part of the core is dedicated to adjust the driver and the core system to support the infrared protocol used by the emitter.

The infrared transmission is done by blinking a infrared emitter using a carrier. The carrier can be switched on or off by the IR transmitter hardware. When the carrier is switched on, it is called PULSE. When the carrier is switched off, it is called SPACE.

In other words, a typical IR transmission can be viewed as a sequence of PULSE and SPACE events, each with a given duration.

The carrier parameters (frequency, duty cycle) and the intervals for PULSE and SPACE events depend on the protocol. For example, the NEC protocol uses a carrier of 38kHz, and transmissions start with a 9ms PULSE and a 4.5ms SPACE. It then transmits 16 bits of scan code, being 8 bits for address (usually it is a fixed number for a given remote controller), followed by 8 bits of code. A bit “1” is modulated with 560µs PULSE followed by 1690µs SPACE and a bit “0” is modulated with 560µs PULSE followed by 560µs SPACE.

At receiver, a simple low-pass filter can be used to convert the received signal in a sequence of PULSE/SPACE events, filtering out the carrier frequency. Due to that, the receiver doesn’t care about the carrier’s actual frequency parameters: all it has to do is to measure the amount of time it receives PULSE/SPACE events. So, a simple IR receiver hardware will just provide a sequence of timings for those events to the Kernel. The drivers for hardware with such kind of receivers are identified by RC_DRIVER_IR_RAW, as defined by rc_driver_type[2]. Other hardware come with a microcontroller that decode the PULSE/SPACE sequence and return scan codes to the Kernel. Such kind of receivers are identified by RC_DRIVER_SCANCODE.

When the RC core receives events produced by RC_DRIVER_IR_RAW IR receivers, it needs to decode the IR protocol, in order to obtain the corresponding scan code. The protocols supported by the RC core are defined at enum rc_proto.

When the RC code receives a scan code (either directly, by a driver of the type RC_DRIVER_SCANCODE, or via its IR decoders), it needs to convert into a Linux input event code. This is done via a mapping table.

The Kernel has support for mapping tables available on most media devices. It also supports loading a table in runtime, via some sysfs nodes. See the RC userspace API for more details.

4.1.1. Remote controller data structures and functions

enum rc_driver_type

type of the RC driver.

Constants

RC_DRIVER_SCANCODE

Driver or hardware generates a scancode.

RC_DRIVER_IR_RAW

Driver or hardware generates pulse/space sequences. It needs a Infra-Red pulse/space decoder

RC_DRIVER_IR_RAW_TX

Device transmitter only, driver requires pulse/space data sequence.

struct rc_scancode_filter

Filter scan codes.

Definition:

struct rc_scancode_filter {
    u32 data;
    u32 mask;
};

Members

data

Scancode data to match.

mask

Mask of bits of scancode to compare.

enum rc_filter_type

Filter type constants.

Constants

RC_FILTER_NORMAL

Filter for normal operation.

RC_FILTER_WAKEUP

Filter for waking from suspend.

RC_FILTER_MAX

Number of filter types.

struct lirc_fh

represents an open lirc file

Definition:

struct lirc_fh {
    struct list_head list;
    struct rc_dev *rc;
    int carrier_low;
    unsigned int *rawir;
    struct lirc_scancode *scancodes;
    wait_queue_head_t wait_poll;
    u8 send_mode;
    u8 rec_mode;
};

Members

list

list of open file handles

rc

rcdev for this lirc chardev

carrier_low

when setting the carrier range, first the low end must be set with an ioctl and then the high end with another ioctl

rawir

queue for incoming raw IR

scancodes

queue for incoming decoded scancodes

wait_poll

poll struct for lirc device

send_mode

lirc mode for sending, either LIRC_MODE_SCANCODE or LIRC_MODE_PULSE

rec_mode

lirc mode for receiving, either LIRC_MODE_SCANCODE or LIRC_MODE_MODE2

struct rc_dev

represents a remote control device

Definition:

struct rc_dev {
    struct device                   dev;
    bool managed_alloc;
    const struct attribute_group    *sysfs_groups[5];
    const char                      *device_name;
    const char                      *input_phys;
    struct input_id                 input_id;
    const char                      *driver_name;
    const char                      *map_name;
    struct rc_map                   rc_map;
    struct mutex                    lock;
    unsigned int                    minor;
    struct ir_raw_event_ctrl        *raw;
    struct input_dev                *input_dev;
    enum rc_driver_type             driver_type;
    bool idle;
    bool encode_wakeup;
    u64 allowed_protocols;
    u64 enabled_protocols;
    u64 allowed_wakeup_protocols;
    enum rc_proto                   wakeup_protocol;
    struct rc_scancode_filter       scancode_filter;
    struct rc_scancode_filter       scancode_wakeup_filter;
    u32 scancode_mask;
    u32 users;
    void *priv;
    spinlock_t keylock;
    bool keypressed;
    unsigned long                   keyup_jiffies;
    struct timer_list               timer_keyup;
    struct timer_list               timer_repeat;
    u32 last_keycode;
    enum rc_proto                   last_protocol;
    u64 last_scancode;
    u8 last_toggle;
    u32 timeout;
    u32 min_timeout;
    u32 max_timeout;
    u32 rx_resolution;
#ifdef CONFIG_LIRC;
    struct device                   lirc_dev;
    struct cdev                     lirc_cdev;
    ktime_t gap_start;
    spinlock_t lirc_fh_lock;
    struct list_head                lirc_fh;
#endif;
    bool registered;
    int (*change_protocol)(struct rc_dev *dev, u64 *rc_proto);
    int (*open)(struct rc_dev *dev);
    void (*close)(struct rc_dev *dev);
    int (*s_tx_mask)(struct rc_dev *dev, u32 mask);
    int (*s_tx_carrier)(struct rc_dev *dev, u32 carrier);
    int (*s_tx_duty_cycle)(struct rc_dev *dev, u32 duty_cycle);
    int (*s_rx_carrier_range)(struct rc_dev *dev, u32 min, u32 max);
    int (*tx_ir)(struct rc_dev *dev, unsigned *txbuf, unsigned n);
    void (*s_idle)(struct rc_dev *dev, bool enable);
    int (*s_wideband_receiver)(struct rc_dev *dev, int enable);
    int (*s_carrier_report) (struct rc_dev *dev, int enable);
    int (*s_filter)(struct rc_dev *dev, struct rc_scancode_filter *filter);
    int (*s_wakeup_filter)(struct rc_dev *dev, struct rc_scancode_filter *filter);
    int (*s_timeout)(struct rc_dev *dev, unsigned int timeout);
};

Members

dev

driver model’s view of this device

managed_alloc

devm_rc_allocate_device was used to create rc_dev

sysfs_groups

sysfs attribute groups

device_name

name of the rc child device

input_phys

physical path to the input child device

input_id

id of the input child device (struct input_id)

driver_name

name of the hardware driver which registered this device

map_name

name of the default keymap

rc_map

current scan/key table

lock

used to ensure we’ve filled in all protocol details before anyone can call show_protocols or store_protocols

minor

unique minor remote control device number

raw

additional data for raw pulse/space devices

input_dev

the input child device used to communicate events to userspace

driver_type

specifies if protocol decoding is done in hardware or software

idle

used to keep track of RX state

encode_wakeup

wakeup filtering uses IR encode API, therefore the allowed wakeup protocols is the set of all raw encoders

allowed_protocols

bitmask with the supported RC_PROTO_BIT_* protocols

enabled_protocols

bitmask with the enabled RC_PROTO_BIT_* protocols

allowed_wakeup_protocols

bitmask with the supported RC_PROTO_BIT_* wakeup protocols

wakeup_protocol

the enabled RC_PROTO_* wakeup protocol or RC_PROTO_UNKNOWN if disabled.

scancode_filter

scancode filter

scancode_wakeup_filter

scancode wakeup filters

scancode_mask

some hardware decoders are not capable of providing the full scancode to the application. As this is a hardware limit, we can’t do anything with it. Yet, as the same keycode table can be used with other devices, a mask is provided to allow its usage. Drivers should generally leave this field in blank

users

number of current users of the device

priv

driver-specific data

keylock

protects the remaining members of the struct

keypressed

whether a key is currently pressed

keyup_jiffies

time (in jiffies) when the current keypress should be released

timer_keyup

timer for releasing a keypress

timer_repeat

timer for autorepeat events. This is needed for CEC, which has non-standard repeats.

last_keycode

keycode of last keypress

last_protocol

protocol of last keypress

last_scancode

scancode of last keypress

last_toggle

toggle value of last command

timeout

optional time after which device stops sending data

min_timeout

minimum timeout supported by device

max_timeout

maximum timeout supported by device

rx_resolution

resolution (in us) of input sampler

lirc_dev

lirc device

lirc_cdev

lirc char cdev

gap_start

start time for gap after timeout if non-zero

lirc_fh_lock

protects lirc_fh list

lirc_fh

list of open files

registered

set to true by rc_register_device(), false by rc_unregister_device

change_protocol

allow changing the protocol used on hardware decoders

open

callback to allow drivers to enable polling/irq when IR input device is opened.

close

callback to allow drivers to disable polling/irq when IR input device is opened.

s_tx_mask

set transmitter mask (for devices with multiple tx outputs)

s_tx_carrier

set transmit carrier frequency

s_tx_duty_cycle

set transmit duty cycle (0% - 100%)

s_rx_carrier_range

inform driver about carrier it is expected to handle

tx_ir

transmit IR

s_idle

enable/disable hardware idle mode, upon which, device doesn’t interrupt host until it sees IR pulses

s_wideband_receiver

enable wide band receiver used for learning

s_carrier_report

enable carrier reports

s_filter

set the scancode filter

s_wakeup_filter

set the wakeup scancode filter. If the mask is zero then wakeup should be disabled. wakeup_protocol will be set to a valid protocol if mask is nonzero.

s_timeout

set hardware timeout in us

struct rc_dev *rc_allocate_device(enum rc_driver_type)

Allocates a RC device

Parameters

enum rc_driver_type

specifies the type of the RC output to be allocated returns a pointer to struct rc_dev.

struct rc_dev *devm_rc_allocate_device(struct device *dev, enum rc_driver_type)

Managed RC device allocation

Parameters

struct device *dev

pointer to struct device

enum rc_driver_type

specifies the type of the RC output to be allocated returns a pointer to struct rc_dev.

void rc_free_device(struct rc_dev *dev)

Frees a RC device

Parameters

struct rc_dev *dev

pointer to struct rc_dev.

int rc_register_device(struct rc_dev *dev)

Registers a RC device

Parameters

struct rc_dev *dev

pointer to struct rc_dev.

int devm_rc_register_device(struct device *parent, struct rc_dev *dev)

Manageded registering of a RC device

Parameters

struct device *parent

pointer to struct device.

struct rc_dev *dev

pointer to struct rc_dev.

void rc_unregister_device(struct rc_dev *dev)

Unregisters a RC device

Parameters

struct rc_dev *dev

pointer to struct rc_dev.

struct rc_map_table

represents a scancode/keycode pair

Definition:

struct rc_map_table {
    u64 scancode;
    u32 keycode;
};

Members

scancode

scan code (u64)

keycode

Linux input keycode

struct rc_map

represents a keycode map table

Definition:

struct rc_map {
    struct rc_map_table     *scan;
    unsigned int            size;
    unsigned int            len;
    unsigned int            alloc;
    enum rc_proto           rc_proto;
    const char              *name;
    spinlock_t lock;
};

Members

scan

pointer to struct rc_map_table

size

Max number of entries

len

Number of entries that are in use

alloc

size of *scan, in bytes

rc_proto

type of the remote controller protocol, as defined at enum rc_proto

name

name of the key map table

lock

lock to protect access to this structure

struct rc_map_list

list of the registered rc_map maps

Definition:

struct rc_map_list {
    struct list_head         list;
    struct rc_map map;
};

Members

list

pointer to struct list_head

map

pointer to struct rc_map

int rc_map_register(struct rc_map_list *map)

Registers a Remote Controller scancode map

Parameters

struct rc_map_list *map

pointer to struct rc_map_list

void rc_map_unregister(struct rc_map_list *map)

Unregisters a Remote Controller scancode map

Parameters

struct rc_map_list *map

pointer to struct rc_map_list

struct rc_map *rc_map_get(const char *name)

gets an RC map from its name

Parameters

const char *name

name of the RC scancode map