| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Various filesystem drivers have grown a get_dentry() function that's a
duplicate of lookup_one_len, except that it doesn't take a maximum length
argument and doesn't check for \0 or / in the passed in filename.
Switch all these places to use lookup_one_len.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Greg KH <greg@kroah.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Patch to add check to get_chrdev_list and get_blkdev_list to prevent reads
of /proc/devices from spilling over the provided page if more than 4096
bytes of string data are generated from all the registered character and
block devices in a system
Signed-off-by: Neil Horman <nhorman@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Looks like locking can be optimised quite a lot. Increase lock widths
slightly so lo_lock is taken fewer times per request. Also it was quite
trivial to cover lo_pending with that lock, and remove the atomic
requirement. This also makes memory ordering explicitly correct, which is
nice (not that I particularly saw any mem ordering bugs).
Test was reading 4 250MB files in parallel on ext2-on-tmpfs filesystem (1K
block size, 4K page size). System is 2 socket Xeon with HT (4 thread).
intel:/home/npiggin# umount /dev/loop0 ; mount /dev/loop0 /mnt/loop ; /usr/bin/time ./mtloop.sh
Before:
0.24user 5.51system 0:02.84elapsed 202%CPU (0avgtext+0avgdata 0maxresident)k
0.19user 5.52system 0:02.88elapsed 198%CPU (0avgtext+0avgdata 0maxresident)k
0.19user 5.57system 0:02.89elapsed 198%CPU (0avgtext+0avgdata 0maxresident)k
0.22user 5.51system 0:02.90elapsed 197%CPU (0avgtext+0avgdata 0maxresident)k
0.19user 5.44system 0:02.91elapsed 193%CPU (0avgtext+0avgdata 0maxresident)k
After:
0.07user 2.34system 0:01.68elapsed 143%CPU (0avgtext+0avgdata 0maxresident)k
0.06user 2.37system 0:01.68elapsed 144%CPU (0avgtext+0avgdata 0maxresident)k
0.06user 2.39system 0:01.68elapsed 145%CPU (0avgtext+0avgdata 0maxresident)k
0.06user 2.36system 0:01.68elapsed 144%CPU (0avgtext+0avgdata 0maxresident)k
0.06user 2.42system 0:01.68elapsed 147%CPU (0avgtext+0avgdata 0maxresident)k
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch creates a new kstrdup library function and changes the "local"
implementations in several places to use this function.
Most of the changes come from the sound and net subsystems. The sound part
had already been acknowledged by Takashi Iwai and the net part by David S.
Miller.
I left UML alone for now because I would need more time to read the code
carefully before making changes there.
Signed-off-by: Paulo Marques <pmarques@grupopie.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
get_request_wait needn't unplug the device immediately.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Sprinkle around a few branch hints in the block layer.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This memory barrier is not needed because the waitqueue will only get waiters
on it in the following situations:
rq->count has exceeded the threshold - however all manipulations of ->count
are performed under the runqueue lock, and so we will correctly pick up any
waiter.
Memory allocation for the request fails. In this case, there is no additional
help provided by the memory barrier. We are guaranteed to eventually wake up
waiters because the request allocation mempool guarantees that if the mem
allocation for a request fails, there must be some requests in flight. They
will wake up waiters when they are retired.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add KERN_ERR and __FUNCTION__ to generic tag error messages, and add a comment
in blk_queue_end_tag() which explains the silent failure path.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Replace BLK_TAGS_PER_LONG with BITS_PER_LONG and remove unused BLK_TAGS_MASK.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
blk_queue_tag->real_max_depth was used to optimize out unnecessary
allocations/frees on tag resize. However, the whole thing was very broken -
tag_map was never allocated to real_max_depth resulting in access beyond the
end of the map, bits in [max_depth..real_max_depth] were set when initializing
a map and copied when resizing resulting in pre-occupied tags.
As the gain of the optimization is very small, well, almost nill, remove the
whole thing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
blk_queue_start_tag() hand-coded searching for the first zero bit in the tag
map. Replace it with find_first_zero_bit(). With this patch,
blk_queue_star_tag() doesn't need to fill remains of tag map with 1, thus
allowing it to work properly with the next remove_real_max_depth patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Patch to allocate the control structures for for ide devices on the node of
the device itself (for NUMA systems). The patch depends on the Slab API
change patch by Manfred and me (in mm) and the pcidev_to_node patch that I
posted today.
Does some realignment too.
Signed-off-by: Justin M. Forbes <jmforbes@linuxtx.org>
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Pravin Shelar <pravin@calsoftinc.com>
Signed-off-by: Shobhit Dayal <shobhit@calsoftinc.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
This patch fixes an obvious and nasty bug where we could exit the transmit
routine while holding tx_lock.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
|
|
|
|
bus_add_device()
Don't error out if something "bad" happens when trying to bind a driver to a
device. We want the sysfs attributes to be present for later when we try to
tear down the device.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Drivers need to return -ENODEV when they can't bind to a device.
Anything else stops the "bind a device to a driver" search.
From: Stelian Pop <stelian@popies.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use ssleep() / msleep() [as appropriate]
instead of schedule_timeout() to guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Not all architectures implement asm/rtc.h
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch removes the support for the W83697HF and W83627THF chips from
the w83781d driver. These chips have no I2C/SMBus interface and are
better supported by the Super-I/O-based w83627hf driver. Documentation
was updated to reflect the support drop.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add support for Maxim/Dallas DS1374 Real-Time Clock Chip
This change adds support for the Maxim/Dallas DS1374 RTC chip. This chip
is an I2C-based RTC that maintains a simple 32-bit binary seconds count
with battery backup support.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is an i2c driver for the Philips PCA9539 (16 bit I/O port).
It uses the new i2c-sysfs interfaces.
The patch includes documentation.
It depends on the patch that renames "i2c-sysfs.h" to "hwmon-sysfs.h"
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch renames the new linux/i2c-sysfs.h header file to
linux/hwmon-sysfs.h. This names seems to be more appropriate since this
file defines macros and structures not related to i2c but to hardware
monitoring drivers. The patch also updates the five hardware monitoring
driver which include that header file already.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds support for the MAX6875/MAX6874 chips.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch modifies the it87 hardware monitoring driver to take benefit
of the new sysfs callback features introduced by Yani Ioannou, making
the code much clearer and the resulting driver significantly smaller.
From: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I updated the lm63 hardware monitoring driver to take benefit of Yani
Ioannou's new sysfs callback capabilities.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I updated the lm83 hardware monitoring driver to take benefit of Yani
Ioannou's new sysfs callback capabilities.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I updated the lm90 hardware monitoring driver to take benefit of Yani
Ioannou's new sysfs callback capabilities.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I found a possible cleanup in the pcf8574 driver. We don't need to store
the read value in our private data structure, as we then never use it
again. I asked Aurelien and he is fine with the change. Please apply,
thanks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Following patch removes EXPERIMENTAL flag from some of I2C bus and chip
drivers. It is removed when the driver is in kernel at least from
2.6.3 and I generally think there is no problem with it.
Also this patch adds SiS 745 to help option of sis96x and it
also fixes nForce2 driver entry to reflect current state.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This adds an I2C driver for the TPS6501x series of power management chips.
It's used on many OMAP based boards, and this driver has been widely used
in the Linux-OMAP trees over the last year or so.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
i2c: Race fix for i2c-mpc.c
The problem was that the clock speed and driver data is
initialized after the i2c adapter was added. This caused
the i2c bus to start working at a wrong speed. (Mostly
noticable on the second bus on mpc5200)
With this patch we've tried to keep the i2c adapter
working perfectly all the time it is included in the system.
Initialize before added, Remove garbage after deleleted.
Submitted-by: Asier Llano Palacios
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes a misspelling in a comment section.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes a misspelling in a comment section.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes a double "the" in a comment section.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes the some misspellings and a trailing whitespace in
the comments.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch kills another macro abuse in the via686a hardware monitoring
driver. Using a macro just to alias an array is quite useless, isn't it?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Here are some corrections for drivers/i2c/chips/Kconfig.
Signed-off-by: Alexey Fisher <fishor@gmx.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch removes die_code from adm1021 as nothing within the
driver uses it.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The via686a hardware monitoring driver has infamous coding style at the
moment. I'd like to clean up the mess before I start working on other
changes to this driver. Is the following patch acceptable? No code
change, only coding style (indentation, alignments, trailing white
space, a few parentheses and a typo).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch kills a common macro abuse in i2c chip drivers: defining
ALARMS_FROM_REG returning its argument unchanged. Dropping the macro
makes the code somewhat more readable IMHO.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch includes jiffies.h in two i2c drivers.
(jiffies.h is needed for the time_after function.)
Signed-off-by: Dominik Hackl <dominik@hackl.dhs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds an info print of detected VRM stolen from Sebastian
Witt's atxp1 sriver. ADM9240 already has vrm accessor removed.
Write no-op and whitespace fixes removed :)
Couple of comments changed, tested on 2.6.11.9.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This small patch changes two drivers, adm1025 and adm1026, to
report vid as cpu0_vid sysfs name as used by the other drivers.
Added duplicated names and six month warning for old names to
be removed as requested. Compile tested.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Jarkko Lavinen provided patch to fix: "couldn't set the divisor 128
through fan1_div sysfs entry even though the chip supports it and
setting divisors 1..64 worked. This was due to POWER_TO_REG() only
checking 2's powers 0 till 5 but not 6."
This patch applies that fix to w83627hf and w83781d drivers.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
In my cross-reference checking of sysfs names, the via686a needs
special case treatment as it the only driver expands S_IWUSR to
00200 with gcc -E. (00200 is the correct value for S_IWUSR).
This is caused by the driver including <linux/delay.h>, it compiles
fine without that header but I am unable to test drive the change.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Call i2c_transfer() from i2c_master_send() and i2c_master_recv() to
avoid the redundant code that was in all three functions. It also
removes unnecessary debug statements as suggested by Jean Delvare.
This is important for the non-blocking interfaces because they will
have to handle a non-blocking interface in this area. Having it in
one place greatly simplifies the changes.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I2C-MPC: Allow for sharing of the interrupt line
On the MPC8548 devices we have multiple I2C-MPC buses however they are on the
same interrupt line. Made request_irq pass SA_SHIRQ now so the second bus can
register for the same IRQ.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Here are some spelling corrections for drivers/i2c.
occured -> occurred
intialization -> initialization
Everytime -> Every time
transfering -> transferring
relevent -> relevant
continous -> continuous
neccessary -> necessary
explicitely -> explicitly
Celcius -> Celsius
differenciate -> differentiate
Signed-off-by: Steven Cole <elenstev@mesatop.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This simple patch adds support for the SMSC LPC47M15x and LPC47M192
chips to the smsc47m1 hardware monitoring driver. These chips are
compatible with the other ones already supported by the driver, so I see
no reason not to support them, especially when the Linux 2.4 version of
the driver does already.
I also modified the info printks to name the chips by their real name.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
These are the fixes for the bug you spotted in my new w83627ehf driver:
- Explicit division by 0.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is a new hardware monitoring driver, w83627ehf, which supports the
Winbond W83627EHF Super-I/O chip. The driver is not complete, but
already usable. It only implements fan speed and temperature monitoring,
while the chip also supports voltage inputs with VID, PWM output and
temperature sensor selection. I have no more time to work on this, but
anyone with supported hardware could add the missing functionalities
later.
This driver is largely derived from the w83627hf driver.
Thanks to Leon Moonen and Steve Cliffe for tesing the preliminary
versions of my driver and reporting the problems they encountered.
Thanks to Grant Coady for noticing and fixing various corner cases in
the fan management. This third version of the driver hopefully addresses
all the issues the original version had.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Completion of Michiel Rook's port of adm9240 to 2.6 with addition
of auto fan clock divider based on Jean Delvare's algorithm, and
replaces scaling macros with static inlines.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Hi Alexey,
> Files that don't use CONFIG_* stuff shouldn't include config.h
> Files that use CONFIG_* stuff should include config.h
>
> It's that simple. ;-)
I agree. This won't change anything though, as all drivers include
either device.h or module.h, which in turn include config.h. But you are
still correct, so I approve your patch.
For completeness, I would propose the following on top of your own
patch:
i2c bus drivers do not need to define DEBUG themselves, as the Kconfig
system takes care of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Files that don't use CONFIG_* stuff shouldn't include config.h
Files that use CONFIG_* stuff should include config.h
It's that simple. ;-)
Signed-off-by: Alexey Dobriyan <adobriyan@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On Wed, May 04, 2005 at 12:07:11PM +0200, Jean Delvare wrote:
> Additionally, I would welcome an additional patch documenting the fact
> that the ds1337 driver will work fine with the Dallas DS1339 real-time
> clock chip.
Document the fact that ds1337 driver works also with DS1339 real-time
clock chip.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Chip is searched by bus number rather than its own proprietary id.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
i2c_transfer returns number of sucessfully transfered messages. Change
error checking to accordingly. (ds1337_set_datetime never returned
sucess)
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Make time format consistent with other RTC drivers.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
dev_{dbg,err} functions should print client's device name. data->id can
be dropped from message, because device is determined by bus it hangs on
(it has fixed address).
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use correct macros to convert between bdc and bin. See linux/bcd.h
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use i2c_transfer to send message, so we get proper bus locking.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Adds support for the Attansic ATXP1 I2C device, found on some x86
plattforms to change CPU and other voltages. Depends on the previous
i2c-vid.h patch.
Signed-off-by: Sebastian Witt <se.witt@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[PATCH] I2C rtc8564.c remove duplicate include
Trivial fix: removes duplicate include line.
Signed-off-by: Clemens Koller <clemens.koller@anagramm.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On top of my previous patch which removes the use of address ranges in
video i2c drivers, this one can save an additional few bytes of memory.
Most of these drivers which do not use I2C_CLIENT_INSMOD initialize the
unused address lists in a less than optimal way. This patch simply
optimizes this, by using a single one-element list instead of 3
different lists with two elements each.
This saves an average 63 bytes on these drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -ruN linux-2.6.12-rc1-bk5.orig/drivers/media/video/adv7170.c linux-2.6.12-rc1-bk5/drivers/media/video/adv7170.c
|
|
Some months ago, you killed the address ranges mechanism from all
sensors i2c chip drivers (both the module parameters and the in-code
address lists). I think it was a very good move, as the ranges can
easily be replaced by individual addresses, and this allowed for
significant cleanups in the i2c core (let alone the impressive size
shrink for all these drivers).
Unfortunately you did not do the same for non-sensors i2c chip drivers.
These need the address ranges even less, so we could get rid of the
ranges here as well for another significant i2c core cleanup. Here comes
a patch which does just that. Since the process is exactly the same as
what you did for the other drivers set already, I did not split this one
in parts.
A documentation update is included.
The change saves 308 bytes in the i2c core, and an average 1382 bytes
for chip drivers which use I2C_CLIENT_INSMOD, 126 bytes for those which
do not.
This change is required if we want to merge the sensors and non-sensors
i2c code (and we want to do this).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/Documentation/i2c/writing-clients
===================================================================
|
|
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
|
|
I've created reconnect feature - if on start there are no registered families
all new devices will have defailt family, later when driver for appropriate
family is loaded, slaves, which were faound earlier, will still have defult
family instead of right one. Reconnect feature will force control thread to run
through all master devices and all slaves found and search for slaves with
default family id and try to reconnect them.
It does not store newly registered family and does not check only those slaves
which have reg_num.family the same as being registered one - all slaves with
default family are reconnected.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
sysfs.
Adds a default family so that new slave families will show up in sysfs.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
disable/enable periodic searches.
Adds a sysfs entry (w1_master_search) that allows you to disable/enable
periodic searches.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
use it.
Adds the triplet w1 master method and changes w1_search() to use it.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Cleans up usage of touch_bit/w1_read_bit/w1_write_bit.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
We can access family id through w1_family structure.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Removed some fields which are not required.
First step for writing operations.
Now only read and read name remain.
Patch depends on w1 cleanups patch.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- white space changes.
- list_for_each_entry/list_for_each_entry_safe and reverse changes.
- small coding style changes.
- removed redundant NULL checks.
- use attribute group and macros instead of direct device attributes.
Patch is havily based on work from Adrian Bunk and Dmitry Torokhov,
thanks guys.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Support for new simple rom family [0x81 id].
It is the same as existing 0x01 family,
which is used in ds9490* w1 adapters.
Patch is on top of new-thermal-sensor-families patch.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Support for ds18b20, ds1822 thermal sensors.
Based on code from Tiziano M_ller <tm@dev-zero.ch>.
Patch is against 2.6.12-rc2 and should be applied
without problems on top of any later kernels since
w1_therm driver was not changed.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch removes some unneeded checks of pointers being NULL before
calling kfree() on them. kfree() handles NULL pointers just fine, checking
first is pointless.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
writeback
Due to the use of write-behind, it is possible for md to write a page to
the bitmap file that is still completing writeback. This is not allowed.
With this patch, we detect those cases and either force a sync write, or
back off and try later, as appropriate.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
1/ Must typecast int to (sector_t) before inverting or we
might not invert enough bits.
2/ When "bitmap_offset" was added to mdp_superblock_1, we didn't increase
the count of words-used (96 to 100).
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
currently, md updates all superblocks (one on each device) in series. It
waits for one write to complete before starting the next. This isn't a big
problem as superblock updates don't happen that often.
However it is neater to do it in parallel, and if the drives in the array have
gone to "sleep" after a period of idleness, then waking them is parallel is
faster (and someone else should be worrying about power drain).
Futher, we will need parallel superblock updates for a future patch which
keeps the intent-logging bitmap near the superblock.
Also remove the silly code that retired superblock updates 100 times. This
simply never made sense.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This provides an alternate to storing the bitmap in a separate file. The
bitmap can be stored at a given offset from the superblock. Obviously the
creator of the array must make sure this doesn't intersect with data....
After is good for version-0.90 superblocks.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Before completing a 'write' the md superblock might need to be updated.
This is best done by the md_thread.
The current code schedules this up and queues the write request for later
handling by the md_thread.
However some personalities (Raid5/raid6) will deadlock if the md_thread
tries to submit requests to its own array.
So this patch changes things so the processes submitting the request waits
for the superblock to be written and then submits the request itself.
This fixes a recently-created deadlock in raid5/raid6
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When an array is degraded, bit in the intent-bitmap are never cleared. So if
a recently failed drive is re-added, we only need to reconstruct the block
that are still reflected in the bitmap.
This patch adds support for this re-adding.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Otherwise it could have a random value and might BUG. This fixes a BUG
during resync problem in raid1 introduced by the bitmap-based-intent-loggin
patches.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The logic here is wrong. if fullsync is 0, it WILL BUG.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When looking for pages that need cleaning we skip pages that don't have
BITMAP_PAGE_CLEAN set. But if it is the 'current' page we will have cleared
that bit ourselves, so skipping it is wrong. So: move the 'skip this page'
inside 'if page != lastpage'.
Also fold call of file_page_offset into the one place where the value (bit) is
used.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently we don't wait for updates to the bitmap to be flushed to disk
properly. The infrastructure all there, but it isn't being used....
A separate kernel thread (bitmap_writeback_daemon) is needed to wait for each
page as we cannot get callbacks when a page write completes.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- report sync_size properly - need /2 to convert sectors to KB
- move everything over 2 spaces to allow proper spelling of
"events cleared".
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
A u64 is not an unsigned long long. On power4 it is `long', and printk warns.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
As the array-wide clean bit (in the superblock) is set more agressively than
the bits in the bitmap are cleared, it is possible to have an array which is
clean despite there being bits set in the bitmap.
These bits will currently never get cleared, as they can only be cleared by a
resync pass, which never happens.
No, when reading bits from disk, be aware of whether the whole array is known
to be in sync, and act accordingly.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The debugging message printed the wrong pid, which didn't help remove bugs....
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
bitmap_daemon_work clears bits in the bitmap for blocks that haven't been
written to for a while. It needs to be called regularly to make sure the
bitmap doesn't endup full of ones .... but it wasn't.
So call it from the increasingly-inaptly-named md_check_recovery
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
1/ When init from disk, it is a BUG if there is nowhere
to init from,
2/ use seq_path to print path in /proc/mdstat
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With this patch, the intent to write to some block in the array can be logged
to a bitmap file. Each bit represents some number of sectors and is set
before any update happens, and only cleared when all writes relating to all
sectors are complete.
After an unclean shutdown, information in this bitmap can be used to optimise
resync - only sectors which could be out-of-sync need to be updated.
Also if a drive is removed and then added back into an array, the recovery can
make use of the bitmap to optimise reconstruction. This is not implemented in
this patch.
Currently the bitmap is stored in a file which must (obviously) be stored on a
separate device.
The patch only provided infrastructure. It does not update any personalities
to bitmap intent logging.
Md arrays can still be used with no bitmap file. This patch has minimal
impact on such arrays.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
1/ change the return value (which is number-of-sectors synced)
from 'int' to 'sector_t'.
The number of sectors is usually easily small enough to fit
in an int, but if resync needs to abort, it may want to return
the total number of remaining sectors, which could be large.
Also errors cannot be returned as negative numbers now, so use
0 instead
2/ Add a 'skipped' return parameter to allow the array to report
that it skipped the sectors. This allows md to take this into account
in the speed calculations.
Currently there is no important skipping, but the bitmap-based-resync
that is coming will use this.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When md marks the superblock dirty before a write, it calls
generic_make_request (to write the superblock) from within
generic_make_request (to write the first dirty block), which could cause
problems later.
With this patch, the superblock write is always done by the helper thread, and
write request are delayed until that write completes.
Also, the locking around marking the array dirty and writing the superblock is
improved to avoid possible races.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
md_enter_safemode checks if it is time to mark the md superblock as 'clean'.
i.e. if all writes have completed and a suitable delay has passed.
This is currently called from md_handle_safemode which in-turn is called
(almost) every time md_check_recovery is called, and from the end of
md_do_sync which causes the mddev->thread to run, which will always call
md_check_recovery as well.
So it doesn't need to be a separate function and fits quite well into
md_check_recovery.
The "almost" is because multipathd calls md_check_recovery but not
md_handle_safemode. This is OK because the code from md_enter_safemode is a
no-op if mddev->safemode == 0, which it always is for a multipathd (providing
we don't allow it to be set to 2 on a signal...)
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently if add_new_disk is used to hot-add a drive to a degraded array,
recovery doesn't start ... because we didn't tell it to.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
is changed
i.e. missing or failed drives are moved to the end of the list. The means
a 3 drive md array with the first drive missing can be shrunk to a two
drive array. Currently that isn't possible.
Also, the "last_used" device number might be out-of-range after the number
of devices is reduced, so we set it to 0.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Several drivers miss filling in the access_align field. So this patch has
them fill it in.
Signed-off-by: James Simmons <jsimmons@www.infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Shrink the stack when calling the drawing alignment functions.
Signed-off-by: James Simmons <jsimmons@www.infradead.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Improve the fonts for use with the framebuffer.
I've added all the characters marked 'FIXME' in the sun12x22 font and
created a 10x18 font (based on the sun12x22 font) and a 7x14 font (based
on the vga8x16 font).
This patch is non-intrusive, no options are enabled by default so most
users won't notice a thing.
I am placing my changes under the GPL, however, I've not seen any copyright
notices on the sun12x22 font and the vga8x16 font which I derived my new
fonts from so I don't know what the copyright status is.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add support for the Arc monochrome LCD board.
The board uses KS108 controllers to drive individual 64x64 LCD matrices.
The board can be paneled in a variety of setups such as 2x1=128x64,
4x4=256x256 and so on. The board/host interface is through GPIO.
Signed-off-by: Jaya Kumar <jayalk@intworks.biz>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <linux-fbdev-devel@lists.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Changed the tests in intelfb_set_par to check also the parameter
var.accel_flags. If null, do nothing about ring buffers.
Now, the DirectFB i830 driver could nicely work even if intelfb is hw
accelerated. Just change the /etc/fb.modes file to disable console hw
acceleration when starting a DirectFB app.
Signed-off-by: Sylvain Meyer <sylvain.meyer@worldonline.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- Add voffset option to avoid conficts with Xorg i810 driver
Signed-off-by: Sylvain Meyer <sylvain.meyer@worldonline.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently when going from vgacon to fbcon the VT screenbuffer are often
different sizes. In the case when they are different sizes a new VT
screenbuffer is allocated and the contents are copied into the new buffer.
Currently the amount copied from VGA text memory to the new screenbuf is
the size of the framebuffer console. If the framebuffer console new VT
screen buffer is greater than the VGA text memory size then we get some of
the VGA BIOS contents as well.
This patch will only allow you to copy up to the size of VGA text memory
now. The rest is filled with erase characters.
Initial patch by Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: James Simmons <jsimmons@www.infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Since no one is using the inbuf, outbuf of struct fb_pixmap I removed their
use in the framebuffer console. The idea is instead move the pixmap
functionality below the accelerated functions intead of on top as the way
it is now. If there is no objection please apply. This is against Linus
latestr GIT tree. Thank you.
Signed-off-by: James Simmons <jsimmons@www.infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Can't use this fancy name, because it's used to generate a sysfs filename:
kobject_register failed for Intel(R) 830M/845G/852GM/855GM/865G/915G
Framebuffer Driver (-13)
[<c01bf8e3>] kobject_register+0x43/0x70
[<c022dfe2>] bus_add_driver+0x52/0xa0
[<c01c8c10>] pci_device_shutdown+0x0/0x20
[<c01c8d71>] pci_register_driver+0x61/0x80
[<c0387099>] intelfb_init+0x59/0x70
[<c03787cc>] do_initcalls+0x2c/0xc0
[<c0159025>] kern_mount+0x15/0x17
[<c01002a0>] init+0x0/0x100
[<c01002ca>] init+0x2a/0x100
[<c0100f58>] kernel_thread_helper+0x0/0x18
[<c0100f5d>] kernel_thread_helper+0x5/0x18
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix the size passed to release_mem_region in an error path.
Also adjust the message printed when vesafb cannot load; the comment there
already says this must not be fatal, so the message should also not mention
the word 'abort' otherwise indicating a problem to worry about in the log.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Gerd Knorr <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
s1d13xxxfb_remove() is referenced from s1d13xxxfb_probe(), which is marked
__devinit(). So s1d13xxxfb_remove() cannot be marked __devexit.
Does this all make sense? Clearly the __devexit section will still be in
core when the __devinit code is run, if the driver was loaded as a module.
But I suppose that if the driver is statically linked, the __devexit section
might be dropped early in boot. Still, we wouldn't drop __devexit prior to
initcall completion, at which point the __devinit code has all been run
anyway.
verdict: this code was legal and made sense. Is this a generic problem, or an
arm-specific problem?
UPD include/linux/compile.h
CC init/version.o
LD init/built-in.o
LD .tmp_vmlinux1
`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
I don't see any reason why the framebuffer should need to be cleared,
and it makes Tux vanish.
Cc: <linux-fbdev-devel@lists.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch fixes a race in the command reference counting logic by putting
spinlocks around kobject_put() in the command_put function.
- Also added debug messages.
- Changed a memcpy to memcpy_fromio since we are reading from io space.
Signed-off-by: Max Asbock <masbock@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch rewrites the handling of remote control events. Rather than making
them available from a special file in the ibmasmfs, now the events from the
RSA card get translated into kernel input events and injected into the input
subsystem. The driver now will generate two /dev/input/eventX nodes -- one
for the keyboard and one for the mouse. The mouse node generates absolute
events more like a touch pad than a mouse.
Signed-off-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Max Asbock <masbock@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Due to my incomplete understanding of the wait_event_interruptible() function
threads waiting for service processor events were not woken up. This patch
fixes that problem.
Signed-off-by: Max Asbock <masbock@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
First of a series of patches for the ibmasm driver. (that is the driver for
the IBM xSeries RSA service processor)
To summarize what they do:
[1] change a #define for the buffer size for commands
[2] Fix a bug where threads in the event handling code calling
wait_event_interruptible() weren't woken up as expected.
[3] Redesigned how remote mouse and keyboard events received by the driver
are handled.
[4] Fixed a race in the command reference counting logic.
This patch:
- change a #define for the buffer size for commands
Signed-off-by: Max Asbock <masbock@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix max channel check in cio_ignore display function.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch removes an obsolete header file include/asm-m32r/m32102peri.h.
In this header, there are some undesirable single character types, like V.
And the header is almost no longer used.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch is for the M32R CF/PCMCIA drivers to support a new platform,
Mappi-III evaluation board.
Signed-off-by: Mamoru Sakugawa <sakugawa@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Several hardware features of SGI's IOC4 I/O controller chip require
timing-related driver calculations dependent upon the PCI bus speed. This
patch enables the core IOC4 driver code to detect the actual bus speed and
store a value that can later be used by the IOC4 subdrivers as needed.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The SGI IOC4 I/O controller chip drivers are currently all configured by
CONFIG_BLK_DEV_SGIIOC4. This is undesirable as not all IOC4 hardware features
are needed by all systems.
This patch adds two configuration variables, CONFIG_SGI_IOC4 for core IOC4
driver support (see patch 1/3 in this series for further explanation) and
CONFIG_SERIAL_SGI_IOC4 to independently enable serial port support.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com>
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This series of patches reworks the configuration and internal structure
of the SGI IOC4 I/O controller device drivers.
These changes are motivated by several factors:
- The IOC4 chip PCI resources are of mixed use between functions (i.e.
multiple functions are handled in the same address range, sometimes
within the same register), muddling resource ownership and initialization
issues. Centralizing this ownership in a core driver is desirable.
- The IOC4 chip implements multiple functions (serial, IDE, others not
yet implemented in the mainline kernel) but is not a multifunction
PCI device. In order to properly handle device addition and removal
as well as module insertion and deletion, an intermediary IOC4-specific
driver layer is needed to handle these operations cleanly.
- All IOC4 drivers are currently enabled by a single CONFIG value. As
not all systems need all IOC4 functions, it is desireable to enable
these drivers independently.
- The current IOC4 core driver will trigger loading of all function-level
drivers, as it makes direct calls to them. This situation should be
reversed (i.e. function-level drivers cause loading of core driver)
in order to maintain a clear and least-surprise driver loading model.
- IOC4 hardware design necessitates some driver-level dependency on
the PCI bus clock speed. Current code assumes a 66MHz bus, but the
speed should be autodetected and appropriate compensation taken.
This patch series effects the above changes by a newly and better designed
IOC4 core driver with which the function-level drivers can register and
deregister themselves upon module insertion/removal. By tracking these
modules, device addition/removal is also handled properly. PCI resource
management and ownership issues are centralized in this core driver, and
IOC4-wide configuration actions such as bus speed detection are also
handled in this core driver.
This patch:
The SGI IOC4 I/O controller chip implements multiple functions, though it is
not a multi-function PCI device. Additionally, various PCI resources of the
IOC4 are shared by multiple hardware functions, and thus resource ownership by
driver is not clearly delineated. Due to the current driver design, all core
and subordinate drivers must be loaded, or none, which is undesirable if not
all IOC4 hardware features are being used.
This patch reorganizes the IOC4 drivers so that the core driver provides a
subdriver registration service. Through appropriate callbacks the subdrivers
can now handle device addition and removal, as well as module insertion and
deletion (though the IOC4 IDE driver requires further work before module
deletion will work). The core driver now takes care of allocating PCI
resources and data which must be shared between subdrivers, to clearly
delineate module ownership of these items.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add vr41xx gpio support.
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch allows iSeries to build with CONFIG_PCI=n. This is useful for
partitions that have only virtual I/O.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Adds SCC2 pin routing specific to the GP3 board.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove the superfluous test of "if (vortex_debug > 3)" inside the "if
(vortex_debug > 6)" clause early in boomerang_start_xmit.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch modifies the way pagesets in struct zone are managed.
Each zone has a per-cpu array of pagesets. So any particular CPU has some
memory in each zone structure which belongs to itself. Even if that CPU is
not local to that zone.
So the patch relocates the pagesets for each cpu to the node that is nearest
to the cpu instead of allocating the pagesets in the (possibly remote) target
zone. This means that the operations to manage pages on remote zone can be
done with information available locally.
We play a macro trick so that non-NUMA pmachines avoid the additional
pointer chase on the page allocator fastpath.
AIM7 benchmark on a 32 CPU SGI Altix
w/o patches:
Tasks jobs/min jti jobs/min/task real cpu
1 484.68 100 484.6769 12.01 1.97 Fri Mar 25 11:01:42 2005
100 27140.46 89 271.4046 21.44 148.71 Fri Mar 25 11:02:04 2005
200 30792.02 82 153.9601 37.80 296.72 Fri Mar 25 11:02:42 2005
300 32209.27 81 107.3642 54.21 451.34 Fri Mar 25 11:03:37 2005
400 34962.83 78 87.4071 66.59 588.97 Fri Mar 25 11:04:44 2005
500 31676.92 75 63.3538 91.87 742.71 Fri Mar 25 11:06:16 2005
600 36032.69 73 60.0545 96.91 885.44 Fri Mar 25 11:07:54 2005
700 35540.43 77 50.7720 114.63 1024.28 Fri Mar 25 11:09:49 2005
800 33906.70 74 42.3834 137.32 1181.65 Fri Mar 25 11:12:06 2005
900 34120.67 73 37.9119 153.51 1325.26 Fri Mar 25 11:14:41 2005
1000 34802.37 74 34.8024 167.23 1465.26 Fri Mar 25 11:17:28 2005
with slab API changes and pageset patch:
Tasks jobs/min jti jobs/min/task real cpu
1 485.00 100 485.0000 12.00 1.96 Fri Mar 25 11:46:18 2005
100 28000.96 89 280.0096 20.79 150.45 Fri Mar 25 11:46:39 2005
200 32285.80 79 161.4290 36.05 293.37 Fri Mar 25 11:47:16 2005
300 40424.15 84 134.7472 43.19 438.42 Fri Mar 25 11:47:59 2005
400 39155.01 79 97.8875 59.46 590.05 Fri Mar 25 11:48:59 2005
500 37881.25 82 75.7625 76.82 730.19 Fri Mar 25 11:50:16 2005
600 39083.14 78 65.1386 89.35 872.79 Fri Mar 25 11:51:46 2005
700 38627.83 77 55.1826 105.47 1022.46 Fri Mar 25 11:53:32 2005
800 39631.94 78 49.5399 117.48 1169.94 Fri Mar 25 11:55:30 2005
900 36903.70 79 41.0041 141.94 1310.78 Fri Mar 25 11:57:53 2005
1000 36201.23 77 36.2012 160.77 1458.31 Fri Mar 25 12:00:34 2005
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Shobhit Dayal <shobhit@calsoftinc.com>
Signed-off-by: Shai Fultheim <Shai@Scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch implements a number of smp_processor_id() cleanup ideas that
Arjan van de Ven and I came up with.
The previous __smp_processor_id/_smp_processor_id/smp_processor_id API
spaghetti was hard to follow both on the implementational and on the
usage side.
Some of the complexity arose from picking wrong names, some of the
complexity comes from the fact that not all architectures defined
__smp_processor_id.
In the new code, there are two externally visible symbols:
- smp_processor_id(): debug variant.
- raw_smp_processor_id(): nondebug variant. Replaces all existing
uses of _smp_processor_id() and __smp_processor_id(). Defined
by every SMP architecture in include/asm-*/smp.h.
There is one new internal symbol, dependent on DEBUG_PREEMPT:
- debug_smp_processor_id(): internal debug variant, mapped to
smp_processor_id().
Also, i moved debug_smp_processor_id() from lib/kernel_lock.c into a new
lib/smp_processor_id.c file. All related comments got updated and/or
clarified.
I have build/boot tested the following 8 .config combinations on x86:
{SMP,UP} x {PREEMPT,!PREEMPT} x {DEBUG_PREEMPT,!DEBUG_PREEMPT}
I have also build/boot tested x64 on UP/PREEMPT/DEBUG_PREEMPT. (Other
architectures are untested, but should work just fine.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix overrun of static array "ipmi_interfaces" of size 4 at position 4 with
index variable "if_num".
Definitions involved:
297 #define MAX_IPMI_INTERFACES 4
298 static ipmi_smi_t ipmi_interfaces[MAX_IPMI_INTERFACES];
Signed-off-by: Zaur Kambarov <zkambarov@coverity.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I think we need this patch or we might "lose" devices to the dpm_irq_off
list if a failure occurs during the suspend process.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Finally (phew!) this patch demonstrates how to adapt the adm1026 to
take advantage of the new callbacks, and the i2c-sysfs.h defined
structure/macros. Most of the other sensor/hwmon drivers could be
updated in the same way. The odd few exceptions (bmcsensors for
example) however might be better off with their own custom attribute
structure.
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
drivers/zorro/zorro-sysfs.c: update device attribute callbacks
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
drivers/usb/gadget/pxa2xx_udc.c: update device attribute callbacks
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
device attribute callbacks
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
drivers/s390/block/dcssblk.c: update device attribute callbacks
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
attribute callbacks
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
attribute callbacks
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
attribute callbacks
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
device attribute callbacks
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds the device_attribute paramerter to the
device_attribute store and show sysfs callback functions, and passes a
reference to the attribute when the callbacks are called.
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The error handling in bus_add_device() and device_attach() is simply
non-existing. This patch propagates any error from device_attach to
the upper layers to allow for a proper recovery.
From: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This adds a generic function 'unregister_node()'.
It is used to remove objects of a node going away
for hotplug. All the devices on the node must be
unregistered before calling this function.
Signed-off-by: Keiichiro Tokunaga <tokunaga.keiich@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -puN drivers/base/node.c~numa_hp_base drivers/base/node.c
|
|
This patch fixes usb_driver_release_interface() to make it avoid calling
device_release_driver() recursively, i.e., when invoked from within the
disconnect routine for the same device. The patch applies to your
"driver" tree.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch is intended for your "driver" tree. It fixes several subtle
races in driver_detach() and device_release_driver() in the driver-model
core.
The major change is to use klist_remove() rather than klist_del() when
taking a device off its driver's list. There's no other way to guarantee
that the list pointers will be updated before some other driver binds to
the device. For this to work driver_detach() can't use a klist iterator,
so the loop over the devices must be written out in full. In addition the
patch protects against the possibility that, when a driver and a device
are unregistered at the same time, one may be unloaded from memory before
the other is finished using it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The original code looks like this:
/* if interface was already added, bind now; else let
* the future device_add() bind it, bypassing probe()
*/
if (!list_empty (&dev->bus_list))
device_bind_driver(dev);
IOW, it's checking to see if the device is attached to the bus or not
and binding the driver if it is. It's checking the device's bus list,
which will only appear empty when the device has been initialized, but
not added. It depends way too much on the driver model internals, but it
seems to be the only way to do the weird crap they want to do with
interfaces.
When I converted it to use klists, I accidentally inverted the logic,
which led to bad things happening. This patch returns the check to its
orginal value.
From: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/usb.c
===================================================================
|
|
Fix a typo in scdrv_init() which was breaking the build for SGI sn2.
Signed-off-by: Jason Uhlenkott <jasonuhl@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There's no check to see if the device is already bound to a driver, which
could do bad things. The first thing to go wrong is that it will try to match
a driver with a device already bound to one. In some cases (it appears with
USB with drivers/usb/core/usb.c::usb_match_id()), some drivers will match a
device based on the class type, so it would be common (especially for HID
devices) to match a device that is already bound.
The fun comes when ->probe() is called, it fails, then
driver_probe_device() does this:
dev->driver = NULL;
Later on, that pointer could be be dereferenced without checking and cause
hell to break loose.
This problem could be nasty. It's very hardware dependent, since some
devices could have a different set of matching qualifiers than others.
Now, I don't quite see exactly where/how you were getting that crash.
You're dereferencing bad memory, but I'm not sure which pointer was bad
and where it came from, but it could have come from a couple of different
places.
The patch below will hopefully fix it all up for you. It's against
2.6.12-rc2-mm1, and does the following:
- Move logic to driver_probe_device() and comments uncommon returns:
1 - If device is bound
0 - If device not bound, and no error
error - If there was an error.
- Move locking to caller of that function, since we want to lock a
device for the entire time we're trying to bind it to a driver (to
prevent against a driver being loaded at the same time).
- Update __device_attach() and __driver_attach() to do that locking.
- Check if device is already bound in __driver_attach()
- Update the converse device_release_driver() so it locks the device
around all of the operations.
- Mark driver_probe_device() as static and remove export. It's an
internal function, it should stay that way, and there are no other
callers. If there is ever a need to export it, we can audit it as
necessary.
Signed-off-by: Andrew Morton <akpm@osdl.org>
|
|
Also stops looping over the lists when a match is found.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de
|
|
On Friday, March 25, 2005 8:47 PM Greg KH wrote:
>Here's a fix for pci express. For some reason I don't think they are
>using the driver model properly here, but I could be wrong...
Thanks for making the changes. However, changes in functions:
void pcie_port_device_remove(struct pci_dev *dev) and
static int remove_iter(struct device *dev, void *data)
are not correct. Please use the patch, which is based on kernel
2.6.12-rc1, below for a fix for these.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
nodemgr_remove_host_dev()
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -Nru a/drivers/ieee1394/nodemgr.c b/drivers/ieee1394/nodemgr.c
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/usb.c
===================================================================
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: linux-2.6.12-rc2/drivers/base/driver.c
===================================================================
|
|
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -Nru a/drivers/base/driver.c b/drivers/base/driver.c
|
|
- Use klist iterator in device_for_each_child(), making it safe to use for
removing devices.
- Remove unused list_to_dev() function.
- Kills all usage of devices_subsys.rwsem.
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
scsi_remove_target().
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/scsi/scsi_sysfs.c
===================================================================
|
|
- Can't wait on removing the current item in the list (the positive refcount *because*
we are using it causes it to deadlock).
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- Don't add devices to bus's embedded kset, since it's not used by anyone anymore.
- Don't need to take the bus rwsem when calling {device,driver}_attach(), since
those functions use the klists and the klists' spinlocks.
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
lists that will go away.
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/usb.c
===================================================================
|
|
- Now possible, since the lists are locked using the klist lock and not the
global rwsem.
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- Use it in driver_for_each_device() instead of the regular list_head and stop using
the bus's rwsem for protection.
- Use driver_for_each_device() in driver_detach() so we don't deadlock on the
bus's rwsem.
- Remove ->devices.
- Move klist access and sysfs link access out from under device's semaphore, since
they're synchronized through other means.
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- Use it in bus_for_each_drv().
- Use the klist spinlock instead of the bus rwsem.
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- Use it for bus_for_each_dev().
- Use the klist spinlock instead of the bus rwsem.
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/usb.c
===================================================================
|
|
manually walking list.
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -Nru a/drivers/pnp/driver.c b/drivers/pnp/driver.c
|
|
Now there's an iterator for accessing each device bound to a driver.
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: linux-2.6.12-rc2/drivers/base/driver.c
===================================================================
|
|
This relocates the driver binding/unbinding code to drivers/base/dd.c. This is done
for two reasons: One, it's not code related to the bus_type itself; it uses some from
that, some from devices, and some from drivers. And Two, it will make it easier to do
some of the upcoming lock removal on that code..
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This adds a per-device semaphore that is taken before every call from the core to a
driver method. This prevents e.g. simultaneous calls to the ->suspend() or ->resume()
and ->probe() or ->release(), potentially saving a whole lot of headaches.
It also moves us a step closer to removing the bus rwsem, since it protects the fields
in struct device that are modified by the core.
Signed-off-by: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
anymore.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Trivial fix to USB class-creation error path; please apply.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
class_simple
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
class_simple
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
of class_simple
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
class_simple
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
class_simple
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This moves a kref into the main hcd structure, which detaches it from
the class device structure.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
One step on improving the class api so that it can not be used incorrectly.
This also fixes the module owner issue with the dev files that happened when
the devt logic moved to the class core.
Based on a patch originally written by Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
sysfs: fix the rest of the kernel so if an attribute doesn't
implement show or store method read/write will return
-EIO instead of 0 or -EINVAL or -EPERM.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
sysfs: fix drivers/block so if an attribute doesn't implement
show or store method read/write will return -EIO
instead of 0 or -EINVAL.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
