diff options
Diffstat (limited to 'drivers/usb/core/hub.c')
-rw-r--r-- | drivers/usb/core/hub.c | 505 |
1 files changed, 259 insertions, 246 deletions
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index a739403a9e455a..3c54b218301c16 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -614,6 +614,29 @@ static int hub_ext_port_status(struct usb_hub *hub, int port1, int type, ret = 0; } mutex_unlock(&hub->status_mutex); + + /* + * There is no need to lock status_mutex here, because status_mutex + * protects hub->status, and the phy driver only checks the port + * status without changing the status. + */ + if (!ret) { + struct usb_device *hdev = hub->hdev; + + /* + * Only roothub will be notified of port state changes, + * since the USB PHY only cares about changes at the next + * level. + */ + if (is_root_hub(hdev)) { + struct usb_hcd *hcd = bus_to_hcd(hdev->bus); + + if (hcd->usb_phy) + usb_phy_notify_port_status(hcd->usb_phy, + port1 - 1, *status, *change); + } + } + return ret; } @@ -2117,22 +2140,6 @@ EXPORT_SYMBOL_GPL(usb_set_device_state); * USB-3.0 buses the address is assigned by the controller hardware * and it usually is not the same as the device number. * - * WUSB devices are simple: they have no hubs behind, so the mapping - * device <-> virtual port number becomes 1:1. Why? to simplify the - * life of the device connection logic in - * drivers/usb/wusbcore/devconnect.c. When we do the initial secret - * handshake we need to assign a temporary address in the unauthorized - * space. For simplicity we use the first virtual port number found to - * be free [drivers/usb/wusbcore/devconnect.c:wusbhc_devconnect_ack()] - * and that becomes it's address [X < 128] or its unauthorized address - * [X | 0x80]. - * - * We add 1 as an offset to the one-based USB-stack port number - * (zero-based wusb virtual port index) for two reasons: (a) dev addr - * 0 is reserved by USB for default address; (b) Linux's USB stack - * uses always #1 for the root hub of the controller. So USB stack's - * port #1, which is wusb virtual-port #0 has address #2. - * * Devices connected under xHCI are not as simple. The host controller * supports virtualization, so the hardware assigns device addresses and * the HCD must setup data structures before issuing a set address @@ -2145,19 +2152,13 @@ static void choose_devnum(struct usb_device *udev) /* be safe when more hub events are proceed in parallel */ mutex_lock(&bus->devnum_next_mutex); - if (udev->wusb) { - devnum = udev->portnum + 1; - BUG_ON(test_bit(devnum, bus->devmap.devicemap)); - } else { - /* Try to allocate the next devnum beginning at - * bus->devnum_next. */ - devnum = find_next_zero_bit(bus->devmap.devicemap, 128, - bus->devnum_next); - if (devnum >= 128) - devnum = find_next_zero_bit(bus->devmap.devicemap, - 128, 1); - bus->devnum_next = (devnum >= 127 ? 1 : devnum + 1); - } + + /* Try to allocate the next devnum beginning at bus->devnum_next. */ + devnum = find_next_zero_bit(bus->devmap.devicemap, 128, + bus->devnum_next); + if (devnum >= 128) + devnum = find_next_zero_bit(bus->devmap.devicemap, 128, 1); + bus->devnum_next = (devnum >= 127 ? 1 : devnum + 1); if (devnum < 128) { set_bit(devnum, bus->devmap.devicemap); udev->devnum = devnum; @@ -2175,9 +2176,7 @@ static void release_devnum(struct usb_device *udev) static void update_devnum(struct usb_device *udev, int devnum) { - /* The address for a WUSB device is managed by wusbcore. */ - if (!udev->wusb) - udev->devnum = devnum; + udev->devnum = devnum; if (!udev->devaddr) udev->devaddr = (u8)devnum; } @@ -2670,15 +2669,6 @@ int usb_authorize_device(struct usb_device *usb_dev) goto error_autoresume; } - if (usb_dev->wusb) { - result = usb_get_device_descriptor(usb_dev, sizeof(usb_dev->descriptor)); - if (result < 0) { - dev_err(&usb_dev->dev, "can't re-read device descriptor for " - "authorization: %d\n", result); - goto error_device_descriptor; - } - } - usb_dev->authorized = 1; /* Choose and set the configuration. This registers the interfaces * with the driver core and lets interface drivers bind to them. @@ -2695,7 +2685,6 @@ int usb_authorize_device(struct usb_device *usb_dev) } dev_info(&usb_dev->dev, "authorized to connect\n"); -error_device_descriptor: usb_autosuspend_device(usb_dev); error_autoresume: out_authorized: @@ -2778,17 +2767,6 @@ out: return USB_SSP_GEN_UNKNOWN; } -/* Returns 1 if @hub is a WUSB root hub, 0 otherwise */ -static unsigned hub_is_wusb(struct usb_hub *hub) -{ - struct usb_hcd *hcd; - if (hub->hdev->parent != NULL) /* not a root hub? */ - return 0; - hcd = bus_to_hcd(hub->hdev->bus); - return hcd->wireless; -} - - #ifdef CONFIG_USB_FEW_INIT_RETRIES #define PORT_RESET_TRIES 2 #define SET_ADDRESS_TRIES 1 @@ -2941,9 +2919,7 @@ static int hub_port_wait_reset(struct usb_hub *hub, int port1, udev->tx_lanes = 1; udev->ssp_rate = USB_SSP_GEN_UNKNOWN; } - if (hub_is_wusb(hub)) - udev->speed = USB_SPEED_WIRELESS; - else if (udev->ssp_rate != USB_SSP_GEN_UNKNOWN) + if (udev->ssp_rate != USB_SSP_GEN_UNKNOWN) udev->speed = USB_SPEED_SUPER_PLUS; else if (hub_is_superspeed(hub->hdev)) udev->speed = USB_SPEED_SUPER; @@ -4718,6 +4694,67 @@ static int hub_enable_device(struct usb_device *udev) return hcd->driver->enable_device(hcd, udev); } +/* + * Get the bMaxPacketSize0 value during initialization by reading the + * device's device descriptor. Since we don't already know this value, + * the transfer is unsafe and it ignores I/O errors, only testing for + * reasonable received values. + * + * For "old scheme" initialization, size will be 8 so we read just the + * start of the device descriptor, which should work okay regardless of + * the actual bMaxPacketSize0 value. For "new scheme" initialization, + * size will be 64 (and buf will point to a sufficiently large buffer), + * which might not be kosher according to the USB spec but it's what + * Windows does and what many devices expect. + * + * Returns: bMaxPacketSize0 or a negative error code. + */ +static int get_bMaxPacketSize0(struct usb_device *udev, + struct usb_device_descriptor *buf, int size, bool first_time) +{ + int i, rc; + + /* + * Retry on all errors; some devices are flakey. + * 255 is for WUSB devices, we actually need to use + * 512 (WUSB1.0[4.8.1]). + */ + for (i = 0; i < GET_MAXPACKET0_TRIES; ++i) { + /* Start with invalid values in case the transfer fails */ + buf->bDescriptorType = buf->bMaxPacketSize0 = 0; + rc = usb_control_msg(udev, usb_rcvaddr0pipe(), + USB_REQ_GET_DESCRIPTOR, USB_DIR_IN, + USB_DT_DEVICE << 8, 0, + buf, size, + initial_descriptor_timeout); + switch (buf->bMaxPacketSize0) { + case 8: case 16: case 32: case 64: case 9: + if (buf->bDescriptorType == USB_DT_DEVICE) { + rc = buf->bMaxPacketSize0; + break; + } + fallthrough; + default: + if (rc >= 0) + rc = -EPROTO; + break; + } + + /* + * Some devices time out if they are powered on + * when already connected. They need a second + * reset, so return early. But only on the first + * attempt, lest we get into a time-out/reset loop. + */ + if (rc > 0 || (rc == -ETIMEDOUT && first_time && + udev->speed > USB_SPEED_FULL)) + break; + } + return rc; +} + +#define GET_DESCRIPTOR_BUFSIZE 64 + /* Reset device, (re)assign address, get device descriptor. * Device connection must be stable, no more debouncing needed. * Returns device in USB_STATE_ADDRESS, except on error. @@ -4727,10 +4764,17 @@ static int hub_enable_device(struct usb_device *udev) * the port lock. For a newly detected device that is not accessible * through any global pointers, it's not necessary to lock the device, * but it is still necessary to lock the port. + * + * For a newly detected device, @dev_descr must be NULL. The device + * descriptor retrieved from the device will then be stored in + * @udev->descriptor. For an already existing device, @dev_descr + * must be non-NULL. The device descriptor will be stored there, + * not in @udev->descriptor, because descriptors for registered + * devices are meant to be immutable. */ static int hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, - int retry_counter) + int retry_counter, struct usb_device_descriptor *dev_descr) { struct usb_device *hdev = hub->hdev; struct usb_hcd *hcd = bus_to_hcd(hdev->bus); @@ -4742,6 +4786,13 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, int devnum = udev->devnum; const char *driver_name; bool do_new_scheme; + const bool initial = !dev_descr; + int maxp0; + struct usb_device_descriptor *buf, *descr; + + buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO); + if (!buf) + return -ENOMEM; /* root hub ports have a slightly longer reset period * (from USB 2.0 spec, section 7.1.7.5) @@ -4774,38 +4825,34 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, } oldspeed = udev->speed; - /* USB 2.0 section 5.5.3 talks about ep0 maxpacket ... - * it's fixed size except for full speed devices. - * For Wireless USB devices, ep0 max packet is always 512 (tho - * reported as 0xff in the device descriptor). WUSB1.0[4.8.1]. - */ - switch (udev->speed) { - case USB_SPEED_SUPER_PLUS: - case USB_SPEED_SUPER: - case USB_SPEED_WIRELESS: /* fixed at 512 */ - udev->ep0.desc.wMaxPacketSize = cpu_to_le16(512); - break; - case USB_SPEED_HIGH: /* fixed at 64 */ - udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64); - break; - case USB_SPEED_FULL: /* 8, 16, 32, or 64 */ - /* to determine the ep0 maxpacket size, try to read - * the device descriptor to get bMaxPacketSize0 and - * then correct our initial guess. + if (initial) { + /* USB 2.0 section 5.5.3 talks about ep0 maxpacket ... + * it's fixed size except for full speed devices. */ - udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64); - break; - case USB_SPEED_LOW: /* fixed at 8 */ - udev->ep0.desc.wMaxPacketSize = cpu_to_le16(8); - break; - default: - goto fail; + switch (udev->speed) { + case USB_SPEED_SUPER_PLUS: + case USB_SPEED_SUPER: + udev->ep0.desc.wMaxPacketSize = cpu_to_le16(512); + break; + case USB_SPEED_HIGH: /* fixed at 64 */ + udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64); + break; + case USB_SPEED_FULL: /* 8, 16, 32, or 64 */ + /* to determine the ep0 maxpacket size, try to read + * the device descriptor to get bMaxPacketSize0 and + * then correct our initial guess. + */ + udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64); + break; + case USB_SPEED_LOW: /* fixed at 8 */ + udev->ep0.desc.wMaxPacketSize = cpu_to_le16(8); + break; + default: + goto fail; + } } - if (udev->speed == USB_SPEED_WIRELESS) - speed = "variable speed Wireless"; - else - speed = usb_speed_string(udev->speed); + speed = usb_speed_string(udev->speed); /* * The controller driver may be NULL if the controller device @@ -4822,22 +4869,24 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, if (udev->speed < USB_SPEED_SUPER) dev_info(&udev->dev, "%s %s USB device number %d using %s\n", - (udev->config) ? "reset" : "new", speed, + (initial ? "new" : "reset"), speed, devnum, driver_name); - /* Set up TT records, if needed */ - if (hdev->tt) { - udev->tt = hdev->tt; - udev->ttport = hdev->ttport; - } else if (udev->speed != USB_SPEED_HIGH - && hdev->speed == USB_SPEED_HIGH) { - if (!hub->tt.hub) { - dev_err(&udev->dev, "parent hub has no TT\n"); - retval = -EINVAL; - goto fail; + if (initial) { + /* Set up TT records, if needed */ + if (hdev->tt) { + udev->tt = hdev->tt; + udev->ttport = hdev->ttport; + } else if (udev->speed != USB_SPEED_HIGH + && hdev->speed == USB_SPEED_HIGH) { + if (!hub->tt.hub) { + dev_err(&udev->dev, "parent hub has no TT\n"); + retval = -EINVAL; + goto fail; + } + udev->tt = &hub->tt; + udev->ttport = port1; } - udev->tt = &hub->tt; - udev->ttport = port1; } /* Why interleave GET_DESCRIPTOR and SET_ADDRESS this way? @@ -4861,9 +4910,6 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, } if (do_new_scheme) { - struct usb_device_descriptor *buf; - int r = 0; - retval = hub_enable_device(udev); if (retval < 0) { dev_err(&udev->dev, @@ -4872,52 +4918,14 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, goto fail; } -#define GET_DESCRIPTOR_BUFSIZE 64 - buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO); - if (!buf) { - retval = -ENOMEM; - continue; - } - - /* Retry on all errors; some devices are flakey. - * 255 is for WUSB devices, we actually need to use - * 512 (WUSB1.0[4.8.1]). - */ - for (operations = 0; operations < GET_MAXPACKET0_TRIES; - ++operations) { - buf->bMaxPacketSize0 = 0; - r = usb_control_msg(udev, usb_rcvaddr0pipe(), - USB_REQ_GET_DESCRIPTOR, USB_DIR_IN, - USB_DT_DEVICE << 8, 0, - buf, GET_DESCRIPTOR_BUFSIZE, - initial_descriptor_timeout); - switch (buf->bMaxPacketSize0) { - case 8: case 16: case 32: case 64: case 255: - if (buf->bDescriptorType == - USB_DT_DEVICE) { - r = 0; - break; - } - fallthrough; - default: - if (r == 0) - r = -EPROTO; - break; - } - /* - * Some devices time out if they are powered on - * when already connected. They need a second - * reset. But only on the first attempt, - * lest we get into a time out/reset loop - */ - if (r == 0 || (r == -ETIMEDOUT && - retries == 0 && - udev->speed > USB_SPEED_FULL)) - break; + maxp0 = get_bMaxPacketSize0(udev, buf, + GET_DESCRIPTOR_BUFSIZE, retries == 0); + if (maxp0 > 0 && !initial && + maxp0 != udev->descriptor.bMaxPacketSize0) { + dev_err(&udev->dev, "device reset changed ep0 maxpacket size!\n"); + retval = -ENODEV; + goto fail; } - udev->descriptor.bMaxPacketSize0 = - buf->bMaxPacketSize0; - kfree(buf); retval = hub_port_reset(hub, port1, udev, delay, false); if (retval < 0) /* error or disconnect */ @@ -4928,71 +4936,68 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, retval = -ENODEV; goto fail; } - if (r) { - if (r != -ENODEV) + if (maxp0 < 0) { + if (maxp0 != -ENODEV) dev_err(&udev->dev, "device descriptor read/64, error %d\n", - r); - retval = -EMSGSIZE; + maxp0); + retval = maxp0; continue; } -#undef GET_DESCRIPTOR_BUFSIZE + } + + for (operations = 0; operations < SET_ADDRESS_TRIES; ++operations) { + retval = hub_set_address(udev, devnum); + if (retval >= 0) + break; + msleep(200); + } + if (retval < 0) { + if (retval != -ENODEV) + dev_err(&udev->dev, "device not accepting address %d, error %d\n", + devnum, retval); + goto fail; + } + if (udev->speed >= USB_SPEED_SUPER) { + devnum = udev->devnum; + dev_info(&udev->dev, + "%s SuperSpeed%s%s USB device number %d using %s\n", + (udev->config) ? "reset" : "new", + (udev->speed == USB_SPEED_SUPER_PLUS) ? + " Plus" : "", + (udev->ssp_rate == USB_SSP_GEN_2x2) ? + " Gen 2x2" : + (udev->ssp_rate == USB_SSP_GEN_2x1) ? + " Gen 2x1" : + (udev->ssp_rate == USB_SSP_GEN_1x2) ? + " Gen 1x2" : "", + devnum, driver_name); } /* - * If device is WUSB, we already assigned an - * unauthorized address in the Connect Ack sequence; - * authorization will assign the final address. + * cope with hardware quirkiness: + * - let SET_ADDRESS settle, some device hardware wants it + * - read ep0 maxpacket even for high and low speed, */ - if (udev->wusb == 0) { - for (operations = 0; operations < SET_ADDRESS_TRIES; ++operations) { - retval = hub_set_address(udev, devnum); - if (retval >= 0) - break; - msleep(200); - } - if (retval < 0) { - if (retval != -ENODEV) - dev_err(&udev->dev, "device not accepting address %d, error %d\n", - devnum, retval); - goto fail; - } - if (udev->speed >= USB_SPEED_SUPER) { - devnum = udev->devnum; - dev_info(&udev->dev, - "%s SuperSpeed%s%s USB device number %d using %s\n", - (udev->config) ? "reset" : "new", - (udev->speed == USB_SPEED_SUPER_PLUS) ? - " Plus" : "", - (udev->ssp_rate == USB_SSP_GEN_2x2) ? - " Gen 2x2" : - (udev->ssp_rate == USB_SSP_GEN_2x1) ? - " Gen 2x1" : - (udev->ssp_rate == USB_SSP_GEN_1x2) ? - " Gen 1x2" : "", - devnum, driver_name); - } + msleep(10); - /* cope with hardware quirkiness: - * - let SET_ADDRESS settle, some device hardware wants it - * - read ep0 maxpacket even for high and low speed, - */ - msleep(10); - if (do_new_scheme) - break; - } + if (do_new_scheme) + break; - retval = usb_get_device_descriptor(udev, 8); - if (retval < 8) { + maxp0 = get_bMaxPacketSize0(udev, buf, 8, retries == 0); + if (maxp0 < 0) { + retval = maxp0; if (retval != -ENODEV) dev_err(&udev->dev, "device descriptor read/8, error %d\n", retval); - if (retval >= 0) - retval = -EMSGSIZE; } else { u32 delay; - retval = 0; + if (!initial && maxp0 != udev->descriptor.bMaxPacketSize0) { + dev_err(&udev->dev, "device reset changed ep0 maxpacket size!\n"); + retval = -ENODEV; + goto fail; + } delay = udev->parent->hub_delay; udev->hub_delay = min_t(u32, delay, @@ -5011,54 +5016,67 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, goto fail; /* - * Some superspeed devices have finished the link training process - * and attached to a superspeed hub port, but the device descriptor - * got from those devices show they aren't superspeed devices. Warm - * reset the port attached by the devices can fix them. + * Check the ep0 maxpacket guess and correct it if necessary. + * maxp0 is the value stored in the device descriptor; + * i is the value it encodes (logarithmic for SuperSpeed or greater). */ - if ((udev->speed >= USB_SPEED_SUPER) && - (le16_to_cpu(udev->descriptor.bcdUSB) < 0x0300)) { - dev_err(&udev->dev, "got a wrong device descriptor, " - "warm reset device\n"); - hub_port_reset(hub, port1, udev, - HUB_BH_RESET_TIME, true); - retval = -EINVAL; - goto fail; - } - - if (udev->descriptor.bMaxPacketSize0 == 0xff || - udev->speed >= USB_SPEED_SUPER) - i = 512; - else - i = udev->descriptor.bMaxPacketSize0; - if (usb_endpoint_maxp(&udev->ep0.desc) != i) { - if (udev->speed == USB_SPEED_LOW || - !(i == 8 || i == 16 || i == 32 || i == 64)) { - dev_err(&udev->dev, "Invalid ep0 maxpacket: %d\n", i); - retval = -EMSGSIZE; - goto fail; - } + i = maxp0; + if (udev->speed >= USB_SPEED_SUPER) { + if (maxp0 <= 16) + i = 1 << maxp0; + else + i = 0; /* Invalid */ + } + if (usb_endpoint_maxp(&udev->ep0.desc) == i) { + ; /* Initial ep0 maxpacket guess is right */ + } else if ((udev->speed == USB_SPEED_FULL || + udev->speed == USB_SPEED_HIGH) && + (i == 8 || i == 16 || i == 32 || i == 64)) { + /* Initial guess is wrong; use the descriptor's value */ if (udev->speed == USB_SPEED_FULL) dev_dbg(&udev->dev, "ep0 maxpacket = %d\n", i); else dev_warn(&udev->dev, "Using ep0 maxpacket: %d\n", i); udev->ep0.desc.wMaxPacketSize = cpu_to_le16(i); usb_ep0_reinit(udev); + } else { + /* Initial guess is wrong and descriptor's value is invalid */ + dev_err(&udev->dev, "Invalid ep0 maxpacket: %d\n", maxp0); + retval = -EMSGSIZE; + goto fail; } - retval = usb_get_device_descriptor(udev, USB_DT_DEVICE_SIZE); - if (retval < (signed)sizeof(udev->descriptor)) { + descr = usb_get_device_descriptor(udev); + if (IS_ERR(descr)) { + retval = PTR_ERR(descr); if (retval != -ENODEV) dev_err(&udev->dev, "device descriptor read/all, error %d\n", retval); - if (retval >= 0) - retval = -ENOMSG; + goto fail; + } + if (initial) + udev->descriptor = *descr; + else + *dev_descr = *descr; + kfree(descr); + + /* + * Some superspeed devices have finished the link training process + * and attached to a superspeed hub port, but the device descriptor + * got from those devices show they aren't superspeed devices. Warm + * reset the port attached by the devices can fix them. + */ + if ((udev->speed >= USB_SPEED_SUPER) && + (le16_to_cpu(udev->descriptor.bcdUSB) < 0x0300)) { + dev_err(&udev->dev, "got a wrong device descriptor, warm reset device\n"); + hub_port_reset(hub, port1, udev, HUB_BH_RESET_TIME, true); + retval = -EINVAL; goto fail; } usb_detect_quirks(udev); - if (udev->wusb == 0 && le16_to_cpu(udev->descriptor.bcdUSB) >= 0x0201) { + if (le16_to_cpu(udev->descriptor.bcdUSB) >= 0x0201) { retval = usb_get_bos_descriptor(udev); if (!retval) { udev->lpm_capable = usb_device_supports_lpm(udev); @@ -5078,6 +5096,7 @@ fail: hub_port_disable(hub, port1, 0); update_devnum(udev, devnum); /* for disconnect processing */ } + kfree(buf); return retval; } @@ -5158,7 +5177,7 @@ hub_power_remaining(struct usb_hub *hub) static int descriptors_changed(struct usb_device *udev, - struct usb_device_descriptor *old_device_descriptor, + struct usb_device_descriptor *new_device_descriptor, struct usb_host_bos *old_bos) { int changed = 0; @@ -5169,8 +5188,8 @@ static int descriptors_changed(struct usb_device *udev, int length; char *buf; - if (memcmp(&udev->descriptor, old_device_descriptor, - sizeof(*old_device_descriptor)) != 0) + if (memcmp(&udev->descriptor, new_device_descriptor, + sizeof(*new_device_descriptor)) != 0) return 1; if ((old_bos && !udev->bos) || (!old_bos && udev->bos)) @@ -5333,7 +5352,6 @@ static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus, usb_set_device_state(udev, USB_STATE_POWERED); udev->bus_mA = hub->mA_per_port; udev->level = hdev->level + 1; - udev->wusb = hub_is_wusb(hub); /* Devices connected to SuperSpeed hubs are USB 3.0 or later */ if (hub_is_superspeed(hub->hdev)) @@ -5348,7 +5366,7 @@ static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus, } /* reset (non-USB 3.0 devices) and get descriptor */ - status = hub_port_init(hub, udev, port1, i); + status = hub_port_init(hub, udev, port1, i, NULL); if (status < 0) goto loop; @@ -5495,9 +5513,8 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, { struct usb_port *port_dev = hub->ports[port1 - 1]; struct usb_device *udev = port_dev->child; - struct usb_device_descriptor descriptor; + struct usb_device_descriptor *descr; int status = -ENODEV; - int retval; dev_dbg(&port_dev->dev, "status %04x, change %04x, %s\n", portstatus, portchange, portspeed(hub, portstatus)); @@ -5524,23 +5541,20 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, * changed device descriptors before resuscitating the * device. */ - descriptor = udev->descriptor; - retval = usb_get_device_descriptor(udev, - sizeof(udev->descriptor)); - if (retval < 0) { + descr = usb_get_device_descriptor(udev); + if (IS_ERR(descr)) { dev_dbg(&udev->dev, - "can't read device descriptor %d\n", - retval); + "can't read device descriptor %ld\n", + PTR_ERR(descr)); } else { - if (descriptors_changed(udev, &descriptor, + if (descriptors_changed(udev, descr, udev->bos)) { dev_dbg(&udev->dev, "device descriptor has changed\n"); - /* for disconnect() calls */ - udev->descriptor = descriptor; } else { status = 0; /* Nothing to do */ } + kfree(descr); } #ifdef CONFIG_PM } else if (udev->state == USB_STATE_SUSPENDED && @@ -5982,7 +5996,7 @@ static int usb_reset_and_verify_device(struct usb_device *udev) struct usb_device *parent_hdev = udev->parent; struct usb_hub *parent_hub; struct usb_hcd *hcd = bus_to_hcd(udev->bus); - struct usb_device_descriptor descriptor = udev->descriptor; + struct usb_device_descriptor descriptor; struct usb_host_bos *bos; int i, j, ret = 0; int port1 = udev->portnum; @@ -6018,7 +6032,7 @@ static int usb_reset_and_verify_device(struct usb_device *udev) /* ep0 maxpacket size may change; let the HCD know about it. * Other endpoints will be handled by re-enumeration. */ usb_ep0_reinit(udev); - ret = hub_port_init(parent_hub, udev, port1, i); + ret = hub_port_init(parent_hub, udev, port1, i, &descriptor); if (ret >= 0 || ret == -ENOTCONN || ret == -ENODEV) break; } @@ -6030,7 +6044,6 @@ static int usb_reset_and_verify_device(struct usb_device *udev) /* Device might have changed firmware (DFU or similar) */ if (descriptors_changed(udev, &descriptor, bos)) { dev_info(&udev->dev, "device firmware changed\n"); - udev->descriptor = descriptor; /* for disconnect() calls */ goto re_enumerate; } |