From 4de2730a1d2742aea67f24d1041bdc5e0bad37e3 Mon Sep 17 00:00:00 2001 From: Patrick Boettcher Date: Mon, 17 Apr 2006 13:22:15 -0300 Subject: V4L/DVB (4451): MT2060: IF1 Offset from EEPROM, several updates - AGC gain set to 3 - The tuning sequence has been changed to match the DibCom driver ( from I2C spy captures ) - For LITE-ON adapters : The IF1 frequency is now tuned according to the calibration values stored in EEPROM. Signed-off-by: Patrick Boettcher Signed-off-by: Olivier DANET Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/dvb-usb/dibusb-common.c | 23 ++- drivers/media/dvb/frontends/mt2060.c | 312 ++++++++++++++++++++++++++++++ drivers/media/dvb/frontends/mt2060.h | 44 +++++ drivers/media/dvb/frontends/mt2060_priv.h | 95 +++++++++ 4 files changed, 472 insertions(+), 2 deletions(-) create mode 100644 drivers/media/dvb/frontends/mt2060.c create mode 100644 drivers/media/dvb/frontends/mt2060.h create mode 100644 drivers/media/dvb/frontends/mt2060_priv.h diff --git a/drivers/media/dvb/dvb-usb/dibusb-common.c b/drivers/media/dvb/dvb-usb/dibusb-common.c index e079ba95d3841..88062b219b914 100644 --- a/drivers/media/dvb/dvb-usb/dibusb-common.c +++ b/drivers/media/dvb/dvb-usb/dibusb-common.c @@ -234,12 +234,31 @@ EXPORT_SYMBOL(dibusb_dib3000mc_frontend_attach); int dibusb_dib3000mc_tuner_attach (struct dvb_usb_device *d) { int ret; + u8 a,b; + u16 if1=1220; if (d->tuner_pass_ctrl) { struct dibusb_state *st = d->priv; d->tuner_pass_ctrl(d->fe, 1, stk3000p_mt2060_config.i2c_address); - /* check for mt2060 */ - if ((ret = mt2060_attach(&st->mt2060,&stk3000p_mt2060_config, &d->i2c_adap)) != 0) { + // First IF calibration for Liteon Sticks + if (d->udev->descriptor.idVendor == USB_VID_LITEON && + d->udev->descriptor.idProduct == USB_PID_LITEON_DVB_T_WARM) { + dibusb_read_eeprom_byte(d,0x7E,&a); + dibusb_read_eeprom_byte(d,0x7F,&b); + if (a == 0xFF && b == 0xFF) { + if1 = 1220; + } else + if (a == 0x00) { + if1 = 1220+b; + } else + if (a == 0x80) { + if1 = 1220-b; + } else { + warn("LITE-ON DVB-T Tuner : Strange IF1 calibration :%2X %2X\n",(int)a,(int)b); + if1 = 1220; + } + } + if ((ret = mt2060_attach(&st->mt2060,&stk3000p_mt2060_config, &d->i2c_adap,if1)) != 0) { /* not found - use panasonic pll parameters */ d->pll_addr = 0x60; d->pll_desc = &dvb_pll_env57h1xd5; diff --git a/drivers/media/dvb/frontends/mt2060.c b/drivers/media/dvb/frontends/mt2060.c new file mode 100644 index 0000000000000..aa92c1c51e6d1 --- /dev/null +++ b/drivers/media/dvb/frontends/mt2060.c @@ -0,0 +1,312 @@ +/* + * Driver for Microtune MT2060 "Single chip dual conversion broadband tuner" + * + * Copyright (c) 2006 Olivier DANET + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.= + */ + +/* See mt2060_priv.h for details */ + +/* In that file, frequencies are expressed in kiloHertz to avoid 32 bits overflows */ + +#include +#include +#include +#include +#include "mt2060.h" +#include "mt2060_priv.h" + +static int debug=0; +module_param(debug, int, 0644); +MODULE_PARM_DESC(debug, "Turn on/off debugging (default:off)."); + +#define dprintk(args...) do { if (debug) printk(KERN_DEBUG "MT2060: " args); printk("\n"); } while (0) + +// Reads a single register +static int mt2060_readreg(struct mt2060_state *state, u8 reg, u8 *val) +{ + struct i2c_msg msg[2] = { + { .addr = state->config->i2c_address, .flags = 0, .buf = ®, .len = 1 }, + { .addr = state->config->i2c_address, .flags = I2C_M_RD, .buf = val, .len = 1 }, + }; + + if (i2c_transfer(state->i2c, msg, 2) != 2) { + printk(KERN_WARNING "mt2060 I2C read failed\n"); + return -EREMOTEIO; + } + return 0; +} + +// Writes a single register +static int mt2060_writereg(struct mt2060_state *state, u8 reg, u8 val) +{ + u8 buf[2]; + struct i2c_msg msg = { + .addr = state->config->i2c_address, .flags = 0, .buf = buf, .len = 2 + }; + buf[0]=reg; + buf[1]=val; + + if (i2c_transfer(state->i2c, &msg, 1) != 1) { + printk(KERN_WARNING "mt2060 I2C write failed\n"); + return -EREMOTEIO; + } + return 0; +} + +// Writes a set of consecutive registers +static int mt2060_writeregs(struct mt2060_state *state,u8 *buf, u8 len) +{ + struct i2c_msg msg = { + .addr = state->config->i2c_address, .flags = 0, .buf = buf, .len = len + }; + if (i2c_transfer(state->i2c, &msg, 1) != 1) { + printk(KERN_WARNING "mt2060 I2C write failed (len=%i)\n",(int)len); + return -EREMOTEIO; + } + return 0; +} + +// Initialisation sequences +// LNABAND=3, NUM1=0x3C, DIV1=0x74, NUM2=0x1080, DIV2=0x49 +static u8 mt2060_config1[] = { + REG_LO1C1, + 0x3F, 0x74, 0x00, 0x08, 0x93 +}; + +// FMCG=2, GP2=0, GP1=0 +static u8 mt2060_config2[] = { + REG_MISC_CTRL, + 0x20, 0x1E, 0x30, 0xff, 0x80, 0xff, 0x00, 0x2c, 0x42 +}; + +// VGAG=3, V1CSE=1 +static u8 mt2060_config3[] = { + REG_VGAG, + 0x33 +}; + +int mt2060_init(struct mt2060_state *state) +{ + if (mt2060_writeregs(state,mt2060_config1,sizeof(mt2060_config1))) + return -EREMOTEIO; + if (mt2060_writeregs(state,mt2060_config3,sizeof(mt2060_config3))) + return -EREMOTEIO; + return 0; +} +EXPORT_SYMBOL(mt2060_init); + +#ifdef MT2060_SPURCHECK +/* The function below calculates the frequency offset between the output frequency if2 + and the closer cross modulation subcarrier between lo1 and lo2 up to the tenth harmonic */ +static int mt2060_spurcalc(u32 lo1,u32 lo2,u32 if2) +{ + int I,J; + int dia,diamin,diff; + diamin=1000000; + for (I = 1; I < 10; I++) { + J = ((2*I*lo1)/lo2+1)/2; + diff = I*(int)lo1-J*(int)lo2; + if (diff < 0) diff=-diff; + dia = (diff-(int)if2); + if (dia < 0) dia=-dia; + if (diamin > dia) diamin=dia; + } + return diamin; +} + +#define BANDWIDTH 4000 // kHz + +/* Calculates the frequency offset to add to avoid spurs. Returns 0 if no offset is needed */ +static int mt2060_spurcheck(u32 lo1,u32 lo2,u32 if2) +{ + u32 Spur,Sp1,Sp2; + int I,J; + I=0; + J=1000; + + Spur=mt2060_spurcalc(lo1,lo2,if2); + if (Spur < BANDWIDTH) { + /* Potential spurs detected */ + dprintk("Spurs before : f_lo1: %d f_lo2: %d (kHz)", + (int)lo1,(int)lo2); + I=1000; + Sp1 = mt2060_spurcalc(lo1+I,lo2+I,if2); + Sp2 = mt2060_spurcalc(lo1-I,lo2-I,if2); + + if (Sp1 < Sp2) { + J=-J; I=-I; Spur=Sp2; + } else + Spur=Sp1; + + while (Spur < BANDWIDTH) { + I += J; + Spur = mt2060_spurcalc(lo1+I,lo2+I,if2); + } + dprintk("Spurs after : f_lo1: %d f_lo2: %d (kHz)", + (int)(lo1+I),(int)(lo2+I)); + } + return I; +} +#endif + +#define IF2 36150 // IF2 frequency = 36.150 MHz +#define FREF 16000 // Quartz oscillator 16 MHz + +int mt2060_set(struct mt2060_state *state, struct dvb_frontend_parameters *fep) +{ + int ret=0; + int i=0; + u32 freq; + u8 lnaband; + u32 f_lo1,f_lo2; + u32 div1,num1,div2,num2; + u8 b[8]; + u32 if1; + + if1 = state->if1_freq; + b[0] = REG_LO1B1; + b[1] = 0xFF; + mt2060_writeregs(state,b,2); + + freq = fep->frequency / 1000; // Hz -> kHz + + f_lo1 = freq + if1 * 1000; + f_lo1 = (f_lo1/250)*250; + f_lo2 = f_lo1 - freq - IF2; + f_lo2 = (f_lo2/50)*50; + +#ifdef MT2060_SPURCHECK + // LO-related spurs detection and correction + num1 = mt2060_spurcheck(f_lo1,f_lo2,IF2); + f_lo1 += num1; + f_lo2 += num1; +#endif + //Frequency LO1 = 16MHz * (DIV1 + NUM1/64 ) + div1 = f_lo1 / FREF; + num1 = (64 * (f_lo1 % FREF) )/FREF; + + // Frequency LO2 = 16MHz * (DIV2 + NUM2/8192 ) + div2 = f_lo2 / FREF; + num2 = (16384 * (f_lo2 % FREF) /FREF +1)/2; + + if (freq <= 95000) lnaband = 0xB0; else + if (freq <= 180000) lnaband = 0xA0; else + if (freq <= 260000) lnaband = 0x90; else + if (freq <= 335000) lnaband = 0x80; else + if (freq <= 425000) lnaband = 0x70; else + if (freq <= 480000) lnaband = 0x60; else + if (freq <= 570000) lnaband = 0x50; else + if (freq <= 645000) lnaband = 0x40; else + if (freq <= 730000) lnaband = 0x30; else + if (freq <= 810000) lnaband = 0x20; else lnaband = 0x10; + + b[0] = REG_LO1C1; + b[1] = lnaband | ((num1 >>2) & 0x0F); + b[2] = div1; + b[3] = (num2 & 0x0F) | ((num1 & 3) << 4); + b[4] = num2 >> 4; + b[5] = ((num2 >>12) & 1) | (div2 << 1); + + dprintk("IF1: %dMHz",(int)if1); + dprintk("PLL freq: %d f_lo1: %d f_lo2: %d (kHz)",(int)freq,(int)f_lo1,(int)f_lo2); + dprintk("PLL div1: %d num1: %d div2: %d num2: %d",(int)div1,(int)num1,(int)div2,(int)num2); + dprintk("PLL [1..5]: %2x %2x %2x %2x %2x",(int)b[1],(int)b[2],(int)b[3],(int)b[4],(int)b[5]); + + mt2060_writeregs(state,b,6); + + //Waits for pll lock or timeout + i=0; + do { + mt2060_readreg(state,REG_LO_STATUS,b); + if ((b[0] & 0x88)==0x88) break; + msleep(4); + i++; + } while (i<10); + + return ret; +} +EXPORT_SYMBOL(mt2060_set); + +/* from usbsnoop.log */ +static void mt2060_calibrate(struct mt2060_state *state) +{ + u8 b = 0; + int i = 0; + + if (mt2060_writeregs(state,mt2060_config1,sizeof(mt2060_config1))) + return; + if (mt2060_writeregs(state,mt2060_config2,sizeof(mt2060_config2))) + return; + + do { + b |= (1 << 6); // FM1SS; + mt2060_writereg(state, REG_LO2C1,b); + msleep(20); + + if (i == 0) { + b |= (1 << 7); // FM1CA; + mt2060_writereg(state, REG_LO2C1,b); + b &= ~(1 << 7); // FM1CA; + msleep(20); + } + + b &= ~(1 << 6); // FM1SS + mt2060_writereg(state, REG_LO2C1,b); + + msleep(20); + i++; + } while (i < 9); + + i = 0; + while (i++ < 10 && mt2060_readreg(state, REG_MISC_STAT, &b) == 0 && (b & (1 << 6)) == 0) + msleep(20); + + if (i < 10) { + mt2060_readreg(state, REG_FM_FREQ, &state->fmfreq); // now find out, what is fmreq used for :) + dprintk("calibration was successful: %d",state->fmfreq); + } else + dprintk("FMCAL timed out"); +} + +/* This functions tries to identify a MT2060 tuner by reading the PART/REV register. This is hasty. */ +int mt2060_attach(struct mt2060_state *state, struct mt2060_config *config, struct i2c_adapter *i2c,u16 if1) +{ + u8 id = 0; + memset(state,0,sizeof(struct mt2060_state)); + + state->config = config; + state->i2c = i2c; + state->if1_freq = if1; + + if (mt2060_readreg(state,REG_PART_REV,&id) != 0) + return -ENODEV; + + if (id != PART_REV) + return -ENODEV; + + printk(KERN_INFO "MT2060: successfully identified\n"); + + mt2060_calibrate(state); + + return 0; +} +EXPORT_SYMBOL(mt2060_attach); + +MODULE_AUTHOR("Olivier DANET"); +MODULE_DESCRIPTION("Microtune MT2060 silicon tuner driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/media/dvb/frontends/mt2060.h b/drivers/media/dvb/frontends/mt2060.h new file mode 100644 index 0000000000000..d5dae102f96ff --- /dev/null +++ b/drivers/media/dvb/frontends/mt2060.h @@ -0,0 +1,44 @@ +/* + * Driver for Microtune MT2060 "Single chip dual conversion broadband tuner" + * + * Copyright (c) 2006 Olivier DANET + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.= + */ + +#ifndef MT2060_H +#define MT2060_H + +#include +#include + +struct mt2060_config { + u8 i2c_address; + /* Shall we add settings for the discrete outputs ? */ +}; + +struct mt2060_state { + struct mt2060_config *config; + struct i2c_adapter *i2c; + u16 if1_freq; + u8 fmfreq; +}; + +extern int mt2060_init(struct mt2060_state *state); +extern int mt2060_set(struct mt2060_state *state, struct dvb_frontend_parameters *fep); +extern int mt2060_attach(struct mt2060_state *state, struct mt2060_config *config, struct i2c_adapter *i2c,u16 if1); + +#endif diff --git a/drivers/media/dvb/frontends/mt2060_priv.h b/drivers/media/dvb/frontends/mt2060_priv.h new file mode 100644 index 0000000000000..47e691e44b7b4 --- /dev/null +++ b/drivers/media/dvb/frontends/mt2060_priv.h @@ -0,0 +1,95 @@ +/* + * Driver for Microtune MT2060 "Single chip dual conversion broadband tuner" + * + * Copyright (c) 2006 Olivier DANET + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.= + */ + +#ifndef MT2060_PRIV_H +#define MT2060_PRIV_H + +// Uncomment the #define below to enable spurs checking. The results where quite unconvincing. +// #define MT2060_SPURCHECK + +/* This driver is based on the information available in the datasheet of the + "Comtech SDVBT-3K6M" tuner ( K1000737843.pdf ) which features the MT2060 register map : + + I2C Address : 0x60 + + Reg.No | B7 | B6 | B5 | B4 | B3 | B2 | B1 | B0 | ( defaults ) + -------------------------------------------------------------------------------- + 00 | [ PART ] | [ REV ] | R = 0x63 + 01 | [ LNABAND ] | [ NUM1(5:2) ] | RW = 0x3F + 02 | [ DIV1 ] | RW = 0x74 + 03 | FM1CA | FM1SS | [ NUM1(1:0) ] | [ NUM2(3:0) ] | RW = 0x00 + 04 | NUM2(11:4) ] | RW = 0x08 + 05 | [ DIV2 ] |NUM2(12)| RW = 0x93 + 06 | L1LK | [ TAD1 ] | L2LK | [ TAD2 ] | R + 07 | [ FMF ] | R + 08 | ? | FMCAL | ? | ? | ? | ? | ? | TEMP | R + 09 | 0 | 0 | [ FMGC ] | 0 | GP02 | GP01 | 0 | RW = 0x20 + 0A | ?? + 0B | 0 | 0 | 1 | 1 | 0 | 0 | [ VGAG ] | RW = 0x30 + 0C | V1CSE | 1 | 1 | 1 | 1 | 1 | 1 | 1 | RW = 0xFF + 0D | 1 | 0 | [ V1CS ] | RW = 0xB0 + 0E | ?? + 0F | ?? + 10 | ?? + 11 | [ LOTO ] | 0 | 0 | 1 | 0 | RW = 0x42 + + PART : Part code : 6 for MT2060 + REV : Revision code : 3 for current revision + LNABAND : Input frequency range : ( See code for details ) + NUM1 / DIV1 / NUM2 / DIV2 : Frequencies programming ( See code for details ) + FM1CA : Calibration Start Bit + FM1SS : Calibration Single Step bit + L1LK : LO1 Lock Detect + TAD1 : Tune Line ADC ( ? ) + L2LK : LO2 Lock Detect + TAD2 : Tune Line ADC ( ? ) + FMF : Estimated first IF Center frequency Offset ( ? ) + FM1CAL : Calibration done bit + TEMP : On chip temperature sensor + FMCG : Mixer 1 Cap Gain ( ? ) + GP01 / GP02 : Programmable digital outputs. Unconnected pins ? + V1CSE : LO1 VCO Automatic Capacitor Select Enable ( ? ) + V1CS : LO1 Capacitor Selection Value ( ? ) + LOTO : LO Timeout ( ? ) + VGAG : Tuner Output gain +*/ + +#define I2C_ADDRESS 0x60 + +#define REG_PART_REV 0 +#define REG_LO1C1 1 +#define REG_LO1C2 2 +#define REG_LO2C1 3 +#define REG_LO2C2 4 +#define REG_LO2C3 5 +#define REG_LO_STATUS 6 +#define REG_FM_FREQ 7 +#define REG_MISC_STAT 8 +#define REG_MISC_CTRL 9 +#define REG_RESERVED_A 0x0A +#define REG_VGAG 0x0B +#define REG_LO1B1 0x0C +#define REG_LO1B2 0x0D +#define REG_LOTO 0x11 + +#define PART_REV 0x63 // The current driver works only with PART=6 and REV=3 chips + +#endif -- cgit 1.2.3-korg