Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Seems like we've had more fixes than usual this release cycle, but
  there's nothing in particular that we're doing differently.  Perhaps
  it's just one of those cycles where more people are finding more
  regressions (and/or that the latency of when people actually test
  what's been in the tree for a while is catching up so that we get the
  bug reports now).

  The bigger changes here are are for TI and Marvell platforms:
   * Timing changes for GPMC (generic localbus) on OMAP causing some
     largeish DTS deltas.
   * Fixes to window allocation on PCI for mvebu touching drivers/
     stuff.  Patches have acks from subsystem maintainers where needed.
   * A fix from Thomas for a botched DT conversion in drivers/edma.

  There's a handful of other fixes for the above platforms as well as
  sunxi, at91, i.MX.  I also included a MAINTAINER update for Broadcom,
  and a trivial move of a binding doc.

  I know you said you'd be offline this week, but I might as well post
  it for when you return.  :)"

I'm not quite offline yet.  Doing a few pulls in the last hour before my
internet goes away..

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
  MAINTAINERS: update Broadcom ARM tree location and add an SoC family
  ARM: dts: i.MX53: Fix ipu register space size
  ARM: dts: kirkwood: fix mislocated pcie-controller nodes
  ARM: sunxi: Enable GMAC in sunxi_defconfig
  ARM: common: edma: Fix xbar mapping
  ARM: sun7i: Fix i2c4 base address
  ARM: Kirkwood: T5325: Fix double probe of Codec
  ARM: mvebu: enable the SATA interface on Armada 375 DB
  ARM: mvebu: specify I2C bus frequency on Armada 370 DB
  ARM: mvebu: use qsgmii phy-mode for Armada XP GP interfaces
  ARM: mvebu: fix NOR bus-width in Armada XP OpenBlocks AX3 Device Tree
  ARM: mvebu: fix NOR bus-width in Armada XP DB Device Tree
  ARM: mvebu: fix NOR bus-width in Armada XP GP Device Tree
  ARM: dts: AM3517: Disable absent IPs inherited from OMAP3
  ARM: dts: OMAP2: Fix interrupts for OMAP2420 mailbox
  ARM: dts: OMAP5: Add mailbox dt node to fix boot warning
  ARM: OMAP5: Switch to THUMB mode if needed on secondary CPU
  ARM: dts: am437x-gp-evm: Do not reset gpio5
  ARM: dts: omap3-igep0020: use SMSC9221 timings
  PCI: mvebu: split PCIe BARs into multiple MBus windows when needed
  ...

42 files changed, 281 insertions, 207 deletions

diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt
index cd5e23912888cf..6794cdc96d8fdf 100644
--- a/Documentation/devicetree/bindings/clock/at91-clock.txt
+++ b/Documentation/devicetree/bindings/clock/at91-clock.txt
@@ -62,7 +62,7 @@ Required properties for PMC node:
 - interrupt-controller : tell that the PMC is an interrupt controller.
 - #interrupt-cells : must be set to 1. The first cell encodes the interrupt id,
 	and reflect the bit position in the PMC_ER/DR/SR registers.
-	You can use the dt macros defined in dt-bindings/clk/at91.h.
+	You can use the dt macros defined in dt-bindings/clock/at91.h.
 	0 (AT91_PMC_MOSCS) -> main oscillator ready
 	1 (AT91_PMC_LOCKA) -> PLL A ready
 	2 (AT91_PMC_LOCKB) -> PLL B ready
diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt
index 9fbbdb783a72d5..68ff2137bae726 100644
--- a/Documentation/devicetree/bindings/dma/ti-edma.txt
+++ b/Documentation/devicetree/bindings/dma/ti-edma.txt
@@ -29,6 +29,6 @@ edma: edma@49000000 {
 	dma-channels = <64>;
 	ti,edma-regions = <4>;
 	ti,edma-slots = <256>;
-	ti,edma-xbar-event-map = <1 12
-				  2 13>;
+	ti,edma-xbar-event-map = /bits/ 16 <1 12
+					    2 13>;
 };
diff --git a/MAINTAINERS b/MAINTAINERS
index 764075dd8d618c..c596b74b29d532 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1893,14 +1893,15 @@ L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/ethernet/broadcom/bnx2x/
 
-BROADCOM BCM281XX/BCM11XXX ARM ARCHITECTURE
+BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE
 M:	Christian Daudt <bcm@fixthebug.org>
 M:	Matt Porter <mporter@linaro.org>
 L:	bcm-kernel-feedback-list@broadcom.com
-T:	git git://git.github.com/broadcom/bcm11351
+T:	git git://github.com/broadcom/mach-bcm
 S:	Maintained
 F:	arch/arm/mach-bcm/
 F:	arch/arm/boot/dts/bcm113*
+F:	arch/arm/boot/dts/bcm216*
 F:	arch/arm/boot/dts/bcm281*
 F:	arch/arm/configs/bcm_defconfig
 F:	drivers/mmc/host/sdhci_bcm_kona.c
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index cb6811e5ae5a9a..7ad75b4e066358 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -144,7 +144,7 @@
 			compatible = "ti,edma3";
 			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
 			reg =	<0x49000000 0x10000>,
-				<0x44e10f90 0x10>;
+				<0x44e10f90 0x40>;
 			interrupts = <12 13 14>;
 			#dma-cells = <1>;
 			dma-channels = <64>;
diff --git a/arch/arm/boot/dts/am3517.dtsi b/arch/arm/boot/dts/am3517.dtsi
index 788391f9168441..5a452fdd7c5d97 100644
--- a/arch/arm/boot/dts/am3517.dtsi
+++ b/arch/arm/boot/dts/am3517.dtsi
@@ -62,5 +62,21 @@
 	};
 };
 
+&iva {
+	status = "disabled";
+};
+
+&mailbox {
+	status = "disabled";
+};
+
+&mmu_isp {
+	status = "disabled";
+};
+
+&smartreflex_mpu_iva {
+	status = "disabled";
+};
+
 /include/ "am35xx-clocks.dtsi"
 /include/ "omap36xx-am35xx-omap3430es2plus-clocks.dtsi"
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
index df8798e8bd255b..a055f7f0f14ae5 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -117,6 +117,11 @@
 	status = "okay";
 };
 
+&gpio5 {
+	status = "okay";
+	ti,no-reset-on-init;
+};
+
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vmmcsd_fixed>;
diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts
index 82f238a9063ffe..3383c4b6680357 100644
--- a/arch/arm/boot/dts/armada-370-db.dts
+++ b/arch/arm/boot/dts/armada-370-db.dts
@@ -67,6 +67,7 @@
 			i2c@11000 {
 				pinctrl-0 = <&i2c0_pins>;
 				pinctrl-names = "default";
+				clock-frequency = <100000>;
 				status = "okay";
 				audio_codec: audio-codec@4a {
 					compatible = "cirrus,cs42l51";
diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts
index 9378d3136b41d7..0451124e8ebf49 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/armada-375-db.dts
@@ -79,6 +79,11 @@
 				};
 			};
 
+			sata@a0000 {
+				status = "okay";
+				nr-ports = <2>;
+			};
+
 			nand: nand@d0000 {
 				pinctrl-0 = <&nand_pins>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts
index 448373c4b0e534..90f0bf6f92715c 100644
--- a/arch/arm/boot/dts/armada-xp-db.dts
+++ b/arch/arm/boot/dts/armada-xp-db.dts
@@ -49,7 +49,7 @@
 			/* Device Bus parameters are required */
 
 			/* Read parameters */
-			devbus,bus-width    = <8>;
+			devbus,bus-width    = <16>;
 			devbus,turn-off-ps  = <60000>;
 			devbus,badr-skew-ps = <0>;
 			devbus,acc-first-ps = <124000>;
diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts
index 61bda687f782f6..0c756421ae6aa5 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/armada-xp-gp.dts
@@ -59,7 +59,7 @@
 			/* Device Bus parameters are required */
 
 			/* Read parameters */
-			devbus,bus-width    = <8>;
+			devbus,bus-width    = <16>;
 			devbus,turn-off-ps  = <60000>;
 			devbus,badr-skew-ps = <0>;
 			devbus,acc-first-ps = <124000>;
@@ -146,22 +146,22 @@
 			ethernet@70000 {
 				status = "okay";
 				phy = <&phy0>;
-				phy-mode = "rgmii-id";
+				phy-mode = "qsgmii";
 			};
 			ethernet@74000 {
 				status = "okay";
 				phy = <&phy1>;
-				phy-mode = "rgmii-id";
+				phy-mode = "qsgmii";
 			};
 			ethernet@30000 {
 				status = "okay";
 				phy = <&phy2>;
-				phy-mode = "rgmii-id";
+				phy-mode = "qsgmii";
 			};
 			ethernet@34000 {
 				status = "okay";
 				phy = <&phy3>;
-				phy-mode = "rgmii-id";
+				phy-mode = "qsgmii";
 			};
 
 			/* Front-side USB slot */
diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
index 985948ce67b327..5d42feb3104983 100644
--- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
+++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
@@ -39,7 +39,7 @@
 			/* Device Bus parameters are required */
 
 			/* Read parameters */
-			devbus,bus-width    = <8>;
+			devbus,bus-width    = <16>;
 			devbus,turn-off-ps  = <60000>;
 			devbus,badr-skew-ps = <0>;
 			devbus,acc-first-ps = <124000>;
diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
index ce1375595e5f27..4537259ce5299b 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
@@ -34,7 +34,7 @@
 			};
 
 			spi0: spi@f0004000 {
-				cs-gpios = <&pioD 13 0>;
+				cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
 				status = "okay";
 			};
 
@@ -79,7 +79,7 @@
 			};
 
 			spi1: spi@f8008000 {
-				cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioD 16 0>;
+				cs-gpios = <&pioC 25 0>;
 				status = "okay";
 			};
 
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index e21dda0e898657..3be973e9889a2b 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -10,7 +10,7 @@
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 
 / {
 	model = "Atmel AT91SAM9261 family SoC";
diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 63e1784d272c55..92a52faebef77c 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -8,7 +8,7 @@
 
 #include "skeleton.dtsi"
 #include <dt-bindings/pinctrl/at91.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 
diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi
index 9c2bff2252d0d0..6a1bf4ff83d551 100644
--- a/arch/arm/boot/dts/imx53.dtsi
+++ b/arch/arm/boot/dts/imx53.dtsi
@@ -115,7 +115,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "fsl,imx53-ipu";
-			reg = <0x18000000 0x080000000>;
+			reg = <0x18000000 0x08000000>;
 			interrupts = <11 10>;
 			clocks = <&clks IMX5_CLK_IPU_GATE>,
 			         <&clks IMX5_CLK_IPU_DI0_GATE>,
diff --git a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
index 32c6fb4a11624c..b939f4f52d16a7 100644
--- a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
+++ b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
@@ -30,6 +30,16 @@
 		bootargs = "console=ttyS0,115200n8 earlyprintk";
 	};
 
+	mbus {
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+        };
+
 	ocp@f1000000 {
 		pinctrl@10000 {
 			pmx_usb_led: pmx-usb-led {
@@ -73,14 +83,6 @@
 		ehci@50000 {
 			status = "okay";
 		};
-
-		pcie-controller {
-			status = "okay";
-
-			pcie@1,0 {
-				status = "okay";
-			};
-		};
 	};
 
 	gpio-leds {
diff --git a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
index aa78c2d11fe738..e2cc85cc3b87e8 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
@@ -4,6 +4,16 @@
 / {
 	model = "ZyXEL NSA310";
 
+	mbus {
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+	};
+
 	ocp@f1000000 {
 		pinctrl: pinctrl@10000 {
 
@@ -26,14 +36,6 @@
 			status = "okay";
 			nr-ports = <2>;
 		};
-
-		pcie-controller {
-			status = "okay";
-
-			pcie@1,0 {
-				status = "okay";
-			};
-		};
 	};
 
 	gpio_poweroff {
diff --git a/arch/arm/boot/dts/kirkwood-t5325.dts b/arch/arm/boot/dts/kirkwood-t5325.dts
index 7d1c7677a18f18..0bd70d928c69ba 100644
--- a/arch/arm/boot/dts/kirkwood-t5325.dts
+++ b/arch/arm/boot/dts/kirkwood-t5325.dts
@@ -127,11 +127,6 @@
 
 		i2c@11000 {
 			status = "okay";
-
-			alc5621: alc5621@1a {
-				compatible = "realtek,alc5621";
-				reg = <0x1a>;
-			};
 		};
 
 		serial@12000 {
diff --git a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
index f577b7df9a29e4..521c587acaee9f 100644
--- a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
+++ b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
@@ -24,11 +24,10 @@
 		compatible = "smsc,lan9221", "smsc,lan9115";
 		bank-width = <2>;
 		gpmc,mux-add-data;
-		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <186>;
-		gpmc,cs-wr-off-ns = <186>;
-		gpmc,adv-on-ns = <12>;
-		gpmc,adv-rd-off-ns = <48>;
+		gpmc,cs-on-ns = <1>;
+		gpmc,cs-rd-off-ns = <180>;
+		gpmc,cs-wr-off-ns = <180>;
+		gpmc,adv-rd-off-ns = <18>;
 		gpmc,adv-wr-off-ns = <48>;
 		gpmc,oe-on-ns = <54>;
 		gpmc,oe-off-ns = <168>;
@@ -36,12 +35,10 @@
 		gpmc,we-off-ns = <168>;
 		gpmc,rd-cycle-ns = <186>;
 		gpmc,wr-cycle-ns = <186>;
-		gpmc,access-ns = <114>;
-		gpmc,page-burst-access-ns = <6>;
-		gpmc,bus-turnaround-ns = <12>;
-		gpmc,cycle2cycle-delay-ns = <18>;
-		gpmc,wr-data-mux-bus-ns = <90>;
-		gpmc,wr-access-ns = <186>;
+		gpmc,access-ns = <144>;
+		gpmc,page-burst-access-ns = <24>;
+		gpmc,bus-turnaround-ns = <90>;
+		gpmc,cycle2cycle-delay-ns = <90>;
 		gpmc,cycle2cycle-samecsen;
 		gpmc,cycle2cycle-diffcsen;
 		vddvario-supply = <&vddvario>;
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
index 22f35ea142c199..8f8c07da4ac148 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -71,13 +71,6 @@
 			interrupts = <58>;
 		};
 
-		mailbox: mailbox@48094000 {
-			compatible = "ti,omap2-mailbox";
-			ti,hwmods = "mailbox";
-			reg = <0x48094000 0x200>;
-			interrupts = <26>;
-		};
-
 		intc: interrupt-controller@1 {
 			compatible = "ti,omap2-intc";
 			interrupt-controller;
diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/omap2420.dtsi
index 85b1fb014c4314..2d9979835f241f 100644
--- a/arch/arm/boot/dts/omap2420.dtsi
+++ b/arch/arm/boot/dts/omap2420.dtsi
@@ -125,6 +125,14 @@
 			dma-names = "tx", "rx";
 		};
 
+		mailbox: mailbox@48094000 {
+			compatible = "ti,omap2-mailbox";
+			reg = <0x48094000 0x200>;
+			interrupts = <26>, <34>;
+			interrupt-names = "dsp", "iva";
+			ti,hwmods = "mailbox";
+		};
+
 		timer1: timer@48028000 {
 			compatible = "ti,omap2420-timer";
 			reg = <0x48028000 0x400>;
diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi
index d09697dab55e80..42d2c61c9e2d7d 100644
--- a/arch/arm/boot/dts/omap2430.dtsi
+++ b/arch/arm/boot/dts/omap2430.dtsi
@@ -216,6 +216,13 @@
 			dma-names = "tx", "rx";
 		};
 
+		mailbox: mailbox@48094000 {
+			compatible = "ti,omap2-mailbox";
+			reg = <0x48094000 0x200>;
+			interrupts = <26>;
+			ti,hwmods = "mailbox";
+		};
+
 		timer1: timer@49018000 {
 			compatible = "ti,omap2420-timer";
 			reg = <0x49018000 0x400>;
diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
index d00055809e31d7..25ba08331d8852 100644
--- a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
+++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
@@ -10,18 +10,6 @@
 			cpu0-supply = <&vcc>;
 		};
 	};
-
-	vddvario: regulator-vddvario {
-		compatible = "regulator-fixed";
-		regulator-name = "vddvario";
-		regulator-always-on;
-	};
-
-	vdd33a: regulator-vdd33a {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd33a";
-		regulator-always-on;
-	};
 };
 
 &omap3_pmx_core {
@@ -35,58 +23,34 @@
 
  	hsusb0_pins: pinmux_hsusb0_pins {
 		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_clk.hsusb0_clk */
-			OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_stp.hsusb0_stp */
-			OMAP3_CORE1_IOPAD(0x21a4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */
-			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */
-			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data0.hsusb2_data0 */
-			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */
-			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */
-			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data3 */
-			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data4 */
-			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data5 */
-			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data6 */
-			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
+			OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_clk.hsusb0_clk */
+			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_stp.hsusb0_stp */
+			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */
+			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */
+			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data0.hsusb2_data0 */
+			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */
+			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */
+			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data3 */
+			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data4 */
+			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data5 */
+			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data6 */
+			OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
 		>;
 	};
 };
 
+#include "omap-gpmc-smsc911x.dtsi"
+
 &gpmc {
 	ranges = <5 0 0x2c000000 0x01000000>;
 
-	smsc1: ethernet@5,0 {
+	smsc1: ethernet@gpmc {
 		compatible = "smsc,lan9221", "smsc,lan9115";
 		pinctrl-names = "default";
 		pinctrl-0 = <&smsc1_pins>;
 		interrupt-parent = <&gpio6>;
 		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		reg = <5 0 0xff>;
-		bank-width = <2>;
-		gpmc,mux-add-data;
-		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <186>;
-		gpmc,cs-wr-off-ns = <186>;
-		gpmc,adv-on-ns = <12>;
-		gpmc,adv-rd-off-ns = <48>;
-		gpmc,adv-wr-off-ns = <48>;
-		gpmc,oe-on-ns = <54>;
-		gpmc,oe-off-ns = <168>;
-		gpmc,we-on-ns = <54>;
-		gpmc,we-off-ns = <168>;
-		gpmc,rd-cycle-ns = <186>;
-		gpmc,wr-cycle-ns = <186>;
-		gpmc,access-ns = <114>;
-		gpmc,page-burst-access-ns = <6>;
-		gpmc,bus-turnaround-ns = <12>;
-		gpmc,cycle2cycle-delay-ns = <18>;
-		gpmc,wr-data-mux-bus-ns = <90>;
-		gpmc,wr-access-ns = <186>;
-		gpmc,cycle2cycle-samecsen;
-		gpmc,cycle2cycle-diffcsen;
-		vddvario-supply = <&vddvario>;
-		vdd33a-supply = <&vdd33a>;
-		reg-io-width = <4>;
-		smsc,save-mac-address;
 	};
 };
 
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index b97736d98a6427..e2d163bf061975 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -107,7 +107,7 @@
 		>;
 	};
 
-	smsc911x_pins: pinmux_smsc911x_pins {
+	smsc9221_pins: pinmux_smsc9221_pins {
 		pinctrl-single,pins = <
 			0x1a2 (PIN_INPUT | MUX_MODE4)		/* mcspi1_cs2.gpio_176 */
 		>;
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index 7abd64f6ae2146..b22caaaf774ba7 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -10,7 +10,7 @@
  */
 
 #include "omap3-igep.dtsi"
-#include "omap-gpmc-smsc911x.dtsi"
+#include "omap-gpmc-smsc9221.dtsi"
 
 / {
 	model = "IGEPv2 (TI OMAP AM/DM37x)";
@@ -248,7 +248,7 @@
 
 	ethernet@gpmc {
 		pinctrl-names = "default";
-		pinctrl-0 = <&smsc911x_pins>;
+		pinctrl-0 = <&smsc9221_pins>;
 		reg = <5 0 0xff>;
 		interrupt-parent = <&gpio6>;
 		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm/boot/dts/omap3-sb-t35.dtsi b/arch/arm/boot/dts/omap3-sb-t35.dtsi
index 7909c51b05a564..d59e3de1441e2f 100644
--- a/arch/arm/boot/dts/omap3-sb-t35.dtsi
+++ b/arch/arm/boot/dts/omap3-sb-t35.dtsi
@@ -2,20 +2,6 @@
  * Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
  */
 
-/ {
-	vddvario_sb_t35: regulator-vddvario-sb-t35 {
-		compatible = "regulator-fixed";
-		regulator-name = "vddvario";
-		regulator-always-on;
-	};
-
-	vdd33a_sb_t35: regulator-vdd33a-sb-t35 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd33a";
-		regulator-always-on;
-	};
-};
-
 &omap3_pmx_core {
 	smsc2_pins: pinmux_smsc2_pins {
 		pinctrl-single,pins = <
@@ -37,11 +23,10 @@
 		reg = <4 0 0xff>;
 		bank-width = <2>;
 		gpmc,mux-add-data;
-		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <186>;
-		gpmc,cs-wr-off-ns = <186>;
-		gpmc,adv-on-ns = <12>;
-		gpmc,adv-rd-off-ns = <48>;
+		gpmc,cs-on-ns = <1>;
+		gpmc,cs-rd-off-ns = <180>;
+		gpmc,cs-wr-off-ns = <180>;
+		gpmc,adv-rd-off-ns = <18>;
 		gpmc,adv-wr-off-ns = <48>;
 		gpmc,oe-on-ns = <54>;
 		gpmc,oe-off-ns = <168>;
@@ -49,16 +34,14 @@
 		gpmc,we-off-ns = <168>;
 		gpmc,rd-cycle-ns = <186>;
 		gpmc,wr-cycle-ns = <186>;
-		gpmc,access-ns = <114>;
-		gpmc,page-burst-access-ns = <6>;
-		gpmc,bus-turnaround-ns = <12>;
-		gpmc,cycle2cycle-delay-ns = <18>;
-		gpmc,wr-data-mux-bus-ns = <90>;
-		gpmc,wr-access-ns = <186>;
+		gpmc,access-ns = <144>;
+		gpmc,page-burst-access-ns = <24>;
+		gpmc,bus-turnaround-ns = <90>;
+		gpmc,cycle2cycle-delay-ns = <90>;
 		gpmc,cycle2cycle-samecsen;
 		gpmc,cycle2cycle-diffcsen;
-		vddvario-supply = <&vddvario_sb_t35>;
-		vdd33a-supply = <&vdd33a_sb_t35>;
+		vddvario-supply = <&vddvario>;
+		vdd33a-supply = <&vdd33a>;
 		reg-io-width = <4>;
 		smsc,save-mac-address;
 	};
diff --git a/arch/arm/boot/dts/omap3-sbc-t3517.dts b/arch/arm/boot/dts/omap3-sbc-t3517.dts
index 024c9c6c682d7e..42189b65d393d2 100644
--- a/arch/arm/boot/dts/omap3-sbc-t3517.dts
+++ b/arch/arm/boot/dts/omap3-sbc-t3517.dts
@@ -8,6 +8,19 @@
 / {
 	model = "CompuLab SBC-T3517 with CM-T3517";
 	compatible = "compulab,omap3-sbc-t3517", "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+
+	/* Only one GPMC smsc9220 on SBC-T3517, CM-T3517 uses am35x Ethernet */
+	vddvario: regulator-vddvario-sb-t35 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
+	};
+
+	vdd33a: regulator-vdd33a-sb-t35 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd33a";
+		regulator-always-on;
+	};
 };
 
 &omap3_pmx_core {
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index acb9019dc437b6..4231191ade06ac 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -61,7 +61,7 @@
 			ti,hwmods = "mpu";
 		};
 
-		iva {
+		iva: iva {
 			compatible = "ti,iva2.2";
 			ti,hwmods = "iva";
 
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index f8c9855ce587c1..36b4312a5e0d82 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -630,6 +630,13 @@
 			status = "disabled";
 		};
 
+		mailbox: mailbox@4a0f4000 {
+			compatible = "ti,omap4-mailbox";
+			reg = <0x4a0f4000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mailbox";
+		};
+
 		timer1: timer@4ae18000 {
 			compatible = "ti,omap5430-timer";
 			reg = <0x4ae18000 0x80>;
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index eabcfdbb403acc..a106b0872910da 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -13,7 +13,7 @@
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 
 / {
 	model = "Atmel SAMA5D3 family SoC";
diff --git a/arch/arm/boot/dts/sama5d3_mci2.dtsi b/arch/arm/boot/dts/sama5d3_mci2.dtsi
index b029fe7ef17a65..1b02208ea6ff2b 100644
--- a/arch/arm/boot/dts/sama5d3_mci2.dtsi
+++ b/arch/arm/boot/dts/sama5d3_mci2.dtsi
@@ -9,7 +9,7 @@
 
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 
 / {
 	ahb {
diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
index 382b04431f66b6..02848453ca0cf5 100644
--- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi
+++ b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
@@ -9,7 +9,7 @@
 
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 
 / {
 	aliases {
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index a9fa75e4165205..7a8d4c6115f72f 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -9,7 +9,7 @@
 
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 
 / {
 	aliases {
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 32efc105df834d..aba1c8a3f38833 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -87,7 +87,7 @@
 
 		pll4: clk@01c20018 {
 			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-pll1-clk";
+			compatible = "allwinner,sun7i-a20-pll4-clk";
 			reg = <0x01c20018 0x4>;
 			clocks = <&osc24M>;
 			clock-output-names = "pll4";
@@ -109,6 +109,14 @@
 			clock-output-names = "pll6_sata", "pll6_other", "pll6";
 		};
 
+		pll8: clk@01c20040 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun7i-a20-pll4-clk";
+			reg = <0x01c20040 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll8";
+		};
+
 		cpu: cpu@01c20054 {
 			#clock-cells = <0>;
 			compatible = "allwinner,sun4i-a10-cpu-clk";
@@ -805,9 +813,9 @@
 			status = "disabled";
 		};
 
-		i2c4: i2c@01c2bc00 {
+		i2c4: i2c@01c2c000 {
 			compatible = "allwinner,sun4i-i2c";
-			reg = <0x01c2bc00 0x400>;
+			reg = <0x01c2c000 0x400>;
 			interrupts = <0 89 4>;
 			clocks = <&apb1_gates 15>;
 			clock-frequency = <100000>;
diff --git a/arch/arm/common/edma.c b/arch/arm/common/edma.c
index 41bca32409fce8..5339009b3c0ce6 100644
--- a/arch/arm/common/edma.c
+++ b/arch/arm/common/edma.c
@@ -1423,55 +1423,38 @@ EXPORT_SYMBOL(edma_clear_event);
 
 #if IS_ENABLED(CONFIG_OF) && IS_ENABLED(CONFIG_DMADEVICES)
 
-static int edma_of_read_u32_to_s16_array(const struct device_node *np,
-					 const char *propname, s16 *out_values,
-					 size_t sz)
+static int edma_xbar_event_map(struct device *dev, struct device_node *node,
+			       struct edma_soc_info *pdata, size_t sz)
 {
-	int ret;
-
-	ret = of_property_read_u16_array(np, propname, out_values, sz);
-	if (ret)
-		return ret;
-
-	/* Terminate it */
-	*out_values++ = -1;
-	*out_values++ = -1;
-
-	return 0;
-}
-
-static int edma_xbar_event_map(struct device *dev,
-			       struct device_node *node,
-			       struct edma_soc_info *pdata, int len)
-{
-	int ret, i;
+	const char pname[] = "ti,edma-xbar-event-map";
 	struct resource res;
 	void __iomem *xbar;
-	const s16 (*xbar_chans)[2];
+	s16 (*xbar_chans)[2];
+	size_t nelm = sz / sizeof(s16);
 	u32 shift, offset, mux;
+	int ret, i;
 
-	xbar_chans = devm_kzalloc(dev,
-				  len/sizeof(s16) + 2*sizeof(s16),
-				  GFP_KERNEL);
+	xbar_chans = devm_kzalloc(dev, (nelm + 2) * sizeof(s16), GFP_KERNEL);
 	if (!xbar_chans)
 		return -ENOMEM;
 
 	ret = of_address_to_resource(node, 1, &res);
 	if (ret)
-		return -EIO;
+		return -ENOMEM;
 
 	xbar = devm_ioremap(dev, res.start, resource_size(&res));
 	if (!xbar)
 		return -ENOMEM;
 
-	ret = edma_of_read_u32_to_s16_array(node,
-					    "ti,edma-xbar-event-map",
-					    (s16 *)xbar_chans,
-					    len/sizeof(u32));
+	ret = of_property_read_u16_array(node, pname, (u16 *)xbar_chans, nelm);
 	if (ret)
 		return -EIO;
 
-	for (i = 0; xbar_chans[i][0] != -1; i++) {
+	/* Invalidate last entry for the other user of this mess */
+	nelm >>= 1;
+	xbar_chans[nelm][0] = xbar_chans[nelm][1] = -1;
+
+	for (i = 0; i < nelm; i++) {
 		shift = (xbar_chans[i][1] & 0x03) << 3;
 		offset = xbar_chans[i][1] & 0xfffffffc;
 		mux = readl(xbar + offset);
@@ -1480,8 +1463,7 @@ static int edma_xbar_event_map(struct device *dev,
 		writel(mux, (xbar + offset));
 	}
 
-	pdata->xbar_chans = xbar_chans;
-
+	pdata->xbar_chans = (const s16 (*)[2]) xbar_chans;
 	return 0;
 }
 
diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig
index b5df4a511b0acd..81ba78eaf54adb 100644
--- a/arch/arm/configs/sunxi_defconfig
+++ b/arch/arm/configs/sunxi_defconfig
@@ -37,7 +37,7 @@ CONFIG_SUN4I_EMAC=y
 # CONFIG_NET_VENDOR_NATSEMI is not set
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_STMMAC_ETH=y
 # CONFIG_NET_VENDOR_WIZNET is not set
 # CONFIG_WLAN is not set
 CONFIG_SERIAL_8250=y
diff --git a/arch/arm/mach-omap2/omap-headsmp.S b/arch/arm/mach-omap2/omap-headsmp.S
index 75e92952c18efe..40c5d5f1451cd3 100644
--- a/arch/arm/mach-omap2/omap-headsmp.S
+++ b/arch/arm/mach-omap2/omap-headsmp.S
@@ -1,7 +1,7 @@
 /*
  * Secondary CPU startup routine source file.
  *
- * Copyright (C) 2009 Texas Instruments, Inc.
+ * Copyright (C) 2009-2014 Texas Instruments, Inc.
  *
  * Author:
  *      Santosh Shilimkar <santosh.shilimkar@ti.com>
@@ -28,9 +28,13 @@
  * code.  This routine also provides a holding flag into which
  * secondary core is held until we're ready for it to initialise.
  * The primary core will update this flag using a hardware
-+ * register AuxCoreBoot0.
+ * register AuxCoreBoot0.
  */
 ENTRY(omap5_secondary_startup)
+.arm
+THUMB( adr     r9, BSYM(wait)  )       @ CPU may be entered in ARM mode.
+THUMB( bx      r9              )       @ If this is a Thumb-2 kernel,
+THUMB( .thumb                  )       @ switch to Thumb now.
 wait:	ldr	r2, =AUX_CORE_BOOT0_PA	@ read from AuxCoreBoot0
 	ldr	r0, [r2]
 	mov	r0, r0, lsr #5
diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h
index f565f9944af2ee..7548db2bfb8a7e 100644
--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -21,7 +21,7 @@ struct mv_sata_platform_data;
 #define ORION_MBUS_DEVBUS_BOOT_ATTR   0x0f
 #define ORION_MBUS_DEVBUS_TARGET(cs)  0x01
 #define ORION_MBUS_DEVBUS_ATTR(cs)    (~(1 << cs))
-#define ORION_MBUS_SRAM_TARGET        0x00
+#define ORION_MBUS_SRAM_TARGET        0x09
 #define ORION_MBUS_SRAM_ATTR          0x00
 
 /*
diff --git a/drivers/bus/mvebu-mbus.c b/drivers/bus/mvebu-mbus.c
index 293e2e0a0a87c7..00b73448b22ea7 100644
--- a/drivers/bus/mvebu-mbus.c
+++ b/drivers/bus/mvebu-mbus.c
@@ -56,6 +56,7 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/debugfs.h>
+#include <linux/log2.h>
 
 /*
  * DDR target is the same on all platforms.
@@ -222,12 +223,6 @@ static int mvebu_mbus_window_conflicts(struct mvebu_mbus_state *mbus,
 		 */
 		if ((u64)base < wend && end > wbase)
 			return 0;
-
-		/*
-		 * Check if target/attribute conflicts
-		 */
-		if (target == wtarget && attr == wattr)
-			return 0;
 	}
 
 	return 1;
@@ -266,6 +261,17 @@ static int mvebu_mbus_setup_window(struct mvebu_mbus_state *mbus,
 		mbus->soc->win_cfg_offset(win);
 	u32 ctrl, remap_addr;
 
+	if (!is_power_of_2(size)) {
+		WARN(true, "Invalid MBus window size: 0x%zx\n", size);
+		return -EINVAL;
+	}
+
+	if ((base & (phys_addr_t)(size - 1)) != 0) {
+		WARN(true, "Invalid MBus base/size: %pa len 0x%zx\n", &base,
+		     size);
+		return -EINVAL;
+	}
+
 	ctrl = ((size - 1) & WIN_CTRL_SIZE_MASK) |
 		(attr << WIN_CTRL_ATTR_SHIFT)    |
 		(target << WIN_CTRL_TGT_SHIFT)   |
@@ -413,6 +419,10 @@ static int mvebu_devs_debug_show(struct seq_file *seq, void *v)
 			   win, (unsigned long long)wbase,
 			   (unsigned long long)(wbase + wsize), wtarget, wattr);
 
+		if (!is_power_of_2(wsize) ||
+		    ((wbase & (u64)(wsize - 1)) != 0))
+			seq_puts(seq, " (Invalid base/size!!)");
+
 		if (win < mbus->soc->num_remappable_wins) {
 			seq_printf(seq, " (remap %016llx)\n",
 				   (unsigned long long)wremap);
diff --git a/drivers/memory/mvebu-devbus.c b/drivers/memory/mvebu-devbus.c
index 110c03627051cb..b59a17fb7c3e3f 100644
--- a/drivers/memory/mvebu-devbus.c
+++ b/drivers/memory/mvebu-devbus.c
@@ -108,8 +108,19 @@ static int devbus_set_timing_params(struct devbus *devbus,
 			node->full_name);
 		return err;
 	}
-	/* Convert bit width to byte width */
-	r.bus_width /= 8;
+
+	/*
+	 * The bus width is encoded into the register as 0 for 8 bits,
+	 * and 1 for 16 bits, so we do the necessary conversion here.
+	 */
+	if (r.bus_width == 8)
+		r.bus_width = 0;
+	else if (r.bus_width == 16)
+		r.bus_width = 1;
+	else {
+		dev_err(devbus->dev, "invalid bus width %d\n", r.bus_width);
+		return -EINVAL;
+	}
 
 	err = get_timing_param_ps(devbus, node, "devbus,badr-skew-ps",
 				 &r.badr_skew);
diff --git a/drivers/pci/host/pci-mvebu.c b/drivers/pci/host/pci-mvebu.c
index d3d1cfd51e095f..e384e253459473 100644
--- a/drivers/pci/host/pci-mvebu.c
+++ b/drivers/pci/host/pci-mvebu.c
@@ -293,6 +293,58 @@ static int mvebu_pcie_hw_wr_conf(struct mvebu_pcie_port *port,
 	return PCIBIOS_SUCCESSFUL;
 }
 
+/*
+ * Remove windows, starting from the largest ones to the smallest
+ * ones.
+ */
+static void mvebu_pcie_del_windows(struct mvebu_pcie_port *port,
+				   phys_addr_t base, size_t size)
+{
+	while (size) {
+		size_t sz = 1 << (fls(size) - 1);
+
+		mvebu_mbus_del_window(base, sz);
+		base += sz;
+		size -= sz;
+	}
+}
+
+/*
+ * MBus windows can only have a power of two size, but PCI BARs do not
+ * have this constraint. Therefore, we have to split the PCI BAR into
+ * areas each having a power of two size. We start from the largest
+ * one (i.e highest order bit set in the size).
+ */
+static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port,
+				   unsigned int target, unsigned int attribute,
+				   phys_addr_t base, size_t size,
+				   phys_addr_t remap)
+{
+	size_t size_mapped = 0;
+
+	while (size) {
+		size_t sz = 1 << (fls(size) - 1);
+		int ret;
+
+		ret = mvebu_mbus_add_window_remap_by_id(target, attribute, base,
+							sz, remap);
+		if (ret) {
+			dev_err(&port->pcie->pdev->dev,
+				"Could not create MBus window at 0x%x, size 0x%x: %d\n",
+				base, sz, ret);
+			mvebu_pcie_del_windows(port, base - size_mapped,
+					       size_mapped);
+			return;
+		}
+
+		size -= sz;
+		size_mapped += sz;
+		base += sz;
+		if (remap != MVEBU_MBUS_NO_REMAP)
+			remap += sz;
+	}
+}
+
 static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
 {
 	phys_addr_t iobase;
@@ -304,8 +356,8 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
 
 		/* If a window was configured, remove it */
 		if (port->iowin_base) {
-			mvebu_mbus_del_window(port->iowin_base,
-					      port->iowin_size);
+			mvebu_pcie_del_windows(port, port->iowin_base,
+					       port->iowin_size);
 			port->iowin_base = 0;
 			port->iowin_size = 0;
 		}
@@ -331,11 +383,11 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
 	port->iowin_base = port->pcie->io.start + iobase;
 	port->iowin_size = ((0xFFF | ((port->bridge.iolimit & 0xF0) << 8) |
 			    (port->bridge.iolimitupper << 16)) -
-			    iobase);
+			    iobase) + 1;
 
-	mvebu_mbus_add_window_remap_by_id(port->io_target, port->io_attr,
-					  port->iowin_base, port->iowin_size,
-					  iobase);
+	mvebu_pcie_add_windows(port, port->io_target, port->io_attr,
+			       port->iowin_base, port->iowin_size,
+			       iobase);
 }
 
 static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
@@ -346,8 +398,8 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
 
 		/* If a window was configured, remove it */
 		if (port->memwin_base) {
-			mvebu_mbus_del_window(port->memwin_base,
-					      port->memwin_size);
+			mvebu_pcie_del_windows(port, port->memwin_base,
+					       port->memwin_size);
 			port->memwin_base = 0;
 			port->memwin_size = 0;
 		}
@@ -364,10 +416,11 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
 	port->memwin_base  = ((port->bridge.membase & 0xFFF0) << 16);
 	port->memwin_size  =
 		(((port->bridge.memlimit & 0xFFF0) << 16) | 0xFFFFF) -
-		port->memwin_base;
+		port->memwin_base + 1;
 
-	mvebu_mbus_add_window_by_id(port->mem_target, port->mem_attr,
-				    port->memwin_base, port->memwin_size);
+	mvebu_pcie_add_windows(port, port->mem_target, port->mem_attr,
+			       port->memwin_base, port->memwin_size,
+			       MVEBU_MBUS_NO_REMAP);
 }
 
 /*
@@ -743,14 +796,21 @@ static resource_size_t mvebu_pcie_align_resource(struct pci_dev *dev,
 
 	/*
 	 * On the PCI-to-PCI bridge side, the I/O windows must have at
-	 * least a 64 KB size and be aligned on their size, and the
-	 * memory windows must have at least a 1 MB size and be
-	 * aligned on their size
+	 * least a 64 KB size and the memory windows must have at
+	 * least a 1 MB size. Moreover, MBus windows need to have a
+	 * base address aligned on their size, and their size must be
+	 * a power of two. This means that if the BAR doesn't have a
+	 * power of two size, several MBus windows will actually be
+	 * created. We need to ensure that the biggest MBus window
+	 * (which will be the first one) is aligned on its size, which
+	 * explains the rounddown_pow_of_two() being done here.
 	 */
 	if (res->flags & IORESOURCE_IO)
-		return round_up(start, max_t(resource_size_t, SZ_64K, size));
+		return round_up(start, max_t(resource_size_t, SZ_64K,
+					     rounddown_pow_of_two(size)));
 	else if (res->flags & IORESOURCE_MEM)
-		return round_up(start, max_t(resource_size_t, SZ_1M, size));
+		return round_up(start, max_t(resource_size_t, SZ_1M,
+					     rounddown_pow_of_two(size)));
 	else
 		return start;
 }
diff --git a/include/dt-bindings/clk/at91.h b/include/dt-bindings/clock/at91.h
index 0b4cb999a3f7a2..0b4cb999a3f7a2 100644
--- a/include/dt-bindings/clk/at91.h
+++ b/include/dt-bindings/clock/at91.h