diff options
324 files changed, 5450 insertions, 1112 deletions
diff --git a/Documentation/powerpc/eeh-pci-error-recovery.txt b/Documentation/powerpc/eeh-pci-error-recovery.txt index 67a11a36270ca0..3764dd4b12cbac 100644 --- a/Documentation/powerpc/eeh-pci-error-recovery.txt +++ b/Documentation/powerpc/eeh-pci-error-recovery.txt @@ -121,7 +121,7 @@ accomplished. EEH must be enabled in the PHB's very early during the boot process, and if a PCI slot is hot-plugged. The former is performed by -eeh_init() in arch/ppc64/kernel/eeh.c, and the later by +eeh_init() in arch/powerpc/platforms/pseries/eeh.c, and the later by drivers/pci/hotplug/pSeries_pci.c calling in to the eeh.c code. EEH must be enabled before a PCI scan of the device can proceed. Current Power5 hardware will not work unless EEH is enabled; @@ -133,7 +133,7 @@ error. Given an arbitrary address, the routine pci_get_device_by_addr() will find the pci device associated with that address (if any). -The default include/asm-ppc64/io.h macros readb(), inb(), insb(), +The default include/asm-powerpc/io.h macros readb(), inb(), insb(), etc. include a check to see if the i/o read returned all-0xff's. If so, these make a call to eeh_dn_check_failure(), which in turn asks the firmware if the all-ff's value is the sign of a true EEH @@ -143,11 +143,12 @@ seen in /proc/ppc64/eeh (subject to change). Normally, almost all of these occur during boot, when the PCI bus is scanned, where a large number of 0xff reads are part of the bus scan procedure. -If a frozen slot is detected, code in arch/ppc64/kernel/eeh.c will -print a stack trace to syslog (/var/log/messages). This stack trace -has proven to be very useful to device-driver authors for finding -out at what point the EEH error was detected, as the error itself -usually occurs slightly beforehand. +If a frozen slot is detected, code in +arch/powerpc/platforms/pseries/eeh.c will print a stack trace to +syslog (/var/log/messages). This stack trace has proven to be very +useful to device-driver authors for finding out at what point the EEH +error was detected, as the error itself usually occurs slightly +beforehand. Next, it uses the Linux kernel notifier chain/work queue mechanism to allow any interested parties to find out about the failure. Device diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig index 80d114a3a837d0..fb0dcb994b84a6 100644 --- a/arch/powerpc/Kconfig +++ b/arch/powerpc/Kconfig @@ -127,6 +127,12 @@ config PPC_83xx select 83xx select PPC_FPU +config PPC_85xx + bool "Freescale 85xx" + select E500 + select FSL_SOC + select 85xx + config 40x bool "AMCC 40x" @@ -139,8 +145,6 @@ config 8xx config E200 bool "Freescale e200" -config E500 - bool "Freescale e500" endchoice config POWER4_ONLY @@ -168,6 +172,13 @@ config 6xx config 83xx bool +# this is temp to handle compat with arch=ppc +config 85xx + bool + +config E500 + bool + config PPC_FPU bool default y if PPC64 @@ -217,6 +228,7 @@ config ALTIVEC config SPE bool "SPE Support" depends on E200 || E500 + default y ---help--- This option enables kernel support for the Signal Processing Extensions (SPE) to the PowerPC processor. The kernel currently @@ -734,13 +746,12 @@ config GENERIC_ISA_DMA config PPC_I8259 bool - default y if 85xx default n config PPC_INDIRECT_PCI bool depends on PCI - default y if 40x || 44x || 85xx + default y if 40x || 44x default n config EISA @@ -757,8 +768,8 @@ config MCA bool config PCI - bool "PCI support" if 40x || CPM2 || PPC_83xx || 85xx || PPC_MPC52xx || (EMBEDDED && PPC_ISERIES) - default y if !40x && !CPM2 && !8xx && !APUS && !PPC_83xx && !85xx + bool "PCI support" if 40x || CPM2 || PPC_83xx || PPC_85xx || PPC_MPC52xx || (EMBEDDED && PPC_ISERIES) + default y if !40x && !CPM2 && !8xx && !APUS && !PPC_83xx && !PPC_85xx default PCI_PERMEDIA if !4xx && !CPM2 && !8xx && APUS default PCI_QSPAN if !4xx && !CPM2 && 8xx help diff --git a/arch/powerpc/Makefile b/arch/powerpc/Makefile index 5500ab55d04284..a3fc7a23158fad 100644 --- a/arch/powerpc/Makefile +++ b/arch/powerpc/Makefile @@ -148,7 +148,7 @@ all: $(KBUILD_IMAGE) CPPFLAGS_vmlinux.lds := -Upowerpc -BOOT_TARGETS = zImage zImage.initrd znetboot znetboot.initrd vmlinux.sm uImage +BOOT_TARGETS = zImage zImage.initrd znetboot znetboot.initrd vmlinux.sm uImage vmlinux.bin .PHONY: $(BOOT_TARGETS) diff --git a/arch/powerpc/boot/install.sh b/arch/powerpc/boot/install.sh index eacce9590816db..b002bfd56786bd 100644 --- a/arch/powerpc/boot/install.sh +++ b/arch/powerpc/boot/install.sh @@ -1,7 +1,5 @@ #!/bin/sh # -# arch/ppc64/boot/install.sh -# # This file is subject to the terms and conditions of the GNU General Public # License. See the file "COPYING" in the main directory of this archive # for more details. diff --git a/arch/powerpc/boot/main.c b/arch/powerpc/boot/main.c index 55ec5986725079..816446f0e497a6 100644 --- a/arch/powerpc/boot/main.c +++ b/arch/powerpc/boot/main.c @@ -152,7 +152,7 @@ static int is_elf64(void *hdr) elf64ph = (Elf64_Phdr *)((unsigned long)elf64 + (unsigned long)elf64->e_phoff); for (i = 0; i < (unsigned int)elf64->e_phnum; i++, elf64ph++) - if (elf64ph->p_type == PT_LOAD && elf64ph->p_offset != 0) + if (elf64ph->p_type == PT_LOAD) break; if (i >= (unsigned int)elf64->e_phnum) return 0; @@ -193,7 +193,7 @@ static int is_elf32(void *hdr) elf32 = (Elf32_Ehdr *)elfheader; elf32ph = (Elf32_Phdr *) ((unsigned long)elf32 + elf32->e_phoff); for (i = 0; i < elf32->e_phnum; i++, elf32ph++) - if (elf32ph->p_type == PT_LOAD && elf32ph->p_offset != 0) + if (elf32ph->p_type == PT_LOAD) break; if (i >= elf32->e_phnum) return 0; diff --git a/arch/powerpc/configs/mpc8540_ads_defconfig b/arch/powerpc/configs/mpc8540_ads_defconfig new file mode 100644 index 00000000000000..2a8290ee15c643 --- /dev/null +++ b/arch/powerpc/configs/mpc8540_ads_defconfig @@ -0,0 +1,721 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: +# Sat Jan 14 15:57:54 2006 +# +# CONFIG_PPC64 is not set +CONFIG_PPC32=y +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_PPC_UDBG_16550=y +# CONFIG_GENERIC_TBSYNC is not set + +# +# Processor support +# +# CONFIG_CLASSIC32 is not set +# CONFIG_PPC_52xx is not set +# CONFIG_PPC_82xx is not set +# CONFIG_PPC_83xx is not set +CONFIG_PPC_85xx=y +# CONFIG_40x is not set +# CONFIG_44x is not set +# CONFIG_8xx is not set +# CONFIG_E200 is not set +CONFIG_85xx=y +CONFIG_E500=y +CONFIG_BOOKE=y +CONFIG_FSL_BOOKE=y +# CONFIG_PHYS_64BIT is not set +CONFIG_SPE=y + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_CLEAN_COMPILE=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_EMBEDDED=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_CC_ALIGN_FUNCTIONS=0 +CONFIG_CC_ALIGN_LABELS=0 +CONFIG_CC_ALIGN_LOOPS=0 +CONFIG_CC_ALIGN_JUMPS=0 +CONFIG_SLAB=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set + +# +# Loadable module support +# +# CONFIG_MODULES is not set + +# +# Block layer +# +# CONFIG_LBD is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_MPIC=y +# CONFIG_WANT_EARLY_SERIAL is not set + +# +# Platform support +# +CONFIG_MPC8540_ADS=y +CONFIG_MPC8540=y +CONFIG_PPC_INDIRECT_PCI_BE=y + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +CONFIG_BINFMT_MISC=y +CONFIG_MATH_EMULATION=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_PROC_DEVICETREE=y +# CONFIG_CMDLINE_BOOL is not set +# CONFIG_PM is not set +# CONFIG_SOFTWARE_SUSPEND is not set +# CONFIG_SECCOMP is not set +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +# CONFIG_PPC_I8259 is not set +CONFIG_PPC_INDIRECT_PCI=y +CONFIG_FSL_SOC=y +# CONFIG_PCI is not set +# CONFIG_PCI_DOMAINS is not set + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# PCI Hotplug Support +# + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_HIGHMEM_START=0xfe000000 +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_TASK_SIZE=0x80000000 +CONFIG_BOOT_LOAD=0x00800000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +# CONFIG_MTD is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=32768 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Macintosh device drivers +# +# CONFIG_WINDFARM is not set + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# PHY device support +# +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y + +# +# Ethernet (1000 Mbit) +# +CONFIG_GIANFAR=y +CONFIG_GFAR_NAPI=y + +# +# Ethernet (10000 Mbit) +# + +# +# Token Ring devices +# + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +# CONFIG_WATCHDOG is not set +# CONFIG_NVRAM is not set +CONFIG_GEN_RTC=y +# CONFIG_GEN_RTC_X is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# Ftape, the floppy tape device driver +# +# CONFIG_AGP is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set + +# +# I2C support +# +# CONFIG_I2C is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Misc devices +# + +# +# Multimedia Capabilities Port drivers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +# CONFIG_USB_ARCH_HAS_HCD is not set +# CONFIG_USB_ARCH_HAS_OHCI is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# InfiniBand support +# + +# +# SN Devices +# + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_RELAYFS_FS is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +# CONFIG_NFS_V3 is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +# CONFIG_MSDOS_PARTITION is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_EFI_PARTITION is not set + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set + +# +# Instrumentation Support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +# CONFIG_MAGIC_SYSRQ is not set +CONFIG_DEBUG_KERNEL=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_DEBUGGER is not set +# CONFIG_BDI_SWITCH is not set +# CONFIG_BOOTX_TEXT is not set +# CONFIG_PPC_EARLY_DEBUG_LPAR is not set +# CONFIG_PPC_EARLY_DEBUG_G5 is not set +# CONFIG_PPC_EARLY_DEBUG_RTAS is not set +# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set +# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Hardware crypto devices +# diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c index 10696456a4c616..3191be7135fee8 100644 --- a/arch/powerpc/kernel/cputable.c +++ b/arch/powerpc/kernel/cputable.c @@ -891,7 +891,7 @@ struct cpu_spec cpu_specs[] = { .platform = "ppc405", }, { /* Xilinx Virtex-II Pro */ - .pvr_mask = 0xffff0000, + .pvr_mask = 0xfffff000, .pvr_value = 0x20010000, .cpu_name = "Virtex-II Pro", .cpu_features = CPU_FTRS_40X, @@ -901,6 +901,16 @@ struct cpu_spec cpu_specs[] = { .dcache_bsize = 32, .platform = "ppc405", }, + { /* Xilinx Virtex-4 FX */ + .pvr_mask = 0xfffff000, + .pvr_value = 0x20011000, + .cpu_name = "Virtex-4 FX", + .cpu_features = CPU_FTRS_40X, + .cpu_user_features = PPC_FEATURE_32 | + PPC_FEATURE_HAS_MMU | PPC_FEATURE_HAS_4xxMAC, + .icache_bsize = 32, + .dcache_bsize = 32, + }, { /* 405EP */ .pvr_mask = 0xffff0000, .pvr_value = 0x51210000, diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S index 388f861b8ed17d..79a0c910f0d873 100644 --- a/arch/powerpc/kernel/entry_64.S +++ b/arch/powerpc/kernel/entry_64.S @@ -1,6 +1,4 @@ /* - * arch/ppc64/kernel/entry.S - * * PowerPC version * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) * Rewritten by Cort Dougan (cort@cs.nmt.edu) for PReP @@ -374,7 +372,7 @@ _GLOBAL(ret_from_fork) * the fork code also. * * The code which creates the new task context is in 'copy_thread' - * in arch/ppc64/kernel/process.c + * in arch/powerpc/kernel/process.c */ .align 7 _GLOBAL(_switch) diff --git a/arch/powerpc/kernel/firmware.c b/arch/powerpc/kernel/firmware.c index 65eae752a527ca..4d37a3cb80f64c 100644 --- a/arch/powerpc/kernel/firmware.c +++ b/arch/powerpc/kernel/firmware.c @@ -18,28 +18,3 @@ #include <asm/firmware.h> unsigned long ppc64_firmware_features; - -#ifdef CONFIG_PPC_PSERIES -firmware_feature_t firmware_features_table[FIRMWARE_MAX_FEATURES] = { - {FW_FEATURE_PFT, "hcall-pft"}, - {FW_FEATURE_TCE, "hcall-tce"}, - {FW_FEATURE_SPRG0, "hcall-sprg0"}, - {FW_FEATURE_DABR, "hcall-dabr"}, - {FW_FEATURE_COPY, "hcall-copy"}, - {FW_FEATURE_ASR, "hcall-asr"}, - {FW_FEATURE_DEBUG, "hcall-debug"}, - {FW_FEATURE_PERF, "hcall-perf"}, - {FW_FEATURE_DUMP, "hcall-dump"}, - {FW_FEATURE_INTERRUPT, "hcall-interrupt"}, - {FW_FEATURE_MIGRATE, "hcall-migrate"}, - {FW_FEATURE_PERFMON, "hcall-perfmon"}, - {FW_FEATURE_CRQ, "hcall-crq"}, - {FW_FEATURE_VIO, "hcall-vio"}, - {FW_FEATURE_RDMA, "hcall-rdma"}, - {FW_FEATURE_LLAN, "hcall-lLAN"}, - {FW_FEATURE_BULK, "hcall-bulk"}, - {FW_FEATURE_XDABR, "hcall-xdabr"}, - {FW_FEATURE_MULTITCE, "hcall-multi-tce"}, - {FW_FEATURE_SPLPAR, "hcall-splpar"}, -}; -#endif diff --git a/arch/powerpc/kernel/head_44x.S b/arch/powerpc/kernel/head_44x.S index 8b49679fad549f..47c7fa148c9a99 100644 --- a/arch/powerpc/kernel/head_44x.S +++ b/arch/powerpc/kernel/head_44x.S @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/head_44x.S - * * Kernel execution entry point code. * * Copyright (c) 1995-1996 Gary Thomas <gdt@linuxppc.org> diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S index 11f2cd5af7dc5f..2b21ec4992854a 100644 --- a/arch/powerpc/kernel/head_64.S +++ b/arch/powerpc/kernel/head_64.S @@ -1,6 +1,4 @@ /* - * arch/ppc64/kernel/head.S - * * PowerPC version * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) * diff --git a/arch/powerpc/kernel/head_8xx.S b/arch/powerpc/kernel/head_8xx.S index bc6d1ac55235aa..28941f5ce6732c 100644 --- a/arch/powerpc/kernel/head_8xx.S +++ b/arch/powerpc/kernel/head_8xx.S @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/except_8xx.S - * * PowerPC version * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) * Rewritten by Cort Dougan (cort@cs.nmt.edu) for PReP diff --git a/arch/powerpc/kernel/head_booke.h b/arch/powerpc/kernel/head_booke.h new file mode 100644 index 00000000000000..8536e767616084 --- /dev/null +++ b/arch/powerpc/kernel/head_booke.h @@ -0,0 +1,363 @@ +#ifndef __HEAD_BOOKE_H__ +#define __HEAD_BOOKE_H__ + +/* + * Macros used for common Book-e exception handling + */ + +#define SET_IVOR(vector_number, vector_label) \ + li r26,vector_label@l; \ + mtspr SPRN_IVOR##vector_number,r26; \ + sync + +#define NORMAL_EXCEPTION_PROLOG \ + mtspr SPRN_SPRG0,r10; /* save two registers to work with */\ + mtspr SPRN_SPRG1,r11; \ + mtspr SPRN_SPRG4W,r1; \ + mfcr r10; /* save CR in r10 for now */\ + mfspr r11,SPRN_SRR1; /* check whether user or kernel */\ + andi. r11,r11,MSR_PR; \ + beq 1f; \ + mfspr r1,SPRN_SPRG3; /* if from user, start at top of */\ + lwz r1,THREAD_INFO-THREAD(r1); /* this thread's kernel stack */\ + addi r1,r1,THREAD_SIZE; \ +1: subi r1,r1,INT_FRAME_SIZE; /* Allocate an exception frame */\ + mr r11,r1; \ + stw r10,_CCR(r11); /* save various registers */\ + stw r12,GPR12(r11); \ + stw r9,GPR9(r11); \ + mfspr r10,SPRN_SPRG0; \ + stw r10,GPR10(r11); \ + mfspr r12,SPRN_SPRG1; \ + stw r12,GPR11(r11); \ + mflr r10; \ + stw r10,_LINK(r11); \ + mfspr r10,SPRN_SPRG4R; \ + mfspr r12,SPRN_SRR0; \ + stw r10,GPR1(r11); \ + mfspr r9,SPRN_SRR1; \ + stw r10,0(r11); \ + rlwinm r9,r9,0,14,12; /* clear MSR_WE (necessary?) */\ + stw r0,GPR0(r11); \ + SAVE_4GPRS(3, r11); \ + SAVE_2GPRS(7, r11) + +/* To handle the additional exception priority levels on 40x and Book-E + * processors we allocate a 4k stack per additional priority level. The various + * head_xxx.S files allocate space (exception_stack_top) for each priority's + * stack times the number of CPUs + * + * On 40x critical is the only additional level + * On 44x/e500 we have critical and machine check + * On e200 we have critical and debug (machine check occurs via critical) + * + * Additionally we reserve a SPRG for each priority level so we can free up a + * GPR to use as the base for indirect access to the exception stacks. This + * is necessary since the MMU is always on, for Book-E parts, and the stacks + * are offset from KERNELBASE. + * + */ +#define BOOKE_EXCEPTION_STACK_SIZE (8192) + +/* CRIT_SPRG only used in critical exception handling */ +#define CRIT_SPRG SPRN_SPRG2 +/* MCHECK_SPRG only used in machine check exception handling */ +#define MCHECK_SPRG SPRN_SPRG6W + +#define MCHECK_STACK_TOP (exception_stack_top - 4096) +#define CRIT_STACK_TOP (exception_stack_top) + +/* only on e200 for now */ +#define DEBUG_STACK_TOP (exception_stack_top - 4096) +#define DEBUG_SPRG SPRN_SPRG6W + +#ifdef CONFIG_SMP +#define BOOKE_LOAD_EXC_LEVEL_STACK(level) \ + mfspr r8,SPRN_PIR; \ + mulli r8,r8,BOOKE_EXCEPTION_STACK_SIZE; \ + neg r8,r8; \ + addis r8,r8,level##_STACK_TOP@ha; \ + addi r8,r8,level##_STACK_TOP@l +#else +#define BOOKE_LOAD_EXC_LEVEL_STACK(level) \ + lis r8,level##_STACK_TOP@h; \ + ori r8,r8,level##_STACK_TOP@l +#endif + +/* + * Exception prolog for critical/machine check exceptions. This is a + * little different from the normal exception prolog above since a + * critical/machine check exception can potentially occur at any point + * during normal exception processing. Thus we cannot use the same SPRG + * registers as the normal prolog above. Instead we use a portion of the + * critical/machine check exception stack at low physical addresses. + */ +#define EXC_LEVEL_EXCEPTION_PROLOG(exc_level, exc_level_srr0, exc_level_srr1) \ + mtspr exc_level##_SPRG,r8; \ + BOOKE_LOAD_EXC_LEVEL_STACK(exc_level);/* r8 points to the exc_level stack*/ \ + stw r10,GPR10-INT_FRAME_SIZE(r8); \ + stw r11,GPR11-INT_FRAME_SIZE(r8); \ + mfcr r10; /* save CR in r10 for now */\ + mfspr r11,exc_level_srr1; /* check whether user or kernel */\ + andi. r11,r11,MSR_PR; \ + mr r11,r8; \ + mfspr r8,exc_level##_SPRG; \ + beq 1f; \ + /* COMING FROM USER MODE */ \ + mfspr r11,SPRN_SPRG3; /* if from user, start at top of */\ + lwz r11,THREAD_INFO-THREAD(r11); /* this thread's kernel stack */\ + addi r11,r11,THREAD_SIZE; \ +1: subi r11,r11,INT_FRAME_SIZE; /* Allocate an exception frame */\ + stw r10,_CCR(r11); /* save various registers */\ + stw r12,GPR12(r11); \ + stw r9,GPR9(r11); \ + mflr r10; \ + stw r10,_LINK(r11); \ + mfspr r12,SPRN_DEAR; /* save DEAR and ESR in the frame */\ + stw r12,_DEAR(r11); /* since they may have had stuff */\ + mfspr r9,SPRN_ESR; /* in them at the point where the */\ + stw r9,_ESR(r11); /* exception was taken */\ + mfspr r12,exc_level_srr0; \ + stw r1,GPR1(r11); \ + mfspr r9,exc_level_srr1; \ + stw r1,0(r11); \ + mr r1,r11; \ + rlwinm r9,r9,0,14,12; /* clear MSR_WE (necessary?) */\ + stw r0,GPR0(r11); \ + SAVE_4GPRS(3, r11); \ + SAVE_2GPRS(7, r11) + +#define CRITICAL_EXCEPTION_PROLOG \ + EXC_LEVEL_EXCEPTION_PROLOG(CRIT, SPRN_CSRR0, SPRN_CSRR1) +#define DEBUG_EXCEPTION_PROLOG \ + EXC_LEVEL_EXCEPTION_PROLOG(DEBUG, SPRN_DSRR0, SPRN_DSRR1) +#define MCHECK_EXCEPTION_PROLOG \ + EXC_LEVEL_EXCEPTION_PROLOG(MCHECK, SPRN_MCSRR0, SPRN_MCSRR1) + +/* + * Exception vectors. + */ +#define START_EXCEPTION(label) \ + .align 5; \ +label: + +#define FINISH_EXCEPTION(func) \ + bl transfer_to_handler_full; \ + .long func; \ + .long ret_from_except_full + +#define EXCEPTION(n, label, hdlr, xfer) \ + START_EXCEPTION(label); \ + NORMAL_EXCEPTION_PROLOG; \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + xfer(n, hdlr) + +#define CRITICAL_EXCEPTION(n, label, hdlr) \ + START_EXCEPTION(label); \ + CRITICAL_EXCEPTION_PROLOG; \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + EXC_XFER_TEMPLATE(hdlr, n+2, (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), \ + NOCOPY, crit_transfer_to_handler, \ + ret_from_crit_exc) + +#define MCHECK_EXCEPTION(n, label, hdlr) \ + START_EXCEPTION(label); \ + MCHECK_EXCEPTION_PROLOG; \ + mfspr r5,SPRN_ESR; \ + stw r5,_ESR(r11); \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + EXC_XFER_TEMPLATE(hdlr, n+2, (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), \ + NOCOPY, mcheck_transfer_to_handler, \ + ret_from_mcheck_exc) + +#define EXC_XFER_TEMPLATE(hdlr, trap, msr, copyee, tfer, ret) \ + li r10,trap; \ + stw r10,_TRAP(r11); \ + lis r10,msr@h; \ + ori r10,r10,msr@l; \ + copyee(r10, r9); \ + bl tfer; \ + .long hdlr; \ + .long ret + +#define COPY_EE(d, s) rlwimi d,s,0,16,16 +#define NOCOPY(d, s) + +#define EXC_XFER_STD(n, hdlr) \ + EXC_XFER_TEMPLATE(hdlr, n, MSR_KERNEL, NOCOPY, transfer_to_handler_full, \ + ret_from_except_full) + +#define EXC_XFER_LITE(n, hdlr) \ + EXC_XFER_TEMPLATE(hdlr, n+1, MSR_KERNEL, NOCOPY, transfer_to_handler, \ + ret_from_except) + +#define EXC_XFER_EE(n, hdlr) \ + EXC_XFER_TEMPLATE(hdlr, n, MSR_KERNEL, COPY_EE, transfer_to_handler_full, \ + ret_from_except_full) + +#define EXC_XFER_EE_LITE(n, hdlr) \ + EXC_XFER_TEMPLATE(hdlr, n+1, MSR_KERNEL, COPY_EE, transfer_to_handler, \ + ret_from_except) + +/* Check for a single step debug exception while in an exception + * handler before state has been saved. This is to catch the case + * where an instruction that we are trying to single step causes + * an exception (eg ITLB/DTLB miss) and thus the first instruction of + * the exception handler generates a single step debug exception. + * + * If we get a debug trap on the first instruction of an exception handler, + * we reset the MSR_DE in the _exception handler's_ MSR (the debug trap is + * a critical exception, so we are using SPRN_CSRR1 to manipulate the MSR). + * The exception handler was handling a non-critical interrupt, so it will + * save (and later restore) the MSR via SPRN_CSRR1, which will still have + * the MSR_DE bit set. + */ +#ifdef CONFIG_E200 +#define DEBUG_EXCEPTION \ + START_EXCEPTION(Debug); \ + DEBUG_EXCEPTION_PROLOG; \ + \ + /* \ + * If there is a single step or branch-taken exception in an \ + * exception entry sequence, it was probably meant to apply to \ + * the code where the exception occurred (since exception entry \ + * doesn't turn off DE automatically). We simulate the effect \ + * of turning off DE on entry to an exception handler by turning \ + * off DE in the CSRR1 value and clearing the debug status. \ + */ \ + mfspr r10,SPRN_DBSR; /* check single-step/branch taken */ \ + andis. r10,r10,DBSR_IC@h; \ + beq+ 2f; \ + \ + lis r10,KERNELBASE@h; /* check if exception in vectors */ \ + ori r10,r10,KERNELBASE@l; \ + cmplw r12,r10; \ + blt+ 2f; /* addr below exception vectors */ \ + \ + lis r10,Debug@h; \ + ori r10,r10,Debug@l; \ + cmplw r12,r10; \ + bgt+ 2f; /* addr above exception vectors */ \ + \ + /* here it looks like we got an inappropriate debug exception. */ \ +1: rlwinm r9,r9,0,~MSR_DE; /* clear DE in the CDRR1 value */ \ + lis r10,DBSR_IC@h; /* clear the IC event */ \ + mtspr SPRN_DBSR,r10; \ + /* restore state and get out */ \ + lwz r10,_CCR(r11); \ + lwz r0,GPR0(r11); \ + lwz r1,GPR1(r11); \ + mtcrf 0x80,r10; \ + mtspr SPRN_DSRR0,r12; \ + mtspr SPRN_DSRR1,r9; \ + lwz r9,GPR9(r11); \ + lwz r12,GPR12(r11); \ + mtspr DEBUG_SPRG,r8; \ + BOOKE_LOAD_EXC_LEVEL_STACK(DEBUG); /* r8 points to the debug stack */ \ + lwz r10,GPR10-INT_FRAME_SIZE(r8); \ + lwz r11,GPR11-INT_FRAME_SIZE(r8); \ + mfspr r8,DEBUG_SPRG; \ + \ + RFDI; \ + b .; \ + \ + /* continue normal handling for a critical exception... */ \ +2: mfspr r4,SPRN_DBSR; \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + EXC_XFER_TEMPLATE(DebugException, 0x2002, (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), NOCOPY, debug_transfer_to_handler, ret_from_debug_exc) +#else +#define DEBUG_EXCEPTION \ + START_EXCEPTION(Debug); \ + CRITICAL_EXCEPTION_PROLOG; \ + \ + /* \ + * If there is a single step or branch-taken exception in an \ + * exception entry sequence, it was probably meant to apply to \ + * the code where the exception occurred (since exception entry \ + * doesn't turn off DE automatically). We simulate the effect \ + * of turning off DE on entry to an exception handler by turning \ + * off DE in the CSRR1 value and clearing the debug status. \ + */ \ + mfspr r10,SPRN_DBSR; /* check single-step/branch taken */ \ + andis. r10,r10,DBSR_IC@h; \ + beq+ 2f; \ + \ + lis r10,KERNELBASE@h; /* check if exception in vectors */ \ + ori r10,r10,KERNELBASE@l; \ + cmplw r12,r10; \ + blt+ 2f; /* addr below exception vectors */ \ + \ + lis r10,Debug@h; \ + ori r10,r10,Debug@l; \ + cmplw r12,r10; \ + bgt+ 2f; /* addr above exception vectors */ \ + \ + /* here it looks like we got an inappropriate debug exception. */ \ +1: rlwinm r9,r9,0,~MSR_DE; /* clear DE in the CSRR1 value */ \ + lis r10,DBSR_IC@h; /* clear the IC event */ \ + mtspr SPRN_DBSR,r10; \ + /* restore state and get out */ \ + lwz r10,_CCR(r11); \ + lwz r0,GPR0(r11); \ + lwz r1,GPR1(r11); \ + mtcrf 0x80,r10; \ + mtspr SPRN_CSRR0,r12; \ + mtspr SPRN_CSRR1,r9; \ + lwz r9,GPR9(r11); \ + lwz r12,GPR12(r11); \ + mtspr CRIT_SPRG,r8; \ + BOOKE_LOAD_EXC_LEVEL_STACK(CRIT); /* r8 points to the debug stack */ \ + lwz r10,GPR10-INT_FRAME_SIZE(r8); \ + lwz r11,GPR11-INT_FRAME_SIZE(r8); \ + mfspr r8,CRIT_SPRG; \ + \ + rfci; \ + b .; \ + \ + /* continue normal handling for a critical exception... */ \ +2: mfspr r4,SPRN_DBSR; \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + EXC_XFER_TEMPLATE(DebugException, 0x2002, (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), NOCOPY, crit_transfer_to_handler, ret_from_crit_exc) +#endif + +#define INSTRUCTION_STORAGE_EXCEPTION \ + START_EXCEPTION(InstructionStorage) \ + NORMAL_EXCEPTION_PROLOG; \ + mfspr r5,SPRN_ESR; /* Grab the ESR and save it */ \ + stw r5,_ESR(r11); \ + mr r4,r12; /* Pass SRR0 as arg2 */ \ + li r5,0; /* Pass zero as arg3 */ \ + EXC_XFER_EE_LITE(0x0400, handle_page_fault) + +#define ALIGNMENT_EXCEPTION \ + START_EXCEPTION(Alignment) \ + NORMAL_EXCEPTION_PROLOG; \ + mfspr r4,SPRN_DEAR; /* Grab the DEAR and save it */ \ + stw r4,_DEAR(r11); \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + EXC_XFER_EE(0x0600, alignment_exception) + +#define PROGRAM_EXCEPTION \ + START_EXCEPTION(Program) \ + NORMAL_EXCEPTION_PROLOG; \ + mfspr r4,SPRN_ESR; /* Grab the ESR and save it */ \ + stw r4,_ESR(r11); \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + EXC_XFER_STD(0x0700, program_check_exception) + +#define DECREMENTER_EXCEPTION \ + START_EXCEPTION(Decrementer) \ + NORMAL_EXCEPTION_PROLOG; \ + lis r0,TSR_DIS@h; /* Setup the DEC interrupt mask */ \ + mtspr SPRN_TSR,r0; /* Clear the DEC interrupt */ \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + EXC_XFER_LITE(0x0900, timer_interrupt) + +#define FP_UNAVAILABLE_EXCEPTION \ + START_EXCEPTION(FloatingPointUnavailable) \ + NORMAL_EXCEPTION_PROLOG; \ + bne load_up_fpu; /* if from user, just load it up */ \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + EXC_XFER_EE_LITE(0x800, kernel_fp_unavailable_exception) + +#endif /* __HEAD_BOOKE_H__ */ diff --git a/arch/powerpc/kernel/head_fsl_booke.S b/arch/powerpc/kernel/head_fsl_booke.S index 8d60fa99fc4b99..dd86bbed762711 100644 --- a/arch/powerpc/kernel/head_fsl_booke.S +++ b/arch/powerpc/kernel/head_fsl_booke.S @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/head_fsl_booke.S - * * Kernel execution entry point code. * * Copyright (c) 1995-1996 Gary Thomas <gdt@linuxppc.org> @@ -316,6 +314,7 @@ skpinv: addi r6,r6,1 /* Increment */ */ lis r2,DBCR0_IDM@h mtspr SPRN_DBCR0,r2 + isync /* clear any residual debug events */ li r2,-1 mtspr SPRN_DBSR,r2 @@ -1002,12 +1001,15 @@ _GLOBAL(giveup_fpu) _GLOBAL(abort) li r13,0 mtspr SPRN_DBCR0,r13 /* disable all debug events */ + isync mfmsr r13 ori r13,r13,MSR_DE@l /* Enable Debug Events */ mtmsr r13 + isync mfspr r13,SPRN_DBCR0 lis r13,(DBCR0_IDM|DBCR0_RST_CHIP)@h mtspr SPRN_DBCR0,r13 + isync _GLOBAL(set_context) diff --git a/arch/powerpc/kernel/iomap.c b/arch/powerpc/kernel/iomap.c index 6160c8dbb7c502..fd8214caedeedc 100644 --- a/arch/powerpc/kernel/iomap.c +++ b/arch/powerpc/kernel/iomap.c @@ -1,6 +1,4 @@ /* - * arch/ppc64/kernel/iomap.c - * * ppc64 "iomap" interface implementation. * * (C) Copyright 2004 Linus Torvalds diff --git a/arch/powerpc/kernel/iommu.c b/arch/powerpc/kernel/iommu.c index 946f3219fd29fc..d9a7fdef59b982 100644 --- a/arch/powerpc/kernel/iommu.c +++ b/arch/powerpc/kernel/iommu.c @@ -1,5 +1,4 @@ /* - * arch/ppc64/kernel/iommu.c * Copyright (C) 2001 Mike Corrigan & Dave Engebretsen, IBM Corporation * * Rewrite, cleanup, new allocation schemes, virtual merging: diff --git a/arch/powerpc/kernel/irq.c b/arch/powerpc/kernel/irq.c index d1fffce86df920..edb2b00edbd21a 100644 --- a/arch/powerpc/kernel/irq.c +++ b/arch/powerpc/kernel/irq.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/irq.c - * * Derived from arch/i386/kernel/irq.c * Copyright (C) 1992 Linus Torvalds * Adapted from arch/i386 by Gary Thomas diff --git a/arch/powerpc/kernel/kprobes.c b/arch/powerpc/kernel/kprobes.c index cfab48566db130..258039fb301642 100644 --- a/arch/powerpc/kernel/kprobes.c +++ b/arch/powerpc/kernel/kprobes.c @@ -1,6 +1,5 @@ /* * Kernel Probes (KProbes) - * arch/ppc64/kernel/kprobes.c * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by diff --git a/arch/powerpc/kernel/pci_iommu.c b/arch/powerpc/kernel/pci_iommu.c index bdf15dbbf4f0c4..c336f3e31cff3d 100644 --- a/arch/powerpc/kernel/pci_iommu.c +++ b/arch/powerpc/kernel/pci_iommu.c @@ -1,5 +1,4 @@ /* - * arch/ppc64/kernel/pci_iommu.c * Copyright (C) 2001 Mike Corrigan & Dave Engebretsen, IBM Corporation * * Rewrite, cleanup, new allocation schemes: diff --git a/arch/powerpc/kernel/ppc_ksyms.c b/arch/powerpc/kernel/ppc_ksyms.c index 8a731ea877b79b..af32922db65b8f 100644 --- a/arch/powerpc/kernel/ppc_ksyms.c +++ b/arch/powerpc/kernel/ppc_ksyms.c @@ -57,7 +57,6 @@ extern void machine_check_exception(struct pt_regs *regs); extern void alignment_exception(struct pt_regs *regs); extern void program_check_exception(struct pt_regs *regs); extern void single_step_exception(struct pt_regs *regs); -extern int pmac_newworld; extern int sys_sigreturn(struct pt_regs *regs); EXPORT_SYMBOL(clear_pages); diff --git a/arch/powerpc/kernel/process.c b/arch/powerpc/kernel/process.c index c225cf154bfeb0..dd774c3c930245 100644 --- a/arch/powerpc/kernel/process.c +++ b/arch/powerpc/kernel/process.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/process.c - * * Derived from "arch/i386/kernel/process.c" * Copyright (C) 1995 Linus Torvalds * diff --git a/arch/powerpc/kernel/prom.c b/arch/powerpc/kernel/prom.c index 294832a7e0a659..82d117c60d7f52 100644 --- a/arch/powerpc/kernel/prom.c +++ b/arch/powerpc/kernel/prom.c @@ -831,10 +831,6 @@ void __init unflatten_device_tree(void) /* Allocate memory for the expanded device tree */ mem = lmb_alloc(size + 4, __alignof__(struct device_node)); - if (!mem) { - DBG("Couldn't allocate memory with lmb_alloc()!\n"); - panic("Couldn't allocate memory with lmb_alloc()!\n"); - } mem = (unsigned long) __va(mem); ((u32 *)mem)[size / 4] = 0xdeadbeef; diff --git a/arch/powerpc/kernel/ptrace-common.h b/arch/powerpc/kernel/ptrace-common.h index 5ccbdbe0d5c96c..c42a860c8d25fd 100644 --- a/arch/powerpc/kernel/ptrace-common.h +++ b/arch/powerpc/kernel/ptrace-common.h @@ -1,6 +1,4 @@ /* - * linux/arch/ppc64/kernel/ptrace-common.h - * * Copyright (c) 2002 Stephen Rothwell, IBM Coproration * Extracted from ptrace.c and ptrace32.c * diff --git a/arch/powerpc/kernel/rtas-proc.c b/arch/powerpc/kernel/rtas-proc.c index 7a95b8a283548c..1f03fb28cc0af5 100644 --- a/arch/powerpc/kernel/rtas-proc.c +++ b/arch/powerpc/kernel/rtas-proc.c @@ -1,5 +1,4 @@ /* - * arch/ppc64/kernel/rtas-proc.c * Copyright (C) 2000 Tilmann Bitterberg * (tilmann@bitterberg.de) * diff --git a/arch/powerpc/kernel/rtas_pci.c b/arch/powerpc/kernel/rtas_pci.c index 5579f65599127a..03afb79e27e525 100644 --- a/arch/powerpc/kernel/rtas_pci.c +++ b/arch/powerpc/kernel/rtas_pci.c @@ -1,6 +1,4 @@ /* - * arch/ppc64/kernel/rtas_pci.c - * * Copyright (C) 2001 Dave Engebretsen, IBM Corporation * Copyright (C) 2003 Anton Blanchard <anton@au.ibm.com>, IBM * diff --git a/arch/powerpc/kernel/signal_64.c b/arch/powerpc/kernel/signal_64.c index 497a5d3df359e5..59b9c9cdd6a938 100644 --- a/arch/powerpc/kernel/signal_64.c +++ b/arch/powerpc/kernel/signal_64.c @@ -1,6 +1,4 @@ /* - * linux/arch/ppc64/kernel/signal.c - * * PowerPC version * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) * diff --git a/arch/powerpc/kernel/vdso.c b/arch/powerpc/kernel/vdso.c index f0c47dab090302..b316fda58b898f 100644 --- a/arch/powerpc/kernel/vdso.c +++ b/arch/powerpc/kernel/vdso.c @@ -1,6 +1,4 @@ /* - * linux/arch/ppc64/kernel/vdso.c - * * Copyright (C) 2004 Benjamin Herrenschmidt, IBM Corp. * <benh@kernel.crashing.org> * diff --git a/arch/powerpc/lib/copypage_64.S b/arch/powerpc/lib/copypage_64.S index 40523b140109e6..f9837f44ac0bac 100644 --- a/arch/powerpc/lib/copypage_64.S +++ b/arch/powerpc/lib/copypage_64.S @@ -1,6 +1,4 @@ /* - * arch/ppc64/lib/copypage.S - * * Copyright (C) 2002 Paul Mackerras, IBM Corp. * * This program is free software; you can redistribute it and/or diff --git a/arch/powerpc/lib/copyuser_64.S b/arch/powerpc/lib/copyuser_64.S index 6d69ef39b7df7c..a6b54cb97c4912 100644 --- a/arch/powerpc/lib/copyuser_64.S +++ b/arch/powerpc/lib/copyuser_64.S @@ -1,6 +1,4 @@ /* - * arch/ppc64/lib/copyuser.S - * * Copyright (C) 2002 Paul Mackerras, IBM Corp. * * This program is free software; you can redistribute it and/or diff --git a/arch/powerpc/lib/e2a.c b/arch/powerpc/lib/e2a.c index d2b834887920ac..4f88f4cc21e84f 100644 --- a/arch/powerpc/lib/e2a.c +++ b/arch/powerpc/lib/e2a.c @@ -1,9 +1,7 @@ /* - * arch/ppc64/lib/e2a.c - * * EBCDIC to ASCII conversion * - * This function moved here from arch/ppc64/kernel/viopath.c + * This function moved here from arch/powerpc/platforms/iseries/viopath.c * * (C) Copyright 2000-2004 IBM Corporation * diff --git a/arch/powerpc/lib/memcpy_64.S b/arch/powerpc/lib/memcpy_64.S index 9ccacdf5bcb952..fd66acfd3e3e12 100644 --- a/arch/powerpc/lib/memcpy_64.S +++ b/arch/powerpc/lib/memcpy_64.S @@ -1,6 +1,4 @@ /* - * arch/ppc64/lib/memcpy.S - * * Copyright (C) 2002 Paul Mackerras, IBM Corp. * * This program is free software; you can redistribute it and/or diff --git a/arch/powerpc/lib/rheap.c b/arch/powerpc/lib/rheap.c index 42c5de2c898f28..31e511856dc58b 100644 --- a/arch/powerpc/lib/rheap.c +++ b/arch/powerpc/lib/rheap.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/rheap.c - * * A Remote Heap. Remote means that we don't touch the memory that the * heap points to. Normal heap implementations use the memory they manage * to place their list. We cannot do that because the memory we manage may diff --git a/arch/powerpc/mm/fault.c b/arch/powerpc/mm/fault.c index a4815d316722cd..ec4adcb4bc28c6 100644 --- a/arch/powerpc/mm/fault.c +++ b/arch/powerpc/mm/fault.c @@ -1,6 +1,4 @@ /* - * arch/ppc/mm/fault.c - * * PowerPC version * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) * diff --git a/arch/powerpc/mm/hash_low_32.S b/arch/powerpc/mm/hash_low_32.S index 12ccd7155bacc5..ea469eefa14603 100644 --- a/arch/powerpc/mm/hash_low_32.S +++ b/arch/powerpc/mm/hash_low_32.S @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/hashtable.S - * * $Id: hashtable.S,v 1.6 1999/10/08 01:56:15 paulus Exp $ * * PowerPC version diff --git a/arch/powerpc/mm/hash_utils_64.c b/arch/powerpc/mm/hash_utils_64.c index b1f614c612dd13..ae2c919cbecd3f 100644 --- a/arch/powerpc/mm/hash_utils_64.c +++ b/arch/powerpc/mm/hash_utils_64.c @@ -431,7 +431,6 @@ void __init htab_initialize(void) * the absolute address space. */ table = lmb_alloc(htab_size_bytes, htab_size_bytes); - BUG_ON(table == 0); DBG("Hash table allocated at %lx, size: %lx\n", table, htab_size_bytes); diff --git a/arch/powerpc/mm/lmb.c b/arch/powerpc/mm/lmb.c index bbe3eac918e800..874cd103ce6ea2 100644 --- a/arch/powerpc/mm/lmb.c +++ b/arch/powerpc/mm/lmb.c @@ -31,6 +31,8 @@ #define DBG(fmt...) #endif +#define LMB_ALLOC_ANYWHERE 0 + struct lmb lmb; void lmb_dump_all(void) @@ -226,6 +228,20 @@ unsigned long __init lmb_alloc(unsigned long size, unsigned long align) unsigned long __init lmb_alloc_base(unsigned long size, unsigned long align, unsigned long max_addr) { + unsigned long alloc; + + alloc = __lmb_alloc_base(size, align, max_addr); + + if (alloc < 0) + panic("ERROR: Failed to allocate 0x%lx bytes below 0x%lx.\n", + size, max_addr); + + return alloc; +} + +unsigned long __init __lmb_alloc_base(unsigned long size, unsigned long align, + unsigned long max_addr) +{ long i, j; unsigned long base = 0; diff --git a/arch/powerpc/mm/mem.c b/arch/powerpc/mm/mem.c index 550517c2dd42ba..6809cdba6e9482 100644 --- a/arch/powerpc/mm/mem.c +++ b/arch/powerpc/mm/mem.c @@ -249,7 +249,6 @@ void __init do_init_bootmem(void) bootmap_pages = bootmem_bootmap_pages(total_pages); start = lmb_alloc(bootmap_pages << PAGE_SHIFT, PAGE_SIZE); - BUG_ON(!start); boot_mapsize = init_bootmem(start >> PAGE_SHIFT, total_pages); diff --git a/arch/powerpc/mm/mmap.c b/arch/powerpc/mm/mmap.c index fe65f522aff3a8..972a8e884b9aec 100644 --- a/arch/powerpc/mm/mmap.c +++ b/arch/powerpc/mm/mmap.c @@ -1,6 +1,4 @@ /* - * linux/arch/ppc64/mm/mmap.c - * * flexible mmap layout support * * Copyright 2003-2004 Red Hat Inc., Durham, North Carolina. diff --git a/arch/powerpc/mm/numa.c b/arch/powerpc/mm/numa.c index 2863a912bcd095..da5280f8cf42e7 100644 --- a/arch/powerpc/mm/numa.c +++ b/arch/powerpc/mm/numa.c @@ -570,11 +570,11 @@ static void __init *careful_allocation(int nid, unsigned long size, unsigned long end_pfn) { int new_nid; - unsigned long ret = lmb_alloc_base(size, align, end_pfn << PAGE_SHIFT); + unsigned long ret = __lmb_alloc_base(size, align, end_pfn << PAGE_SHIFT); /* retry over all memory */ if (!ret) - ret = lmb_alloc_base(size, align, lmb_end_of_DRAM()); + ret = __lmb_alloc_base(size, align, lmb_end_of_DRAM()); if (!ret) panic("numa.c: cannot allocate %lu bytes on node %d", diff --git a/arch/powerpc/mm/slb_low.S b/arch/powerpc/mm/slb_low.S index d1acee38f16326..abfaabf667bfb4 100644 --- a/arch/powerpc/mm/slb_low.S +++ b/arch/powerpc/mm/slb_low.S @@ -1,6 +1,4 @@ /* - * arch/ppc64/mm/slb_low.S - * * Low-level SLB routines * * Copyright (C) 2004 David Gibson <dwg@au.ibm.com>, IBM diff --git a/arch/powerpc/mm/stab.c b/arch/powerpc/mm/stab.c index 82e4951826bc79..91d25fb27f8940 100644 --- a/arch/powerpc/mm/stab.c +++ b/arch/powerpc/mm/stab.c @@ -247,10 +247,6 @@ void stabs_alloc(void) newstab = lmb_alloc_base(HW_PAGE_SIZE, HW_PAGE_SIZE, 1<<SID_SHIFT); - if (! newstab) - panic("Unable to allocate segment table for CPU %d.\n", - cpu); - newstab = (unsigned long)__va(newstab); memset((void *)newstab, 0, HW_PAGE_SIZE); diff --git a/arch/powerpc/mm/tlb_64.c b/arch/powerpc/mm/tlb_64.c index bb3afb6e631778..f734b11566c2a6 100644 --- a/arch/powerpc/mm/tlb_64.c +++ b/arch/powerpc/mm/tlb_64.c @@ -36,7 +36,7 @@ DEFINE_PER_CPU(struct ppc64_tlb_batch, ppc64_tlb_batch); /* This is declared as we are using the more or less generic - * include/asm-ppc64/tlb.h file -- tgall + * include/asm-powerpc/tlb.h file -- tgall */ DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); DEFINE_PER_CPU(struct pte_freelist_batch *, pte_freelist_cur); diff --git a/arch/powerpc/platforms/83xx/Makefile b/arch/powerpc/platforms/83xx/Makefile index 9d8b28ef33435a..5c72367441a83d 100644 --- a/arch/powerpc/platforms/83xx/Makefile +++ b/arch/powerpc/platforms/83xx/Makefile @@ -1,4 +1,6 @@ # # Makefile for the PowerPC 83xx linux kernel. # -obj-$(CONFIG_MPC834x_SYS) += mpc834x_sys.o pci.o +obj-y := misc.o +obj-$(CONFIG_PCI) += pci.o +obj-$(CONFIG_MPC834x_SYS) += mpc834x_sys.o diff --git a/arch/powerpc/platforms/83xx/misc.c b/arch/powerpc/platforms/83xx/misc.c new file mode 100644 index 00000000000000..0eb3d99f1b93d4 --- /dev/null +++ b/arch/powerpc/platforms/83xx/misc.c @@ -0,0 +1,55 @@ +/* + * misc setup functions for MPC83xx + * + * Maintainer: Kumar Gala <galak@kernel.crashing.org> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/config.h> +#include <linux/stddef.h> +#include <linux/kernel.h> + +#include <asm/io.h> +#include <asm/hw_irq.h> +#include <sysdev/fsl_soc.h> + +#include "mpc83xx.h" + +void mpc83xx_restart(char *cmd) +{ +#define RST_OFFSET 0x00000900 +#define RST_PROT_REG 0x00000018 +#define RST_CTRL_REG 0x0000001c + __be32 __iomem *reg; + + /* map reset register space */ + reg = ioremap(get_immrbase() + 0x900, 0xff); + + local_irq_disable(); + + /* enable software reset "RSTE" */ + out_be32(reg + (RST_PROT_REG >> 2), 0x52535445); + + /* set software hard reset */ + out_be32(reg + (RST_CTRL_REG >> 2), 0x52535445); + for (;;) ; +} + +long __init mpc83xx_time_init(void) +{ +#define SPCR_OFFSET 0x00000110 +#define SPCR_TBEN 0x00400000 + __be32 __iomem *spcr = ioremap(get_immrbase() + SPCR_OFFSET, 4); + __be32 tmp; + + tmp = in_be32(spcr); + out_be32(spcr, tmp | SPCR_TBEN); + + iounmap(spcr); + + return 0; +} diff --git a/arch/powerpc/platforms/83xx/mpc834x_sys.c b/arch/powerpc/platforms/83xx/mpc834x_sys.c index 2098dd05a773c1..7c18b4cd5db437 100644 --- a/arch/powerpc/platforms/83xx/mpc834x_sys.c +++ b/arch/powerpc/platforms/83xx/mpc834x_sys.c @@ -24,22 +24,15 @@ #include <linux/delay.h> #include <linux/seq_file.h> #include <linux/root_dev.h> -#include <linux/module.h> -#include <linux/fsl_devices.h> #include <asm/system.h> -#include <asm/pgtable.h> -#include <asm/page.h> #include <asm/atomic.h> #include <asm/time.h> #include <asm/io.h> #include <asm/machdep.h> #include <asm/ipic.h> #include <asm/bootinfo.h> -#include <asm/pci-bridge.h> -#include <asm/mpc83xx.h> #include <asm/irq.h> -#include <mm/mmu_decl.h> #include <asm/prom.h> #include <asm/udbg.h> #include <sysdev/fsl_soc.h> @@ -52,8 +45,6 @@ unsigned long isa_mem_base = 0; #endif #ifdef CONFIG_PCI -extern int mpc83xx_pci2_busno; - static int mpc83xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin) { @@ -78,26 +69,14 @@ mpc83xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin) const long min_idsel = 0x11, max_idsel = 0x20, irqs_per_slot = 4; return PCI_IRQ_TABLE_LOOKUP; } - -static int -mpc83xx_exclude_device(u_char bus, u_char devfn) -{ - if (bus == 0 && PCI_SLOT(devfn) == 0) - return PCIBIOS_DEVICE_NOT_FOUND; - if (mpc83xx_pci2_busno) - if (bus == (mpc83xx_pci2_busno) && PCI_SLOT(devfn) == 0) - return PCIBIOS_DEVICE_NOT_FOUND; - return PCIBIOS_SUCCESSFUL; -} -#endif /* CONFIG_PCI */ +#endif /* CONFIG_PCI */ /* ************************************************************************ * * Setup the architecture * */ -static void __init -mpc834x_sys_setup_arch(void) +static void __init mpc834x_sys_setup_arch(void) { struct device_node *np; @@ -106,14 +85,14 @@ mpc834x_sys_setup_arch(void) np = of_find_node_by_type(NULL, "cpu"); if (np != 0) { - unsigned int *fp = (int *) get_property(np, "clock-frequency", NULL); + unsigned int *fp = + (int *)get_property(np, "clock-frequency", NULL); if (fp != 0) loops_per_jiffy = *fp / HZ; else loops_per_jiffy = 50000000 / HZ; of_node_put(np); } - #ifdef CONFIG_PCI for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;) add_bridge(np); @@ -124,14 +103,13 @@ mpc834x_sys_setup_arch(void) #endif #ifdef CONFIG_ROOT_NFS - ROOT_DEV = Root_NFS; + ROOT_DEV = Root_NFS; #else - ROOT_DEV = Root_HDA1; + ROOT_DEV = Root_HDA1; #endif } -void __init -mpc834x_sys_init_IRQ(void) +void __init mpc834x_sys_init_IRQ(void) { u8 senses[8] = { 0, /* EXT 0 */ @@ -160,64 +138,27 @@ mpc834x_sys_init_IRQ(void) } #if defined(CONFIG_I2C_MPC) && defined(CONFIG_SENSORS_DS1374) -extern ulong ds1374_get_rtc_time(void); -extern int ds1374_set_rtc_time(ulong); +extern ulong ds1374_get_rtc_time(void); +extern int ds1374_set_rtc_time(ulong); -static int __init -mpc834x_rtc_hookup(void) +static int __init mpc834x_rtc_hookup(void) { - struct timespec tv; + struct timespec tv; ppc_md.get_rtc_time = ds1374_get_rtc_time; ppc_md.set_rtc_time = ds1374_set_rtc_time; tv.tv_nsec = 0; - tv.tv_sec = (ppc_md.get_rtc_time)(); + tv.tv_sec = (ppc_md.get_rtc_time) (); do_settimeofday(&tv); return 0; } + late_initcall(mpc834x_rtc_hookup); #endif -static void -mpc83xx_restart(char *cmd) -{ -#define RST_OFFSET 0x00000900 -#define RST_PROT_REG 0x00000018 -#define RST_CTRL_REG 0x0000001c - __be32 __iomem *reg; - - // map reset register space - reg = ioremap(get_immrbase() + 0x900, 0xff); - - local_irq_disable(); - - /* enable software reset "RSTE" */ - out_be32(reg + (RST_PROT_REG >> 2), 0x52535445); - - /* set software hard reset */ - out_be32(reg + (RST_CTRL_REG >> 2), 0x52535445); - for(;;); -} - -static long __init -mpc83xx_time_init(void) -{ -#define SPCR_OFFSET 0x00000110 -#define SPCR_TBEN 0x00400000 - __be32 __iomem *spcr = ioremap(get_immrbase() + SPCR_OFFSET, 4); - __be32 tmp; - - tmp = in_be32(spcr); - out_be32(spcr, tmp|SPCR_TBEN); - - iounmap(spcr); - - return 0; -} -void __init -platform_init(void) +void __init platform_init(void) { /* setup the PowerPC module struct */ ppc_md.setup_arch = mpc834x_sys_setup_arch; @@ -239,5 +180,3 @@ platform_init(void) return; } - - diff --git a/arch/powerpc/platforms/83xx/mpc834x_sys.h b/arch/powerpc/platforms/83xx/mpc834x_sys.h index e4ca39f6a86205..fedecb73f7ffc8 100644 --- a/arch/powerpc/platforms/83xx/mpc834x_sys.h +++ b/arch/powerpc/platforms/83xx/mpc834x_sys.h @@ -20,4 +20,4 @@ #define PIRQC MPC83xx_IRQ_EXT6 #define PIRQD MPC83xx_IRQ_EXT7 -#endif /* __MACH_MPC83XX_SYS_H__ */ +#endif /* __MACH_MPC83XX_SYS_H__ */ diff --git a/arch/powerpc/platforms/83xx/mpc83xx.h b/arch/powerpc/platforms/83xx/mpc83xx.h index ce9e66abef24ac..01cae106912bec 100644 --- a/arch/powerpc/platforms/83xx/mpc83xx.h +++ b/arch/powerpc/platforms/83xx/mpc83xx.h @@ -10,5 +10,8 @@ */ extern int add_bridge(struct device_node *dev); +extern int mpc83xx_exclude_device(u_char bus, u_char devfn); +extern void mpc83xx_restart(char *cmd); +extern long mpc83xx_time_init(void); -#endif /* __MPC83XX_H__ */ +#endif /* __MPC83XX_H__ */ diff --git a/arch/powerpc/platforms/83xx/pci.c b/arch/powerpc/platforms/83xx/pci.c index 469cdacc5bd418..16f7d3b30e1dbf 100644 --- a/arch/powerpc/platforms/83xx/pci.c +++ b/arch/powerpc/platforms/83xx/pci.c @@ -36,7 +36,16 @@ int mpc83xx_pci2_busno; -#ifdef CONFIG_PCI +int mpc83xx_exclude_device(u_char bus, u_char devfn) +{ + if (bus == 0 && PCI_SLOT(devfn) == 0) + return PCIBIOS_DEVICE_NOT_FOUND; + if (mpc83xx_pci2_busno) + if (bus == (mpc83xx_pci2_busno) && PCI_SLOT(devfn) == 0) + return PCIBIOS_DEVICE_NOT_FOUND; + return PCIBIOS_SUCCESSFUL; +} + int __init add_bridge(struct device_node *dev) { int len; @@ -52,7 +61,7 @@ int __init add_bridge(struct device_node *dev) has_address = (of_address_to_resource(dev, 0, &rsrc) == 0); /* Get bus range if any */ - bus_range = (int *) get_property(dev, "bus-range", &len); + bus_range = (int *)get_property(dev, "bus-range", &len); if (bus_range == NULL || len < 2 * sizeof(int)) { printk(KERN_WARNING "Can't get bus-range for %s, assume" " bus 0\n", dev->full_name); @@ -74,7 +83,7 @@ int __init add_bridge(struct device_node *dev) if ((rsrc.start & 0xfffff) == 0x8500) { setup_indirect_pci(hose, immr + 0x8300, immr + 0x8304); } - /* PCI 2*/ + /* PCI 2 */ if ((rsrc.start & 0xfffff) == 0x8600) { setup_indirect_pci(hose, immr + 0x8380, immr + 0x8384); primary = 0; @@ -84,10 +93,10 @@ int __init add_bridge(struct device_node *dev) printk(KERN_INFO "Found MPC83xx PCI host bridge at 0x%08lx. " "Firmware bus number: %d->%d\n", - rsrc.start, hose->first_busno, hose->last_busno); + rsrc.start, hose->first_busno, hose->last_busno); DBG(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n", - hose, hose->cfg_addr, hose->cfg_data); + hose, hose->cfg_addr, hose->cfg_data); /* Interpret the "ranges" property */ /* This also maps the I/O region and sets isa_io/mem_base */ @@ -95,5 +104,3 @@ int __init add_bridge(struct device_node *dev) return 0; } - -#endif diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig index c5bc2821d99162..d3d0ff745e8428 100644 --- a/arch/powerpc/platforms/85xx/Kconfig +++ b/arch/powerpc/platforms/85xx/Kconfig @@ -1,86 +1,30 @@ -config 85xx - bool - depends on E500 - default y - -config PPC_INDIRECT_PCI_BE - bool - depends on 85xx - default y - -menu "Freescale 85xx options" - depends on E500 +menu "Platform support" + depends on PPC_85xx choice prompt "Machine Type" - depends on 85xx default MPC8540_ADS config MPC8540_ADS bool "Freescale MPC8540 ADS" help - This option enables support for the MPC 8540 ADS evaluation board. - -config MPC8548_CDS - bool "Freescale MPC8548 CDS" - help - This option enablese support for the MPC8548 CDS evaluation board. - -config MPC8555_CDS - bool "Freescale MPC8555 CDS" - help - This option enablese support for the MPC8555 CDS evaluation board. - -config MPC8560_ADS - bool "Freescale MPC8560 ADS" - help - This option enables support for the MPC 8560 ADS evaluation board. - -config SBC8560 - bool "WindRiver PowerQUICC III SBC8560" - help - This option enables support for the WindRiver PowerQUICC III - SBC8560 board. - -config STX_GP3 - bool "Silicon Turnkey Express GP3" - help - This option enables support for the Silicon Turnkey Express GP3 - board. + This option enables support for the MPC 8540 ADS board endchoice -# It's often necessary to know the specific 85xx processor type. -# Fortunately, it is implied (so far) from the board type, so we -# don't need to ask more redundant questions. config MPC8540 bool - depends on MPC8540_ADS - default y - -config MPC8548 - bool - depends on MPC8548_CDS - default y + select PPC_UDBG_16550 + select PPC_INDIRECT_PCI + default y if MPC8540_ADS -config MPC8555 - bool - depends on MPC8555_CDS - default y - -config MPC8560 +config PPC_INDIRECT_PCI_BE bool - depends on SBC8560 || MPC8560_ADS || STX_GP3 - default y - -config 85xx_PCI2 - bool "Supprt for 2nd PCI host controller" - depends on MPC8555_CDS + depends on PPC_85xx default y -config PPC_GEN550 +config MPIC bool - depends on MPC8540 || SBC8560 || MPC8555 default y endmenu diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile index 6407197ffd8939..70e1190809f89e 100644 --- a/arch/powerpc/platforms/85xx/Makefile +++ b/arch/powerpc/platforms/85xx/Makefile @@ -1 +1,4 @@ -# empty makefile so make clean works +# +# Makefile for the PowerPC 85xx linux kernel. +# +obj-$(CONFIG_PPC_85xx) += misc.o mpc85xx_ads.o diff --git a/arch/powerpc/platforms/85xx/misc.c b/arch/powerpc/platforms/85xx/misc.c new file mode 100644 index 00000000000000..26c5e822c7c8f2 --- /dev/null +++ b/arch/powerpc/platforms/85xx/misc.c @@ -0,0 +1,31 @@ +/* + * MPC85xx generic code. + * + * Maintained by Kumar Gala (see MAINTAINERS for contact information) + * + * Copyright 2005 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#include <linux/irq.h> +#include <linux/module.h> +#include <asm/irq.h> + +extern void abort(void); + +void mpc85xx_restart(char *cmd) +{ + local_irq_disable(); + abort(); +} + +/* For now this is a pass through */ +phys_addr_t fixup_bigphys_addr(phys_addr_t addr, phys_addr_t size) +{ + return addr; +}; + +EXPORT_SYMBOL(fixup_bigphys_addr); diff --git a/arch/powerpc/platforms/85xx/mpc8540_ads.h b/arch/powerpc/platforms/85xx/mpc8540_ads.h new file mode 100644 index 00000000000000..b3ec88caad11c3 --- /dev/null +++ b/arch/powerpc/platforms/85xx/mpc8540_ads.h @@ -0,0 +1,60 @@ +/* + * arch/ppc/platforms/85xx/mpc8540_ads.h + * + * MPC8540ADS board definitions + * + * Maintainer: Kumar Gala <kumar.gala@freescale.com> + * + * Copyright 2004 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#ifndef __MACH_MPC8540ADS_H__ +#define __MACH_MPC8540ADS_H__ + +#include <linux/config.h> +#include <linux/initrd.h> + +#define BOARD_CCSRBAR ((uint)0xe0000000) +#define BCSR_ADDR ((uint)0xf8000000) +#define BCSR_SIZE ((uint)(32 * 1024)) + +/* PCI interrupt controller */ +#define PIRQA MPC85xx_IRQ_EXT1 +#define PIRQB MPC85xx_IRQ_EXT2 +#define PIRQC MPC85xx_IRQ_EXT3 +#define PIRQD MPC85xx_IRQ_EXT4 + +#define MPC85XX_PCI1_LOWER_IO 0x00000000 +#define MPC85XX_PCI1_UPPER_IO 0x00ffffff + +#define MPC85XX_PCI1_LOWER_MEM 0x80000000 +#define MPC85XX_PCI1_UPPER_MEM 0x9fffffff + +#define MPC85XX_PCI1_IO_BASE 0xe2000000 +#define MPC85XX_PCI1_MEM_OFFSET 0x00000000 + +#define MPC85XX_PCI1_IO_SIZE 0x01000000 + +/* PCI config */ +#define PCI1_CFG_ADDR_OFFSET (0x8000) +#define PCI1_CFG_DATA_OFFSET (0x8004) + +#define PCI2_CFG_ADDR_OFFSET (0x9000) +#define PCI2_CFG_DATA_OFFSET (0x9004) + +/* Additional register for PCI-X configuration */ +#define PCIX_NEXT_CAP 0x60 +#define PCIX_CAP_ID 0x61 +#define PCIX_COMMAND 0x62 +#define PCIX_STATUS 0x64 + +/* Offset of CPM register space */ +#define CPM_MAP_ADDR (CCSRBAR + MPC85xx_CPM_OFFSET) + +#endif /* __MACH_MPC8540ADS_H__ */ diff --git a/arch/powerpc/platforms/85xx/mpc85xx.h b/arch/powerpc/platforms/85xx/mpc85xx.h new file mode 100644 index 00000000000000..be75abb2a2836f --- /dev/null +++ b/arch/powerpc/platforms/85xx/mpc85xx.h @@ -0,0 +1,17 @@ +/* + * arch/ppc/platforms/85xx/mpc85xx.h + * + * MPC85xx soc definitions/function decls + * + * Maintainer: Kumar Gala <kumar.gala@freescale.com> + * + * Copyright 2005 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +extern void mpc85xx_restart(char *); diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ads.c b/arch/powerpc/platforms/85xx/mpc85xx_ads.c new file mode 100644 index 00000000000000..ba6798d4765423 --- /dev/null +++ b/arch/powerpc/platforms/85xx/mpc85xx_ads.c @@ -0,0 +1,177 @@ +/* + * MPC85xx setup and early boot code plus other random bits. + * + * Maintained by Kumar Gala (see MAINTAINERS for contact information) + * + * Copyright 2005 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/config.h> +#include <linux/stddef.h> +#include <linux/kernel.h> +#include <linux/pci.h> +#include <linux/kdev_t.h> +#include <linux/delay.h> +#include <linux/seq_file.h> +#include <linux/root_dev.h> + +#include <asm/system.h> +#include <asm/time.h> +#include <asm/machdep.h> +#include <asm/pci-bridge.h> +#include <asm/mpc85xx.h> +#include <asm/prom.h> +#include <asm/mpic.h> +#include <mm/mmu_decl.h> +#include <asm/udbg.h> + +#include <sysdev/fsl_soc.h> +#include "mpc85xx.h" + +#ifndef CONFIG_PCI +unsigned long isa_io_base = 0; +unsigned long isa_mem_base = 0; +#endif + +/* + * Internal interrupts are all Level Sensitive, and Positive Polarity + * + * Note: Likely, this table and the following function should be + * obtained and derived from the OF Device Tree. + */ +static u_char mpc85xx_ads_openpic_initsenses[] __initdata = { + MPC85XX_INTERNAL_IRQ_SENSES, + 0x0, /* External 0: */ +#if defined(CONFIG_PCI) + (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* Ext 1: PCI slot 0 */ + (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* Ext 2: PCI slot 1 */ + (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* Ext 3: PCI slot 2 */ + (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* Ext 4: PCI slot 3 */ +#else + 0x0, /* External 1: */ + 0x0, /* External 2: */ + 0x0, /* External 3: */ + 0x0, /* External 4: */ +#endif + (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* External 5: PHY */ + 0x0, /* External 6: */ + (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* External 7: PHY */ + 0x0, /* External 8: */ + 0x0, /* External 9: */ + 0x0, /* External 10: */ + 0x0, /* External 11: */ +}; + +void __init mpc85xx_ads_pic_init(void) +{ + struct mpic *mpic1; + phys_addr_t OpenPIC_PAddr; + + /* Determine the Physical Address of the OpenPIC regs */ + OpenPIC_PAddr = get_immrbase() + MPC85xx_OPENPIC_OFFSET; + + mpic1 = mpic_alloc(OpenPIC_PAddr, + MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN, + 4, MPC85xx_OPENPIC_IRQ_OFFSET, 0, 250, + mpc85xx_ads_openpic_initsenses, + sizeof(mpc85xx_ads_openpic_initsenses), + " OpenPIC "); + BUG_ON(mpic1 == NULL); + mpic_assign_isu(mpic1, 0, OpenPIC_PAddr + 0x10200); + mpic_assign_isu(mpic1, 1, OpenPIC_PAddr + 0x10280); + mpic_assign_isu(mpic1, 2, OpenPIC_PAddr + 0x10300); + mpic_assign_isu(mpic1, 3, OpenPIC_PAddr + 0x10380); + mpic_assign_isu(mpic1, 4, OpenPIC_PAddr + 0x10400); + mpic_assign_isu(mpic1, 5, OpenPIC_PAddr + 0x10480); + mpic_assign_isu(mpic1, 6, OpenPIC_PAddr + 0x10500); + mpic_assign_isu(mpic1, 7, OpenPIC_PAddr + 0x10580); + + /* dummy mappings to get to 48 */ + mpic_assign_isu(mpic1, 8, OpenPIC_PAddr + 0x10600); + mpic_assign_isu(mpic1, 9, OpenPIC_PAddr + 0x10680); + mpic_assign_isu(mpic1, 10, OpenPIC_PAddr + 0x10700); + mpic_assign_isu(mpic1, 11, OpenPIC_PAddr + 0x10780); + + /* External ints */ + mpic_assign_isu(mpic1, 12, OpenPIC_PAddr + 0x10000); + mpic_assign_isu(mpic1, 13, OpenPIC_PAddr + 0x10080); + mpic_assign_isu(mpic1, 14, OpenPIC_PAddr + 0x10100); + mpic_init(mpic1); +} + +/* + * Setup the architecture + */ +static void __init mpc85xx_ads_setup_arch(void) +{ + struct device_node *cpu; + + if (ppc_md.progress) + ppc_md.progress("mpc85xx_ads_setup_arch()", 0); + + cpu = of_find_node_by_type(NULL, "cpu"); + if (cpu != 0) { + unsigned int *fp; + + fp = (int *)get_property(cpu, "clock-frequency", NULL); + if (fp != 0) + loops_per_jiffy = *fp / HZ; + else + loops_per_jiffy = 50000000 / HZ; + of_node_put(cpu); + } +#ifdef CONFIG_ROOT_NFS + ROOT_DEV = Root_NFS; +#else + ROOT_DEV = Root_HDA1; +#endif +} + +void mpc85xx_ads_show_cpuinfo(struct seq_file *m) +{ + uint pvid, svid, phid1; + uint memsize = total_memory; + + pvid = mfspr(SPRN_PVR); + svid = mfspr(SPRN_SVR); + + seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n"); + seq_printf(m, "Machine\t\t: mpc85xx\n"); + seq_printf(m, "PVR\t\t: 0x%x\n", pvid); + seq_printf(m, "SVR\t\t: 0x%x\n", svid); + + /* Display cpu Pll setting */ + phid1 = mfspr(SPRN_HID1); + seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f)); + + /* Display the amount of memory */ + seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024)); +} + +void __init platform_init(void) +{ + ppc_md.setup_arch = mpc85xx_ads_setup_arch; + ppc_md.show_cpuinfo = mpc85xx_ads_show_cpuinfo; + + ppc_md.init_IRQ = mpc85xx_ads_pic_init; + ppc_md.get_irq = mpic_get_irq; + + ppc_md.restart = mpc85xx_restart; + ppc_md.power_off = NULL; + ppc_md.halt = NULL; + + ppc_md.time_init = NULL; + ppc_md.set_rtc_time = NULL; + ppc_md.get_rtc_time = NULL; + ppc_md.calibrate_decr = generic_calibrate_decr; + + ppc_md.progress = udbg_progress; + + if (ppc_md.progress) + ppc_md.progress("mpc85xx_ads platform_init(): exit", 0); +} diff --git a/arch/powerpc/platforms/Makefile b/arch/powerpc/platforms/Makefile index 04073fd987ec46..c4f6b0d2d14000 100644 --- a/arch/powerpc/platforms/Makefile +++ b/arch/powerpc/platforms/Makefile @@ -8,7 +8,7 @@ endif obj-$(CONFIG_PPC_CHRP) += chrp/ obj-$(CONFIG_4xx) += 4xx/ obj-$(CONFIG_PPC_83xx) += 83xx/ -obj-$(CONFIG_85xx) += 85xx/ +obj-$(CONFIG_PPC_85xx) += 85xx/ obj-$(CONFIG_PPC_PSERIES) += pseries/ obj-$(CONFIG_PPC_ISERIES) += iseries/ obj-$(CONFIG_PPC_MAPLE) += maple/ diff --git a/arch/powerpc/platforms/chrp/pegasos_eth.c b/arch/powerpc/platforms/chrp/pegasos_eth.c index 29c86781c49365..6ad4b1a72c96b9 100644 --- a/arch/powerpc/platforms/chrp/pegasos_eth.c +++ b/arch/powerpc/platforms/chrp/pegasos_eth.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/chrp_pegasos_eth.c - * * Copyright (C) 2005 Sven Luther <sl@bplan-gmbh.de> * Thanks to : * Dale Farnsworth <dale@farnsworth.org> diff --git a/arch/powerpc/platforms/chrp/setup.c b/arch/powerpc/platforms/chrp/setup.c index e1fadbf49150d3..8bf4307e323df5 100644 --- a/arch/powerpc/platforms/chrp/setup.c +++ b/arch/powerpc/platforms/chrp/setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/setup.c - * * Copyright (C) 1995 Linus Torvalds * Adapted from 'alpha' version by Gary Thomas * Modified by Cort Dougan (cort@cs.nmt.edu) diff --git a/arch/powerpc/platforms/chrp/time.c b/arch/powerpc/platforms/chrp/time.c index 78df2e7ca88a1c..12c6f689b1aa44 100644 --- a/arch/powerpc/platforms/chrp/time.c +++ b/arch/powerpc/platforms/chrp/time.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/chrp_time.c - * * Copyright (C) 1991, 1992, 1995 Linus Torvalds * * Adapted for PowerPC (PReP) by Gary Thomas diff --git a/arch/powerpc/platforms/maple/time.c b/arch/powerpc/platforms/maple/time.c index 50bc4eb853535b..5e6981d1737935 100644 --- a/arch/powerpc/platforms/maple/time.c +++ b/arch/powerpc/platforms/maple/time.c @@ -1,6 +1,4 @@ /* - * arch/ppc64/kernel/maple_time.c - * * (c) Copyright 2004 Benjamin Herrenschmidt (benh@kernel.crashing.org), * IBM Corp. * diff --git a/arch/powerpc/platforms/powermac/cpufreq_32.c b/arch/powerpc/platforms/powermac/cpufreq_32.c index 56fd4e05fede95..cfd6527a0d7e07 100644 --- a/arch/powerpc/platforms/powermac/cpufreq_32.c +++ b/arch/powerpc/platforms/powermac/cpufreq_32.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/pmac_cpufreq.c - * * Copyright (C) 2002 - 2005 Benjamin Herrenschmidt <benh@kernel.crashing.org> * Copyright (C) 2004 John Steele Scott <toojays@toojays.net> * diff --git a/arch/powerpc/platforms/powermac/feature.c b/arch/powerpc/platforms/powermac/feature.c index 34714d3ea69a1f..c8b4a2b115a9fd 100644 --- a/arch/powerpc/platforms/powermac/feature.c +++ b/arch/powerpc/platforms/powermac/feature.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/pmac_feature.c - * * Copyright (C) 1996-2001 Paul Mackerras (paulus@cs.anu.edu.au) * Ben. Herrenschmidt (benh@kernel.crashing.org) * diff --git a/arch/powerpc/platforms/powermac/nvram.c b/arch/powerpc/platforms/powermac/nvram.c index 3ebd045a335048..5fd28995c74cea 100644 --- a/arch/powerpc/platforms/powermac/nvram.c +++ b/arch/powerpc/platforms/powermac/nvram.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/pmac_nvram.c - * * Copyright (C) 2002 Benjamin Herrenschmidt (benh@kernel.crashing.org) * * This program is free software; you can redistribute it and/or diff --git a/arch/powerpc/platforms/powermac/setup.c b/arch/powerpc/platforms/powermac/setup.c index 1955462f4082fa..97c54e19c1b550 100644 --- a/arch/powerpc/platforms/powermac/setup.c +++ b/arch/powerpc/platforms/powermac/setup.c @@ -86,11 +86,10 @@ int ppc_override_l2cr = 0; int ppc_override_l2cr_value; int has_l2cache = 0; -int pmac_newworld = 1; +int pmac_newworld; static int current_root_goodness = -1; -extern int pmac_newworld; extern struct machdep_calls pmac_md; #define DEFAULT_ROOT_DEVICE Root_SDA1 /* sda1 - slightly silly choice */ @@ -308,9 +307,10 @@ static void __init pmac_setup_arch(void) for (ic = NULL; (ic = of_find_all_nodes(ic)) != NULL; ) if (get_property(ic, "interrupt-controller", NULL)) break; - pmac_newworld = (ic != NULL); - if (ic) + if (ic) { + pmac_newworld = 1; of_node_put(ic); + } /* Lookup PCI hosts */ pmac_pci_init(); diff --git a/arch/powerpc/platforms/pseries/Makefile b/arch/powerpc/platforms/pseries/Makefile index 61616d14407293..930898635c9ffa 100644 --- a/arch/powerpc/platforms/pseries/Makefile +++ b/arch/powerpc/platforms/pseries/Makefile @@ -1,5 +1,6 @@ obj-y := pci.o lpar.o hvCall.o nvram.o reconfig.o \ - setup.o iommu.o ras.o rtasd.o pci_dlpar.o + setup.o iommu.o ras.o rtasd.o pci_dlpar.o \ + firmware.o obj-$(CONFIG_SMP) += smp.o obj-$(CONFIG_IBMVIO) += vio.o obj-$(CONFIG_XICS) += xics.o diff --git a/arch/powerpc/platforms/pseries/firmware.c b/arch/powerpc/platforms/pseries/firmware.c new file mode 100644 index 00000000000000..989f4bc136cb1c --- /dev/null +++ b/arch/powerpc/platforms/pseries/firmware.c @@ -0,0 +1,103 @@ +/* + * pSeries firmware setup code. + * + * Portions from arch/powerpc/platforms/pseries/setup.c: + * Copyright (C) 1995 Linus Torvalds + * Adapted from 'alpha' version by Gary Thomas + * Modified by Cort Dougan (cort@cs.nmt.edu) + * Modified by PPC64 Team, IBM Corp + * + * Portions from arch/powerpc/kernel/firmware.c + * Copyright (C) 2001 Ben. Herrenschmidt (benh@kernel.crashing.org) + * Modifications for ppc64: + * Copyright (C) 2003 Dave Engebretsen <engebret@us.ibm.com> + * Copyright (C) 2005 Stephen Rothwell, IBM Corporation + * + * Copyright 2006 IBM Corporation. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#undef DEBUG + +#include <asm/firmware.h> +#include <asm/prom.h> + +#ifdef DEBUG +#define DBG(fmt...) udbg_printf(fmt) +#else +#define DBG(fmt...) +#endif + +typedef struct { + unsigned long val; + char * name; +} firmware_feature_t; + +static __initdata firmware_feature_t +firmware_features_table[FIRMWARE_MAX_FEATURES] = { + {FW_FEATURE_PFT, "hcall-pft"}, + {FW_FEATURE_TCE, "hcall-tce"}, + {FW_FEATURE_SPRG0, "hcall-sprg0"}, + {FW_FEATURE_DABR, "hcall-dabr"}, + {FW_FEATURE_COPY, "hcall-copy"}, + {FW_FEATURE_ASR, "hcall-asr"}, + {FW_FEATURE_DEBUG, "hcall-debug"}, + {FW_FEATURE_PERF, "hcall-perf"}, + {FW_FEATURE_DUMP, "hcall-dump"}, + {FW_FEATURE_INTERRUPT, "hcall-interrupt"}, + {FW_FEATURE_MIGRATE, "hcall-migrate"}, + {FW_FEATURE_PERFMON, "hcall-perfmon"}, + {FW_FEATURE_CRQ, "hcall-crq"}, + {FW_FEATURE_VIO, "hcall-vio"}, + {FW_FEATURE_RDMA, "hcall-rdma"}, + {FW_FEATURE_LLAN, "hcall-lLAN"}, + {FW_FEATURE_BULK, "hcall-bulk"}, + {FW_FEATURE_XDABR, "hcall-xdabr"}, + {FW_FEATURE_MULTITCE, "hcall-multi-tce"}, + {FW_FEATURE_SPLPAR, "hcall-splpar"}, +}; + +/* Build up the firmware features bitmask using the contents of + * device-tree/ibm,hypertas-functions. Ultimately this functionality may + * be moved into prom.c prom_init(). + */ +void __init fw_feature_init(void) +{ + struct device_node *dn; + char *hypertas, *s; + int len, i; + + DBG(" -> fw_feature_init()\n"); + + dn = of_find_node_by_path("/rtas"); + if (dn == NULL) { + printk(KERN_ERR "WARNING! Cannot find RTAS in device-tree!\n"); + goto out; + } + + hypertas = get_property(dn, "ibm,hypertas-functions", &len); + if (hypertas == NULL) + goto out; + + for (s = hypertas; s < hypertas + len; s += strlen(s) + 1) { + for (i = 0; i < FIRMWARE_MAX_FEATURES; i++) { + /* check value against table of strings */ + if (!firmware_features_table[i].name || + strcmp(firmware_features_table[i].name, s)) + continue; + + /* we have a match */ + ppc64_firmware_features |= + firmware_features_table[i].val; + break; + } + } + +out: + of_node_put(dn); + DBG(" <- fw_feature_init()\n"); +} diff --git a/arch/powerpc/platforms/pseries/firmware.h b/arch/powerpc/platforms/pseries/firmware.h new file mode 100644 index 00000000000000..714f56f5536216 --- /dev/null +++ b/arch/powerpc/platforms/pseries/firmware.h @@ -0,0 +1,17 @@ +/* + * Copyright 2006 IBM Corporation. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#ifndef _PSERIES_FIRMWARE_H +#define _PSERIES_FIRMWARE_H + +#include <asm/firmware.h> + +extern void __init fw_feature_init(void); + +#endif /* _PSERIES_FIRMWARE_H */ diff --git a/arch/powerpc/platforms/pseries/hvCall.S b/arch/powerpc/platforms/pseries/hvCall.S index 176e8da764669c..db7c19fe92972c 100644 --- a/arch/powerpc/platforms/pseries/hvCall.S +++ b/arch/powerpc/platforms/pseries/hvCall.S @@ -1,6 +1,4 @@ /* - * arch/ppc64/kernel/pSeries_hvCall.S - * * This file contains the generic code to perform a call to the * pSeries LPAR hypervisor. * NOTE: this file will go away when we move to inline this work. diff --git a/arch/powerpc/platforms/pseries/iommu.c b/arch/powerpc/platforms/pseries/iommu.c index 48cfbfc43f9921..57930e23cc7460 100644 --- a/arch/powerpc/platforms/pseries/iommu.c +++ b/arch/powerpc/platforms/pseries/iommu.c @@ -1,6 +1,4 @@ /* - * arch/ppc64/kernel/pSeries_iommu.c - * * Copyright (C) 2001 Mike Corrigan & Dave Engebretsen, IBM Corporation * * Rewrite, cleanup: diff --git a/arch/powerpc/platforms/pseries/pci.c b/arch/powerpc/platforms/pseries/pci.c index 999a9620b5ce0f..946ad59e335204 100644 --- a/arch/powerpc/platforms/pseries/pci.c +++ b/arch/powerpc/platforms/pseries/pci.c @@ -1,6 +1,4 @@ /* - * arch/ppc64/kernel/pSeries_pci.c - * * Copyright (C) 2001 Dave Engebretsen, IBM Corporation * Copyright (C) 2003 Anton Blanchard <anton@au.ibm.com>, IBM * diff --git a/arch/powerpc/platforms/pseries/setup.c b/arch/powerpc/platforms/pseries/setup.c index 9edeca83f43463..b5996a7060f43d 100644 --- a/arch/powerpc/platforms/pseries/setup.c +++ b/arch/powerpc/platforms/pseries/setup.c @@ -60,7 +60,6 @@ #include <asm/time.h> #include <asm/nvram.h> #include "xics.h" -#include <asm/firmware.h> #include <asm/pmc.h> #include <asm/mpic.h> #include <asm/ppc-pci.h> @@ -70,6 +69,7 @@ #include "plpar_wrappers.h" #include "ras.h" +#include "firmware.h" #ifdef DEBUG #define DBG(fmt...) udbg_printf(fmt) @@ -262,53 +262,6 @@ static int __init pSeries_init_panel(void) } arch_initcall(pSeries_init_panel); - -/* Build up the ppc64_firmware_features bitmask field - * using contents of device-tree/ibm,hypertas-functions. - * Ultimately this functionality may be moved into prom.c prom_init(). - */ -static void __init fw_feature_init(void) -{ - struct device_node * dn; - char * hypertas; - unsigned int len; - - DBG(" -> fw_feature_init()\n"); - - ppc64_firmware_features = 0; - dn = of_find_node_by_path("/rtas"); - if (dn == NULL) { - printk(KERN_ERR "WARNING ! Cannot find RTAS in device-tree !\n"); - goto no_rtas; - } - - hypertas = get_property(dn, "ibm,hypertas-functions", &len); - if (hypertas) { - while (len > 0){ - int i, hypertas_len; - /* check value against table of strings */ - for(i=0; i < FIRMWARE_MAX_FEATURES ;i++) { - if ((firmware_features_table[i].name) && - (strcmp(firmware_features_table[i].name,hypertas))==0) { - /* we have a match */ - ppc64_firmware_features |= - (firmware_features_table[i].val); - break; - } - } - hypertas_len = strlen(hypertas); - len -= hypertas_len +1; - hypertas+= hypertas_len +1; - } - } - - of_node_put(dn); -no_rtas: - - DBG(" <- fw_feature_init()\n"); -} - - static void __init pSeries_discover_pic(void) { struct device_node *np; diff --git a/arch/powerpc/sysdev/dart_iommu.c b/arch/powerpc/sysdev/dart_iommu.c index 6298264efe3611..61d317428610ab 100644 --- a/arch/powerpc/sysdev/dart_iommu.c +++ b/arch/powerpc/sysdev/dart_iommu.c @@ -194,8 +194,6 @@ static int dart_init(struct device_node *dart_node) * prefetching into invalid pages and corrupting data */ tmp = lmb_alloc(DART_PAGE_SIZE, DART_PAGE_SIZE); - if (!tmp) - panic("DART: Cannot allocate spare page!"); dart_emptyval = DARTMAP_VALID | ((tmp >> DART_PAGE_SHIFT) & DARTMAP_RPNMASK); diff --git a/arch/powerpc/sysdev/dcr.S b/arch/powerpc/sysdev/dcr.S index 895f10243a43a9..2078f39e2f179a 100644 --- a/arch/powerpc/sysdev/dcr.S +++ b/arch/powerpc/sysdev/dcr.S @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/dcr.S - * * "Indirect" DCR access * * Copyright (c) 2004 Eugene Surovegin <ebs@ebshome.net> diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c index 064c9de4773216..ceb584682fa30f 100644 --- a/arch/powerpc/sysdev/fsl_soc.c +++ b/arch/powerpc/sysdev/fsl_soc.c @@ -40,7 +40,7 @@ phys_addr_t get_immrbase(void) return immrbase; soc = of_find_node_by_type(NULL, "soc"); - if (soc != 0) { + if (soc) { unsigned int size; void *prop = get_property(soc, "reg", &size); immrbase = of_translate_address(soc, prop); @@ -49,21 +49,20 @@ phys_addr_t get_immrbase(void) return immrbase; } -EXPORT_SYMBOL(get_immrbase); -static const char * gfar_tx_intr = "tx"; -static const char * gfar_rx_intr = "rx"; -static const char * gfar_err_intr = "error"; +EXPORT_SYMBOL(get_immrbase); -static int __init gfar_of_init(void) +static int __init gfar_mdio_of_init(void) { struct device_node *np; unsigned int i; - struct platform_device *mdio_dev, *gfar_dev; + struct platform_device *mdio_dev; struct resource res; int ret; - for (np = NULL, i = 0; (np = of_find_compatible_node(np, "mdio", "gianfar")) != NULL; i++) { + for (np = NULL, i = 0; + (np = of_find_compatible_node(np, "mdio", "gianfar")) != NULL; + i++) { int k; struct device_node *child = NULL; struct gianfar_mdio_data mdio_data; @@ -73,12 +72,14 @@ static int __init gfar_of_init(void) ret = of_address_to_resource(np, 0, &res); if (ret) - goto mdio_err; + goto err; - mdio_dev = platform_device_register_simple("fsl-gianfar_mdio", res.start, &res, 1); + mdio_dev = + platform_device_register_simple("fsl-gianfar_mdio", + res.start, &res, 1); if (IS_ERR(mdio_dev)) { ret = PTR_ERR(mdio_dev); - goto mdio_err; + goto err; } for (k = 0; k < 32; k++) @@ -86,17 +87,44 @@ static int __init gfar_of_init(void) while ((child = of_get_next_child(np, child)) != NULL) { if (child->n_intrs) { - u32 *id = (u32 *) get_property(child, "reg", NULL); + u32 *id = + (u32 *) get_property(child, "reg", NULL); mdio_data.irq[*id] = child->intrs[0].line; } } - ret = platform_device_add_data(mdio_dev, &mdio_data, sizeof(struct gianfar_mdio_data)); + ret = + platform_device_add_data(mdio_dev, &mdio_data, + sizeof(struct gianfar_mdio_data)); if (ret) - goto mdio_unreg; + goto unreg; } - for (np = NULL, i = 0; (np = of_find_compatible_node(np, "network", "gianfar")) != NULL; i++) { + return 0; + +unreg: + platform_device_unregister(mdio_dev); +err: + return ret; +} + +arch_initcall(gfar_mdio_of_init); + +static const char *gfar_tx_intr = "tx"; +static const char *gfar_rx_intr = "rx"; +static const char *gfar_err_intr = "error"; + +static int __init gfar_of_init(void) +{ + struct device_node *np; + unsigned int i; + struct platform_device *gfar_dev; + struct resource res; + int ret; + + for (np = NULL, i = 0; + (np = of_find_compatible_node(np, "network", "gianfar")) != NULL; + i++) { struct resource r[4]; struct device_node *phy, *mdio; struct gianfar_platform_data gfar_data; @@ -110,7 +138,7 @@ static int __init gfar_of_init(void) ret = of_address_to_resource(np, 0, &r[0]); if (ret) - goto gfar_err; + goto err; r[1].start = np->intrs[0].line; r[1].end = np->intrs[0].line; @@ -133,11 +161,13 @@ static int __init gfar_of_init(void) r[3].flags = IORESOURCE_IRQ; } - gfar_dev = platform_device_register_simple("fsl-gianfar", i, &r[0], np->n_intrs + 1); + gfar_dev = + platform_device_register_simple("fsl-gianfar", i, &r[0], + np->n_intrs + 1); if (IS_ERR(gfar_dev)) { ret = PTR_ERR(gfar_dev); - goto gfar_err; + goto err; } mac_addr = get_property(np, "address", NULL); @@ -145,26 +175,26 @@ static int __init gfar_of_init(void) if (model && !strcasecmp(model, "TSEC")) gfar_data.device_flags = - FSL_GIANFAR_DEV_HAS_GIGABIT | - FSL_GIANFAR_DEV_HAS_COALESCE | - FSL_GIANFAR_DEV_HAS_RMON | - FSL_GIANFAR_DEV_HAS_MULTI_INTR; + FSL_GIANFAR_DEV_HAS_GIGABIT | + FSL_GIANFAR_DEV_HAS_COALESCE | + FSL_GIANFAR_DEV_HAS_RMON | + FSL_GIANFAR_DEV_HAS_MULTI_INTR; if (model && !strcasecmp(model, "eTSEC")) gfar_data.device_flags = - FSL_GIANFAR_DEV_HAS_GIGABIT | - FSL_GIANFAR_DEV_HAS_COALESCE | - FSL_GIANFAR_DEV_HAS_RMON | - FSL_GIANFAR_DEV_HAS_MULTI_INTR | - FSL_GIANFAR_DEV_HAS_CSUM | - FSL_GIANFAR_DEV_HAS_VLAN | - FSL_GIANFAR_DEV_HAS_EXTENDED_HASH; + FSL_GIANFAR_DEV_HAS_GIGABIT | + FSL_GIANFAR_DEV_HAS_COALESCE | + FSL_GIANFAR_DEV_HAS_RMON | + FSL_GIANFAR_DEV_HAS_MULTI_INTR | + FSL_GIANFAR_DEV_HAS_CSUM | + FSL_GIANFAR_DEV_HAS_VLAN | + FSL_GIANFAR_DEV_HAS_EXTENDED_HASH; ph = (phandle *) get_property(np, "phy-handle", NULL); phy = of_find_node_by_phandle(*ph); if (phy == NULL) { ret = -ENODEV; - goto gfar_unreg; + goto unreg; } mdio = of_get_parent(phy); @@ -174,7 +204,7 @@ static int __init gfar_of_init(void) if (ret) { of_node_put(phy); of_node_put(mdio); - goto gfar_unreg; + goto unreg; } gfar_data.phy_id = *id; @@ -183,23 +213,22 @@ static int __init gfar_of_init(void) of_node_put(phy); of_node_put(mdio); - ret = platform_device_add_data(gfar_dev, &gfar_data, sizeof(struct gianfar_platform_data)); + ret = + platform_device_add_data(gfar_dev, &gfar_data, + sizeof(struct + gianfar_platform_data)); if (ret) - goto gfar_unreg; + goto unreg; } return 0; -mdio_unreg: - platform_device_unregister(mdio_dev); -mdio_err: - return ret; - -gfar_unreg: +unreg: platform_device_unregister(gfar_dev); -gfar_err: +err: return ret; } + arch_initcall(gfar_of_init); static int __init fsl_i2c_of_init(void) @@ -209,17 +238,19 @@ static int __init fsl_i2c_of_init(void) struct platform_device *i2c_dev; int ret; - for (np = NULL, i = 0; (np = of_find_compatible_node(np, "i2c", "fsl-i2c")) != NULL; i++) { + for (np = NULL, i = 0; + (np = of_find_compatible_node(np, "i2c", "fsl-i2c")) != NULL; + i++) { struct resource r[2]; struct fsl_i2c_platform_data i2c_data; - unsigned char * flags = NULL; + unsigned char *flags = NULL; memset(&r, 0, sizeof(r)); memset(&i2c_data, 0, sizeof(i2c_data)); ret = of_address_to_resource(np, 0, &r[0]); if (ret) - goto i2c_err; + goto err; r[1].start = np->intrs[0].line; r[1].end = np->intrs[0].line; @@ -228,7 +259,7 @@ static int __init fsl_i2c_of_init(void) i2c_dev = platform_device_register_simple("fsl-i2c", i, r, 2); if (IS_ERR(i2c_dev)) { ret = PTR_ERR(i2c_dev); - goto i2c_err; + goto err; } i2c_data.device_flags = 0; @@ -240,18 +271,22 @@ static int __init fsl_i2c_of_init(void) if (flags) i2c_data.device_flags |= FSL_I2C_DEV_CLOCK_5200; - ret = platform_device_add_data(i2c_dev, &i2c_data, sizeof(struct fsl_i2c_platform_data)); + ret = + platform_device_add_data(i2c_dev, &i2c_data, + sizeof(struct + fsl_i2c_platform_data)); if (ret) - goto i2c_unreg; + goto unreg; } return 0; -i2c_unreg: +unreg: platform_device_unregister(i2c_dev); -i2c_err: +err: return ret; } + arch_initcall(fsl_i2c_of_init); #ifdef CONFIG_PPC_83xx @@ -267,51 +302,192 @@ static int __init mpc83xx_wdt_init(void) if (!np) { ret = -ENODEV; - goto mpc83xx_wdt_nodev; + goto nodev; } soc = of_find_node_by_type(NULL, "soc"); if (!soc) { ret = -ENODEV; - goto mpc83xx_wdt_nosoc; + goto nosoc; } freq = (unsigned int *)get_property(soc, "bus-frequency", NULL); if (!freq) { ret = -ENODEV; - goto mpc83xx_wdt_err; + goto err; } memset(&r, 0, sizeof(r)); ret = of_address_to_resource(np, 0, &r); if (ret) - goto mpc83xx_wdt_err; + goto err; dev = platform_device_register_simple("mpc83xx_wdt", 0, &r, 1); if (IS_ERR(dev)) { ret = PTR_ERR(dev); - goto mpc83xx_wdt_err; + goto err; } ret = platform_device_add_data(dev, freq, sizeof(int)); if (ret) - goto mpc83xx_wdt_unreg; + goto unreg; of_node_put(soc); of_node_put(np); return 0; -mpc83xx_wdt_unreg: +unreg: platform_device_unregister(dev); -mpc83xx_wdt_err: +err: of_node_put(soc); -mpc83xx_wdt_nosoc: +nosoc: of_node_put(np); -mpc83xx_wdt_nodev: +nodev: return ret; } + arch_initcall(mpc83xx_wdt_init); #endif + +static enum fsl_usb2_phy_modes determine_usb_phy(char * phy_type) +{ + if (!phy_type) + return FSL_USB2_PHY_NONE; + if (!strcasecmp(phy_type, "ulpi")) + return FSL_USB2_PHY_ULPI; + if (!strcasecmp(phy_type, "utmi")) + return FSL_USB2_PHY_UTMI; + if (!strcasecmp(phy_type, "utmi_wide")) + return FSL_USB2_PHY_UTMI_WIDE; + if (!strcasecmp(phy_type, "serial")) + return FSL_USB2_PHY_SERIAL; + + return FSL_USB2_PHY_NONE; +} + +static int __init fsl_usb_of_init(void) +{ + struct device_node *np; + unsigned int i; + struct platform_device *usb_dev; + int ret; + + for (np = NULL, i = 0; + (np = of_find_compatible_node(np, "usb", "fsl-usb2-mph")) != NULL; + i++) { + struct resource r[2]; + struct fsl_usb2_platform_data usb_data; + unsigned char *prop = NULL; + + memset(&r, 0, sizeof(r)); + memset(&usb_data, 0, sizeof(usb_data)); + + ret = of_address_to_resource(np, 0, &r[0]); + if (ret) + goto err; + + r[1].start = np->intrs[0].line; + r[1].end = np->intrs[0].line; + r[1].flags = IORESOURCE_IRQ; + + usb_dev = + platform_device_register_simple("fsl-usb2-mph", i, r, 2); + if (IS_ERR(usb_dev)) { + ret = PTR_ERR(usb_dev); + goto err; + } + + usb_dev->dev.coherent_dma_mask = 0xffffffffUL; + usb_dev->dev.dma_mask = &usb_dev->dev.coherent_dma_mask; + + usb_data.operating_mode = FSL_USB2_MPH_HOST; + + prop = get_property(np, "port0", NULL); + if (prop) + usb_data.port_enables |= FSL_USB2_PORT0_ENABLED; + + prop = get_property(np, "port1", NULL); + if (prop) + usb_data.port_enables |= FSL_USB2_PORT1_ENABLED; + + prop = get_property(np, "phy_type", NULL); + usb_data.phy_mode = determine_usb_phy(prop); + + ret = + platform_device_add_data(usb_dev, &usb_data, + sizeof(struct + fsl_usb2_platform_data)); + if (ret) + goto unreg; + } + + return 0; + +unreg: + platform_device_unregister(usb_dev); +err: + return ret; +} + +arch_initcall(fsl_usb_of_init); + +static int __init fsl_usb_dr_of_init(void) +{ + struct device_node *np; + unsigned int i; + struct platform_device *usb_dev; + int ret; + + for (np = NULL, i = 0; + (np = of_find_compatible_node(np, "usb", "fsl-usb2-dr")) != NULL; + i++) { + struct resource r[2]; + struct fsl_usb2_platform_data usb_data; + unsigned char *prop = NULL; + + memset(&r, 0, sizeof(r)); + memset(&usb_data, 0, sizeof(usb_data)); + + ret = of_address_to_resource(np, 0, &r[0]); + if (ret) + goto err; + + r[1].start = np->intrs[0].line; + r[1].end = np->intrs[0].line; + r[1].flags = IORESOURCE_IRQ; + + usb_dev = + platform_device_register_simple("fsl-usb2-dr", i, r, 2); + if (IS_ERR(usb_dev)) { + ret = PTR_ERR(usb_dev); + goto err; + } + + usb_dev->dev.coherent_dma_mask = 0xffffffffUL; + usb_dev->dev.dma_mask = &usb_dev->dev.coherent_dma_mask; + + usb_data.operating_mode = FSL_USB2_DR_HOST; + + prop = get_property(np, "phy_type", NULL); + usb_data.phy_mode = determine_usb_phy(prop); + + ret = + platform_device_add_data(usb_dev, &usb_data, + sizeof(struct + fsl_usb2_platform_data)); + if (ret) + goto unreg; + } + + return 0; + +unreg: + platform_device_unregister(usb_dev); +err: + return ret; +} + +arch_initcall(fsl_usb_dr_of_init); diff --git a/arch/powerpc/sysdev/ipic.h b/arch/powerpc/sysdev/ipic.h index a7ce7da8785c4c..a60c9d18bb7f2e 100644 --- a/arch/powerpc/sysdev/ipic.h +++ b/arch/powerpc/sysdev/ipic.h @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/ipic.h - * * IPIC private definitions and structure. * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/4xx_io/serial_sicc.c b/arch/ppc/4xx_io/serial_sicc.c index 8ace2a1f3b488f..4dc6aa2abfc1dd 100644 --- a/arch/ppc/4xx_io/serial_sicc.c +++ b/arch/ppc/4xx_io/serial_sicc.c @@ -1,6 +1,4 @@ /* - * arch/ppc/4xx_io/serial_sicc.c - * * Driver for IBM STB3xxx SICC serial port * * Based on drivers/char/serial_amba.c, by ARM Ltd. diff --git a/arch/ppc/8xx_io/commproc.c b/arch/ppc/8xx_io/commproc.c index 579cd40258b977..12b84ca51327f5 100644 --- a/arch/ppc/8xx_io/commproc.c +++ b/arch/ppc/8xx_io/commproc.c @@ -73,7 +73,7 @@ cpm_mask_irq(unsigned int irq) { int cpm_vec = irq - CPM_IRQ_OFFSET; - out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr, in_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr) & ~(1 << cpm_vec)); + clrbits32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr, (1 << cpm_vec)); } static void @@ -81,7 +81,7 @@ cpm_unmask_irq(unsigned int irq) { int cpm_vec = irq - CPM_IRQ_OFFSET; - out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr, in_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr) | (1 << cpm_vec)); + setbits32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr, (1 << cpm_vec)); } static void @@ -198,7 +198,7 @@ cpm_interrupt_init(void) if (setup_irq(CPM_IRQ_OFFSET + CPMVEC_ERROR, &cpm_error_irqaction)) panic("Could not allocate CPM error IRQ!"); - out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr, in_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr) | CICR_IEN); + setbits32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr, CICR_IEN); } /* diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig index 11899f06bf06b4..54a0a9bb12ddd1 100644 --- a/arch/ppc/Kconfig +++ b/arch/ppc/Kconfig @@ -481,6 +481,53 @@ config WINCEPT endchoice +menu "Freescale Ethernet driver platform-specific options" + depends on FS_ENET + + config MPC8xx_SECOND_ETH + bool "Second Ethernet channel" + depends on (MPC885ADS || MPC86XADS) + default y + help + This enables support for second Ethernet on MPC885ADS and MPC86xADS boards. + The latter will use SCC1, for 885ADS you can select it below. + + choice + prompt "Second Ethernet channel" + depends on MPC8xx_SECOND_ETH + default MPC8xx_SECOND_ETH_FEC2 + + config MPC8xx_SECOND_ETH_FEC2 + bool "FEC2" + depends on MPC885ADS + help + Enable FEC2 to serve as 2-nd Ethernet channel. Note that SMC2 + (often 2-nd UART) will not work if this is enabled. + + config MPC8xx_SECOND_ETH_SCC1 + bool "SCC1" + depends on MPC86XADS + select MPC8xx_SCC_ENET_FIXED + help + Enable SCC1 to serve as 2-nd Ethernet channel. Note that SMC1 + (often 1-nd UART) will not work if this is enabled. + + config MPC8xx_SECOND_ETH_SCC3 + bool "SCC3" + depends on MPC885ADS + help + Enable SCC3 to serve as 2-nd Ethernet channel. Note that SMC1 + (often 1-nd UART) will not work if this is enabled. + + endchoice + + config MPC8xx_SCC_ENET_FIXED + depends on MPC8xx_SECOND_ETH_SCC + default n + bool "Use fixed MII-less mode for SCC Ethernet" + +endmenu + choice prompt "Machine Type" depends on 6xx || POWER3 diff --git a/arch/ppc/Kconfig.debug b/arch/ppc/Kconfig.debug index 61653cb60c4e3f..8cc75abf3d834f 100644 --- a/arch/ppc/Kconfig.debug +++ b/arch/ppc/Kconfig.debug @@ -67,7 +67,7 @@ config SERIAL_TEXT_DEBUG config PPC_OCP bool - depends on IBM_OCP || XILINX_OCP + depends on IBM_OCP default y endmenu diff --git a/arch/ppc/amiga/amiints.c b/arch/ppc/amiga/amiints.c index 5f35cf3986f768..b2bba052ab934a 100644 --- a/arch/ppc/amiga/amiints.c +++ b/arch/ppc/amiga/amiints.c @@ -1,5 +1,5 @@ /* - * arch/ppc/amiga/amiints.c -- Amiga Linux interrupt handling code + * Amiga Linux interrupt handling code * * This file is subject to the terms and conditions of the GNU General Public * License. See the file COPYING in the main directory of this archive diff --git a/arch/ppc/amiga/bootinfo.c b/arch/ppc/amiga/bootinfo.c index e2e965661d03f1..efd869a3ed9be3 100644 --- a/arch/ppc/amiga/bootinfo.c +++ b/arch/ppc/amiga/bootinfo.c @@ -1,6 +1,4 @@ /* - * arch/ppc/amiga/bootinfo.c - * * Extracted from arch/m68k/kernel/setup.c. * Should be properly generalized and put somewhere else. * Jesper diff --git a/arch/ppc/amiga/cia.c b/arch/ppc/amiga/cia.c index 4431c58f611a95..9558f2f40e6467 100644 --- a/arch/ppc/amiga/cia.c +++ b/arch/ppc/amiga/cia.c @@ -1,6 +1,4 @@ /* - * arch/ppc/amiga/cia.c - CIA support - * * Copyright (C) 1996 Roman Zippel * * The concept of some functions bases on the original Amiga OS function diff --git a/arch/ppc/amiga/config.c b/arch/ppc/amiga/config.c index 60e2da1c92c07a..bbe47c9bd707cf 100644 --- a/arch/ppc/amiga/config.c +++ b/arch/ppc/amiga/config.c @@ -1,8 +1,6 @@ #define m68k_debug_device debug_device /* - * arch/ppc/amiga/config.c - * * Copyright (C) 1993 Hamish Macdonald * * This file is subject to the terms and conditions of the GNU General Public diff --git a/arch/ppc/amiga/ints.c b/arch/ppc/amiga/ints.c index 5d318e498f06f7..083a1746219091 100644 --- a/arch/ppc/amiga/ints.c +++ b/arch/ppc/amiga/ints.c @@ -1,6 +1,4 @@ /* - * arch/ppc/amiga/ints.c - * * Linux/m68k general interrupt handling code from arch/m68k/kernel/ints.c * Needed to drive the m68k emulating IRQ hardware on the PowerUp boards. */ diff --git a/arch/ppc/boot/Makefile b/arch/ppc/boot/Makefile index efd8ce515d5fb3..f565699a9fe0d6 100644 --- a/arch/ppc/boot/Makefile +++ b/arch/ppc/boot/Makefile @@ -1,6 +1,3 @@ -# -# arch/ppc/boot/Makefile -# # This file is subject to the terms and conditions of the GNU General Public # License. See the file "COPYING" in the main directory of this archive # for more details. diff --git a/arch/ppc/boot/common/Makefile b/arch/ppc/boot/common/Makefile index f88d647d5dd4cd..a2e85e3beb8804 100644 --- a/arch/ppc/boot/common/Makefile +++ b/arch/ppc/boot/common/Makefile @@ -1,6 +1,3 @@ -# -# arch/ppc/boot/common/Makefile -# # This file is subject to the terms and conditions of the GNU General Public # License. See the file "COPYING" in the main directory of this archive # for more details. diff --git a/arch/ppc/boot/common/bootinfo.c b/arch/ppc/boot/common/bootinfo.c index 9c6e528940e90f..f4dc9b9fab9c1d 100644 --- a/arch/ppc/boot/common/bootinfo.c +++ b/arch/ppc/boot/common/bootinfo.c @@ -1,6 +1,4 @@ /* - * arch/ppc/common/bootinfo.c - * * General bootinfo record utilities * Author: Randy Vinson <rvinson@mvista.com> * diff --git a/arch/ppc/boot/common/misc-common.c b/arch/ppc/boot/common/misc-common.c index e79e6b3f276ec8..073830a8559ac5 100644 --- a/arch/ppc/boot/common/misc-common.c +++ b/arch/ppc/boot/common/misc-common.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/common/misc-common.c - * * Misc. bootloader code (almost) all platforms can use * * Author: Johnnie Peters <jpeters@mvista.com> diff --git a/arch/ppc/boot/common/ns16550.c b/arch/ppc/boot/common/ns16550.c index 26818bbb6cfff6..4f00c93ac87024 100644 --- a/arch/ppc/boot/common/ns16550.c +++ b/arch/ppc/boot/common/ns16550.c @@ -8,6 +8,9 @@ #include <linux/serial_reg.h> #include <asm/serial.h> +#if defined(CONFIG_XILINX_VIRTEX) +#include <platforms/4xx/xparameters/xparameters.h> +#endif #include "nonstdio.h" #include "serial.h" diff --git a/arch/ppc/boot/common/serial_stub.c b/arch/ppc/boot/common/serial_stub.c index 03dfaa01fa63de..5cc9ae66a8ba44 100644 --- a/arch/ppc/boot/common/serial_stub.c +++ b/arch/ppc/boot/common/serial_stub.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/common/serial_stub.c - * * This is a few stub routines to make the boot code cleaner looking when * there is no serial port support doesn't need to be closed, for example. * diff --git a/arch/ppc/boot/common/util.S b/arch/ppc/boot/common/util.S index 368ec035e6cd98..0c5e43c4ae06c3 100644 --- a/arch/ppc/boot/common/util.S +++ b/arch/ppc/boot/common/util.S @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/common/util.S - * * Useful bootup functions, which are more easily done in asm than C. * * NOTE: Be very very careful about the registers you use here. diff --git a/arch/ppc/boot/include/mpc10x.h b/arch/ppc/boot/include/mpc10x.h index 6cd40ecabc7482..6e5d540d8d3e52 100644 --- a/arch/ppc/boot/include/mpc10x.h +++ b/arch/ppc/boot/include/mpc10x.h @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/include/mpc10.h - * * Common defines for the Motorola SPS MPC106/8240/107 Host bridge/Mem * ctrl/EPIC/etc. * diff --git a/arch/ppc/boot/simple/Makefile b/arch/ppc/boot/simple/Makefile index 9533f8de238ffc..28be01b99c44b7 100644 --- a/arch/ppc/boot/simple/Makefile +++ b/arch/ppc/boot/simple/Makefile @@ -192,6 +192,7 @@ boot-$(CONFIG_8xx) += embed_config.o boot-$(CONFIG_8260) += embed_config.o boot-$(CONFIG_EP405) += embed_config.o boot-$(CONFIG_XILINX_ML300) += embed_config.o +boot-$(CONFIG_XILINX_ML403) += embed_config.o boot-$(CONFIG_BSEIP) += iic.o boot-$(CONFIG_MBX) += iic.o pci.o qspan_pci.o boot-$(CONFIG_MV64X60) += misc-mv64x60.o diff --git a/arch/ppc/boot/simple/cpc700_memory.c b/arch/ppc/boot/simple/cpc700_memory.c index 8c75cf6c238395..d75420a45a59b8 100644 --- a/arch/ppc/boot/simple/cpc700_memory.c +++ b/arch/ppc/boot/simple/cpc700_memory.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/common/cpc700_memory.c - * * Find memory based upon settings in the CPC700 bridge * * Author: Dan Cox diff --git a/arch/ppc/boot/simple/embed_config.c b/arch/ppc/boot/simple/embed_config.c index 491a691d10ccab..3a51b1062940f5 100644 --- a/arch/ppc/boot/simple/embed_config.c +++ b/arch/ppc/boot/simple/embed_config.c @@ -21,6 +21,9 @@ #ifdef CONFIG_40x #include <asm/io.h> #endif +#ifdef CONFIG_XILINX_VIRTEX +#include <platforms/4xx/xparameters/xparameters.h> +#endif extern unsigned long timebase_period_ns; /* For those boards that don't provide one. @@ -742,7 +745,7 @@ embed_config(bd_t **bdp) } #endif /* WILLOW */ -#ifdef CONFIG_XILINX_ML300 +#if defined(CONFIG_XILINX_ML300) || defined(CONFIG_XILINX_ML403) void embed_config(bd_t ** bdp) { @@ -779,7 +782,7 @@ embed_config(bd_t ** bdp) timebase_period_ns = 1000000000 / bd->bi_tbfreq; /* see bi_tbfreq definition in arch/ppc/platforms/4xx/xilinx_ml300.h */ } -#endif /* CONFIG_XILINX_ML300 */ +#endif /* CONFIG_XILINX_ML300 || CONFIG_XILINX_ML403 */ #ifdef CONFIG_IBM_OPENBIOS /* This could possibly work for all treeboot roms. diff --git a/arch/ppc/boot/simple/head.S b/arch/ppc/boot/simple/head.S index 5e4adc298bf9cd..160da1006ff8f5 100644 --- a/arch/ppc/boot/simple/head.S +++ b/arch/ppc/boot/simple/head.S @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/head.S - * * Initial board bringup code for many different boards. * * Author: Tom Rini @@ -65,6 +63,13 @@ start_: */ #endif +#if defined(CONFIG_XILINX_VIRTEX_4_FX) + /* PPC errata 213: only for Virtex-4 FX */ + mfccr0 0 + oris 0,0,0x50000000@h + mtccr0 0 +#endif + mflr r3 /* Save our actual starting address. */ /* The following functions we call must not modify r3 or r4..... diff --git a/arch/ppc/boot/simple/misc-chestnut.c b/arch/ppc/boot/simple/misc-chestnut.c index 0dce7f3557e4db..b94e142ad89220 100644 --- a/arch/ppc/boot/simple/misc-chestnut.c +++ b/arch/ppc/boot/simple/misc-chestnut.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/misc-chestnut.c - * * Setup for the IBM Chestnut (ibm-750fxgx_eval) * * Author: Mark A. Greer <mgreer@mvista.com> diff --git a/arch/ppc/boot/simple/misc-cpci690.c b/arch/ppc/boot/simple/misc-cpci690.c index 26860300fa090e..8a8614d11a32f0 100644 --- a/arch/ppc/boot/simple/misc-cpci690.c +++ b/arch/ppc/boot/simple/misc-cpci690.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/misc-cpci690.c - * * Add birec data for Force CPCI690 board. * * Author: Mark A. Greer <source@mvista.com> diff --git a/arch/ppc/boot/simple/misc-ev64260.c b/arch/ppc/boot/simple/misc-ev64260.c index 52ece6937a7ab4..2678c224af2237 100644 --- a/arch/ppc/boot/simple/misc-ev64260.c +++ b/arch/ppc/boot/simple/misc-ev64260.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/misc-ev64260.c - * * Host bridge init code for the Marvell/Galileo EV-64260-BP evaluation board * with a GT64260 onboard. * diff --git a/arch/ppc/boot/simple/misc-ev64360.c b/arch/ppc/boot/simple/misc-ev64360.c index cd1ccf2a1582f9..a212b5b988cb0e 100644 --- a/arch/ppc/boot/simple/misc-ev64360.c +++ b/arch/ppc/boot/simple/misc-ev64360.c @@ -1,5 +1,4 @@ /* - * arch/ppc/boot/simple/misc-ev64360.c * Copyright (C) 2005 Lee Nicks <allinux@gmail.com> * * Based on arch/ppc/boot/simple/misc-katana.c from: diff --git a/arch/ppc/boot/simple/misc-katana.c b/arch/ppc/boot/simple/misc-katana.c index ec94a11bacac6d..d97f2ee6f04ec4 100644 --- a/arch/ppc/boot/simple/misc-katana.c +++ b/arch/ppc/boot/simple/misc-katana.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/misc-katana.c - * * Set up MPSC values to bootwrapper can prompt user. * * Author: Mark A. Greer <source@mvista.com> diff --git a/arch/ppc/boot/simple/misc-mv64x60.c b/arch/ppc/boot/simple/misc-mv64x60.c index 258d4599fadc5b..71ff20fd494a6d 100644 --- a/arch/ppc/boot/simple/misc-mv64x60.c +++ b/arch/ppc/boot/simple/misc-mv64x60.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/misc-mv64x60.c - * * Relocate bridge's register base and call board specific routine. * * Author: Mark A. Greer <source@mvista.com> diff --git a/arch/ppc/boot/simple/misc-prep.c b/arch/ppc/boot/simple/misc-prep.c index 75380ac4166971..63def9d13d7013 100644 --- a/arch/ppc/boot/simple/misc-prep.c +++ b/arch/ppc/boot/simple/misc-prep.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/misc-prep.c - * * Maintainer: Tom Rini <trini@kernel.crashing.org> * * In the past: Gary Thomas, Cort Dougan <cort@cs.nmt.edu> diff --git a/arch/ppc/boot/simple/misc-radstone_ppc7d.c b/arch/ppc/boot/simple/misc-radstone_ppc7d.c index 569e0d4feeaf1c..0f302ea9c3d1f3 100644 --- a/arch/ppc/boot/simple/misc-radstone_ppc7d.c +++ b/arch/ppc/boot/simple/misc-radstone_ppc7d.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/misc-radstone_ppc7d.c - * * Misc data for Radstone PPC7D board. * * Author: James Chapman <jchapman@katalix.com> diff --git a/arch/ppc/boot/simple/misc-spruce.c b/arch/ppc/boot/simple/misc-spruce.c index d012c39278fdb6..0cad2f557a1e81 100644 --- a/arch/ppc/boot/simple/misc-spruce.c +++ b/arch/ppc/boot/simple/misc-spruce.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/spruce/misc.c - * * Misc. bootloader code for IBM Spruce reference platform * * Authors: Johnnie Peters <jpeters@mvista.com> diff --git a/arch/ppc/boot/simple/misc.c b/arch/ppc/boot/simple/misc.c index f415d6c62362ca..3d78571ad94529 100644 --- a/arch/ppc/boot/simple/misc.c +++ b/arch/ppc/boot/simple/misc.c @@ -1,6 +1,4 @@ /* - * arch/ppc/simple/misc.c - * * Misc. bootloader code for many machines. This assumes you have are using * a 6xx/7xx/74xx CPU in your machine. This assumes the chunk of memory * below 8MB is free. Finally, it assumes you have a NS16550-style uart for diff --git a/arch/ppc/boot/simple/mpc10x_memory.c b/arch/ppc/boot/simple/mpc10x_memory.c index 20d92a34ceb854..c24290823f7fb1 100644 --- a/arch/ppc/boot/simple/mpc10x_memory.c +++ b/arch/ppc/boot/simple/mpc10x_memory.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/common/mpc10x_common.c - * * A routine to find out how much memory the machine has. * * Based on: diff --git a/arch/ppc/boot/simple/mpc52xx_tty.c b/arch/ppc/boot/simple/mpc52xx_tty.c index 3acc6b7c0727cc..1964493cf3bdc0 100644 --- a/arch/ppc/boot/simple/mpc52xx_tty.c +++ b/arch/ppc/boot/simple/mpc52xx_tty.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/mpc52xx_tty.c - * * Minimal serial functions needed to send messages out a MPC52xx * Programmable Serial Controller (PSC). * diff --git a/arch/ppc/boot/simple/mv64x60_tty.c b/arch/ppc/boot/simple/mv64x60_tty.c index b9c24d4c738bb5..0c52f5c784a2ee 100644 --- a/arch/ppc/boot/simple/mv64x60_tty.c +++ b/arch/ppc/boot/simple/mv64x60_tty.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/mv64x60_tty.c - * * Bootloader version of the embedded MPSC/UART driver for the Marvell 64x60. * Note: Due to a GT64260A erratum, DMA will be used for UART input (via SDMA). * diff --git a/arch/ppc/boot/simple/openbios.c b/arch/ppc/boot/simple/openbios.c index 81f11d8b30a7ad..3f2ed53f793ae8 100644 --- a/arch/ppc/boot/simple/openbios.c +++ b/arch/ppc/boot/simple/openbios.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/openbios.c - * * Copyright (c) 2005 DENX Software Engineering * Stefan Roese <sr@denx.de> * diff --git a/arch/ppc/boot/simple/relocate.S b/arch/ppc/boot/simple/relocate.S index 555a216ccc4926..7efddc507564d6 100644 --- a/arch/ppc/boot/simple/relocate.S +++ b/arch/ppc/boot/simple/relocate.S @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/simple/relocate.S - * * This is the common part of the loader relocation and initialization * process. All of the board/processor specific initialization is * done before we get here. diff --git a/arch/ppc/boot/utils/mkbugboot.c b/arch/ppc/boot/utils/mkbugboot.c index 886122283f39ae..29115e01f60adc 100644 --- a/arch/ppc/boot/utils/mkbugboot.c +++ b/arch/ppc/boot/utils/mkbugboot.c @@ -1,6 +1,4 @@ /* - * arch/ppc/boot/utils/mkbugboot.c - * * Makes a Motorola PPCBUG ROM bootable image which can be flashed * into one of the FLASH banks on a Motorola PowerPlus board. * diff --git a/arch/ppc/configs/ml300_defconfig b/arch/ppc/configs/ml300_defconfig new file mode 100644 index 00000000000000..4a33aca948cc70 --- /dev/null +++ b/arch/ppc/configs/ml300_defconfig @@ -0,0 +1,739 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.16-rc1 +# Wed Jan 18 00:49:20 2006 +# +CONFIG_MMU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_PPC=y +CONFIG_PPC32=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_CLEAN_COMPILE=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +CONFIG_BSD_PROCESS_ACCT=y +CONFIG_BSD_PROCESS_ACCT_V3=y +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_EMBEDDED is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_CC_ALIGN_FUNCTIONS=0 +CONFIG_CC_ALIGN_LABELS=0 +CONFIG_CC_ALIGN_LOOPS=0 +CONFIG_CC_ALIGN_JUMPS=0 +CONFIG_SLAB=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_OBSOLETE_MODPARM=y +CONFIG_MODVERSIONS=y +CONFIG_MODULE_SRCVERSION_ALL=y +CONFIG_KMOD=y + +# +# Block layer +# +CONFIG_LBD=y + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# Processor +# +# CONFIG_6xx is not set +CONFIG_40x=y +# CONFIG_44x is not set +# CONFIG_POWER3 is not set +# CONFIG_8xx is not set +# CONFIG_E200 is not set +# CONFIG_E500 is not set +# CONFIG_MATH_EMULATION is not set +# CONFIG_KEXEC is not set +# CONFIG_CPU_FREQ is not set +CONFIG_4xx=y +# CONFIG_WANT_EARLY_SERIAL is not set + +# +# IBM 4xx options +# +# CONFIG_BUBINGA is not set +# CONFIG_CPCI405 is not set +# CONFIG_EP405 is not set +# CONFIG_REDWOOD_5 is not set +# CONFIG_REDWOOD_6 is not set +# CONFIG_SYCAMORE is not set +# CONFIG_WALNUT is not set +CONFIG_XILINX_ML300=y +CONFIG_IBM405_ERR77=y +CONFIG_IBM405_ERR51=y +CONFIG_XILINX_VIRTEX=y +CONFIG_EMBEDDEDBOOT=y +# CONFIG_PPC4xx_DMA is not set +CONFIG_PPC_GEN550=y +CONFIG_UART0_TTYS0=y +# CONFIG_UART0_TTYS1 is not set +CONFIG_NOT_COHERENT_CACHE=y + +# +# Platform options +# +# CONFIG_PC_KEYBOARD is not set +# CONFIG_HIGHMEM is not set +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +CONFIG_CMDLINE_BOOL=y +CONFIG_CMDLINE="console=ttyS0,9600" +# CONFIG_PM is not set +# CONFIG_SOFTWARE_SUSPEND is not set +CONFIG_SECCOMP=y +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +# CONFIG_PPC_I8259 is not set +# CONFIG_PCI is not set +# CONFIG_PCI_DOMAINS is not set + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_HIGHMEM_START=0xfe000000 +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_START=0xff100000 +CONFIG_CONSISTENT_SIZE=0x00200000 +CONFIG_BOOT_LOAD=0x00400000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +# CONFIG_MTD is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=65536 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Macintosh device drivers +# +# CONFIG_WINDFARM is not set + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +CONFIG_TUN=y + +# +# PHY device support +# + +# +# Ethernet (10 or 100Mbit) +# +# CONFIG_NET_ETHERNET is not set +# CONFIG_IBM_EMAC is not set + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# + +# +# Token Ring devices +# + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +# CONFIG_WATCHDOG is not set +# CONFIG_NVRAM is not set +# CONFIG_GEN_RTC is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# Ftape, the floppy tape device driver +# +# CONFIG_AGP is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set + +# +# I2C support +# +# CONFIG_I2C is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +# CONFIG_HWMON is not set +# CONFIG_HWMON_VID is not set + +# +# Misc devices +# + +# +# Multimedia Capabilities Port drivers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Console display driver support +# +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +# CONFIG_USB_ARCH_HAS_HCD is not set +# CONFIG_USB_ARCH_HAS_OHCI is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# InfiniBand support +# + +# +# SN Devices +# + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_RELAYFS_FS is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +# CONFIG_NFS_FS is not set +# CONFIG_NFSD is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +CONFIG_NLS_ASCII=y +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=y + +# +# IBM 40x options +# + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +CONFIG_PRINTK_TIME=y +CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_KERNEL=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_KGDB is not set +CONFIG_XMON=y +# CONFIG_BDI_SWITCH is not set +# CONFIG_SERIAL_TEXT_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Hardware crypto devices +# diff --git a/arch/ppc/configs/ml403_defconfig b/arch/ppc/configs/ml403_defconfig new file mode 100644 index 00000000000000..fafd2516fa5132 --- /dev/null +++ b/arch/ppc/configs/ml403_defconfig @@ -0,0 +1,740 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.16-rc1 +# Wed Jan 18 01:11:41 2006 +# +CONFIG_MMU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_PPC=y +CONFIG_PPC32=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_CLEAN_COMPILE=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +CONFIG_BSD_PROCESS_ACCT=y +CONFIG_BSD_PROCESS_ACCT_V3=y +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_EMBEDDED is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_CC_ALIGN_FUNCTIONS=0 +CONFIG_CC_ALIGN_LABELS=0 +CONFIG_CC_ALIGN_LOOPS=0 +CONFIG_CC_ALIGN_JUMPS=0 +CONFIG_SLAB=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_OBSOLETE_MODPARM=y +CONFIG_MODVERSIONS=y +CONFIG_MODULE_SRCVERSION_ALL=y +CONFIG_KMOD=y + +# +# Block layer +# +CONFIG_LBD=y + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# Processor +# +# CONFIG_6xx is not set +CONFIG_40x=y +# CONFIG_44x is not set +# CONFIG_POWER3 is not set +# CONFIG_8xx is not set +# CONFIG_E200 is not set +# CONFIG_E500 is not set +# CONFIG_MATH_EMULATION is not set +# CONFIG_KEXEC is not set +# CONFIG_CPU_FREQ is not set +CONFIG_4xx=y +# CONFIG_WANT_EARLY_SERIAL is not set + +# +# IBM 4xx options +# +# CONFIG_BUBINGA is not set +# CONFIG_CPCI405 is not set +# CONFIG_EP405 is not set +# CONFIG_REDWOOD_5 is not set +# CONFIG_REDWOOD_6 is not set +# CONFIG_SYCAMORE is not set +# CONFIG_WALNUT is not set +# CONFIG_XILINX_ML300 is not set +CONFIG_XILINX_ML403=y +CONFIG_IBM405_ERR77=y +CONFIG_IBM405_ERR51=y +CONFIG_XILINX_VIRTEX=y +CONFIG_EMBEDDEDBOOT=y +# CONFIG_PPC4xx_DMA is not set +CONFIG_PPC_GEN550=y +CONFIG_UART0_TTYS0=y +# CONFIG_UART0_TTYS1 is not set +CONFIG_NOT_COHERENT_CACHE=y + +# +# Platform options +# +# CONFIG_PC_KEYBOARD is not set +# CONFIG_HIGHMEM is not set +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +CONFIG_CMDLINE_BOOL=y +CONFIG_CMDLINE="console=ttyS0,9600" +# CONFIG_PM is not set +# CONFIG_SOFTWARE_SUSPEND is not set +CONFIG_SECCOMP=y +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +# CONFIG_PPC_I8259 is not set +# CONFIG_PCI is not set +# CONFIG_PCI_DOMAINS is not set + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_HIGHMEM_START=0xfe000000 +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_START=0xff100000 +CONFIG_CONSISTENT_SIZE=0x00200000 +CONFIG_BOOT_LOAD=0x00400000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +CONFIG_PACKET_MMAP=y +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +# CONFIG_MTD is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=65536 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Macintosh device drivers +# +# CONFIG_WINDFARM is not set + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +CONFIG_TUN=y + +# +# PHY device support +# + +# +# Ethernet (10 or 100Mbit) +# +# CONFIG_NET_ETHERNET is not set +# CONFIG_IBM_EMAC is not set + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# + +# +# Token Ring devices +# + +# +# Wireless LAN (non-hamradio) +# +# CONFIG_NET_RADIO is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +# CONFIG_WATCHDOG is not set +# CONFIG_NVRAM is not set +# CONFIG_GEN_RTC is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# Ftape, the floppy tape device driver +# +# CONFIG_AGP is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set + +# +# I2C support +# +# CONFIG_I2C is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +# CONFIG_HWMON is not set +# CONFIG_HWMON_VID is not set + +# +# Misc devices +# + +# +# Multimedia Capabilities Port drivers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Console display driver support +# +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +# CONFIG_USB_ARCH_HAS_HCD is not set +# CONFIG_USB_ARCH_HAS_OHCI is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# InfiniBand support +# + +# +# SN Devices +# + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_RELAYFS_FS is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +# CONFIG_NFS_FS is not set +# CONFIG_NFSD is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +CONFIG_NLS_ASCII=y +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=y + +# +# IBM 40x options +# + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +CONFIG_PRINTK_TIME=y +CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_KERNEL=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_KGDB is not set +CONFIG_XMON=y +# CONFIG_BDI_SWITCH is not set +# CONFIG_SERIAL_TEXT_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Hardware crypto devices +# diff --git a/arch/ppc/kernel/head_44x.S b/arch/ppc/kernel/head_44x.S index 677c571aa27638..0d8b88219d3880 100644 --- a/arch/ppc/kernel/head_44x.S +++ b/arch/ppc/kernel/head_44x.S @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/head_44x.S - * * Kernel execution entry point code. * * Copyright (c) 1995-1996 Gary Thomas <gdt@linuxppc.org> diff --git a/arch/ppc/kernel/head_8xx.S b/arch/ppc/kernel/head_8xx.S index c1e89ad0684da8..ec53c7d65f2b39 100644 --- a/arch/ppc/kernel/head_8xx.S +++ b/arch/ppc/kernel/head_8xx.S @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/except_8xx.S - * * PowerPC version * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) * Rewritten by Cort Dougan (cort@cs.nmt.edu) for PReP diff --git a/arch/ppc/kernel/head_fsl_booke.S b/arch/ppc/kernel/head_fsl_booke.S index 8d60fa99fc4b99..dd86bbed762711 100644 --- a/arch/ppc/kernel/head_fsl_booke.S +++ b/arch/ppc/kernel/head_fsl_booke.S @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/head_fsl_booke.S - * * Kernel execution entry point code. * * Copyright (c) 1995-1996 Gary Thomas <gdt@linuxppc.org> @@ -316,6 +314,7 @@ skpinv: addi r6,r6,1 /* Increment */ */ lis r2,DBCR0_IDM@h mtspr SPRN_DBCR0,r2 + isync /* clear any residual debug events */ li r2,-1 mtspr SPRN_DBSR,r2 @@ -1002,12 +1001,15 @@ _GLOBAL(giveup_fpu) _GLOBAL(abort) li r13,0 mtspr SPRN_DBCR0,r13 /* disable all debug events */ + isync mfmsr r13 ori r13,r13,MSR_DE@l /* Enable Debug Events */ mtmsr r13 + isync mfspr r13,SPRN_DBCR0 lis r13,(DBCR0_IDM|DBCR0_RST_CHIP)@h mtspr SPRN_DBCR0,r13 + isync _GLOBAL(set_context) diff --git a/arch/ppc/kernel/traps.c b/arch/ppc/kernel/traps.c index 6d0a1838d94cc4..1c0d68026abd0b 100644 --- a/arch/ppc/kernel/traps.c +++ b/arch/ppc/kernel/traps.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/traps.c - * * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) * * This program is free software; you can redistribute it and/or diff --git a/arch/ppc/lib/rheap.c b/arch/ppc/lib/rheap.c index 42c5de2c898f28..31e511856dc58b 100644 --- a/arch/ppc/lib/rheap.c +++ b/arch/ppc/lib/rheap.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/rheap.c - * * A Remote Heap. Remote means that we don't touch the memory that the * heap points to. Normal heap implementations use the memory they manage * to place their list. We cannot do that because the memory we manage may diff --git a/arch/ppc/math-emu/math.c b/arch/ppc/math-emu/math.c index b7dff53a71031a..58915347276178 100644 --- a/arch/ppc/math-emu/math.c +++ b/arch/ppc/math-emu/math.c @@ -1,6 +1,4 @@ /* - * arch/ppc/math-emu/math.c - * * Copyright (C) 1999 Eddie C. Dost (ecd@atecom.com) */ diff --git a/arch/ppc/mm/44x_mmu.c b/arch/ppc/mm/44x_mmu.c index 3d79ce281b677f..e0152a9b26e685 100644 --- a/arch/ppc/mm/44x_mmu.c +++ b/arch/ppc/mm/44x_mmu.c @@ -104,7 +104,7 @@ unsigned long __init mmu_mapin_ram(void) /* Determine number of entries necessary to cover lowmem */ pinned_tlbs = (unsigned int) - (_ALIGN(total_lowmem, PPC44x_PIN_SIZE) >> PPC44x_PIN_SHIFT); + (_ALIGN(total_lowmem, PPC_PIN_SIZE) >> PPC44x_PIN_SHIFT); /* Write upper watermark to save location */ tlb_44x_hwater = PPC44x_LOW_SLOT - pinned_tlbs; @@ -112,7 +112,7 @@ unsigned long __init mmu_mapin_ram(void) /* If necessary, set additional pinned TLBs */ if (pinned_tlbs > 1) for (i = (PPC44x_LOW_SLOT-(pinned_tlbs-1)); i < PPC44x_LOW_SLOT; i++) { - unsigned int phys_addr = (PPC44x_LOW_SLOT-i) * PPC44x_PIN_SIZE; + unsigned int phys_addr = (PPC44x_LOW_SLOT-i) * PPC_PIN_SIZE; ppc44x_pin_tlb(i, phys_addr+PAGE_OFFSET, phys_addr); } diff --git a/arch/ppc/mm/fault.c b/arch/ppc/mm/fault.c index ee5e9f25baf98d..0217188ef4656a 100644 --- a/arch/ppc/mm/fault.c +++ b/arch/ppc/mm/fault.c @@ -1,6 +1,4 @@ /* - * arch/ppc/mm/fault.c - * * PowerPC version * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) * diff --git a/arch/ppc/mm/hashtable.S b/arch/ppc/mm/hashtable.S index 3ec87c91343e8f..f09fa88db35acc 100644 --- a/arch/ppc/mm/hashtable.S +++ b/arch/ppc/mm/hashtable.S @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/hashtable.S - * * $Id: hashtable.S,v 1.6 1999/10/08 01:56:15 paulus Exp $ * * PowerPC version diff --git a/arch/ppc/platforms/4xx/Kconfig b/arch/ppc/platforms/4xx/Kconfig index d8837911bbc6a4..174ddbc9758bb1 100644 --- a/arch/ppc/platforms/4xx/Kconfig +++ b/arch/ppc/platforms/4xx/Kconfig @@ -57,6 +57,10 @@ config XILINX_ML300 help This option enables support for the Xilinx ML300 evaluation board. +config XILINX_ML403 + bool "Xilinx-ML403" + help + This option enables support for the Xilinx ML403 evaluation board. endchoice choice @@ -172,11 +176,6 @@ config IBM_OCP depends on ASH || BAMBOO || BUBINGA || CPCI405 || EBONY || EP405 || LUAN || YUCCA || OCOTEA || REDWOOD_5 || REDWOOD_6 || SYCAMORE || WALNUT default y -config XILINX_OCP - bool - depends on XILINX_ML300 - default y - config IBM_EMAC4 bool depends on 440GX || 440SP || 440SPE @@ -208,11 +207,21 @@ config 405GPR depends on SYCAMORE default y -config VIRTEX_II_PRO +config XILINX_VIRTEX_II_PRO bool depends on XILINX_ML300 default y +config XILINX_VIRTEX_4_FX + bool + depends on XILINX_ML403 + default y + +config XILINX_VIRTEX + bool + depends on XILINX_VIRTEX_II_PRO || XILINX_VIRTEX_4_FX + default y + config STB03xxx bool depends on REDWOOD_5 || REDWOOD_6 @@ -220,7 +229,7 @@ config STB03xxx config EMBEDDEDBOOT bool - depends on EP405 || XILINX_ML300 + depends on EP405 || XILINX_ML300 || XILINX_ML403 default y config IBM_OPENBIOS diff --git a/arch/ppc/platforms/4xx/Makefile b/arch/ppc/platforms/4xx/Makefile index c9bb6117095477..a04a0d0a0f5cd6 100644 --- a/arch/ppc/platforms/4xx/Makefile +++ b/arch/ppc/platforms/4xx/Makefile @@ -14,6 +14,7 @@ obj-$(CONFIG_REDWOOD_6) += redwood6.o obj-$(CONFIG_SYCAMORE) += sycamore.o obj-$(CONFIG_WALNUT) += walnut.o obj-$(CONFIG_XILINX_ML300) += xilinx_ml300.o +obj-$(CONFIG_XILINX_ML403) += xilinx_ml403.o obj-$(CONFIG_405GP) += ibm405gp.o obj-$(CONFIG_REDWOOD_5) += ibmstb4.o @@ -26,4 +27,5 @@ obj-$(CONFIG_440SP) += ibm440sp.o obj-$(CONFIG_440SPE) += ppc440spe.o obj-$(CONFIG_405EP) += ibm405ep.o obj-$(CONFIG_405GPR) += ibm405gpr.o -obj-$(CONFIG_VIRTEX_II_PRO) += virtex-ii_pro.o +obj-$(CONFIG_XILINX_VIRTEX) += virtex.o + diff --git a/arch/ppc/platforms/4xx/bamboo.c b/arch/ppc/platforms/4xx/bamboo.c index 0ec53f04933871..b940cfd646c2af 100644 --- a/arch/ppc/platforms/4xx/bamboo.c +++ b/arch/ppc/platforms/4xx/bamboo.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/bamboo.c - * * Bamboo board specific routines * * Wade Farnsworth <wfarnsworth@mvista.com> diff --git a/arch/ppc/platforms/4xx/bamboo.h b/arch/ppc/platforms/4xx/bamboo.h index 5c01928264941a..31c0dd6a26cb73 100644 --- a/arch/ppc/platforms/4xx/bamboo.h +++ b/arch/ppc/platforms/4xx/bamboo.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/bamboo.h - * * Bamboo board definitions * * Wade Farnsworth <wfarnsworth@mvista.com> diff --git a/arch/ppc/platforms/4xx/bubinga.h b/arch/ppc/platforms/4xx/bubinga.h index b5380cfaf5c0ca..606aa9fa5caa80 100644 --- a/arch/ppc/platforms/4xx/bubinga.h +++ b/arch/ppc/platforms/4xx/bubinga.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/bubinga.h - * * Bubinga board definitions * * Copyright (c) 2005 DENX Software Engineering diff --git a/arch/ppc/platforms/4xx/cpci405.c b/arch/ppc/platforms/4xx/cpci405.c index ff966773a0bf3d..6571e39fbe48ce 100644 --- a/arch/ppc/platforms/4xx/cpci405.c +++ b/arch/ppc/platforms/4xx/cpci405.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/cpci405.c - * * Board setup routines for the esd CPCI-405 cPCI Board. * * Author: Stefan Roese diff --git a/arch/ppc/platforms/4xx/ebony.c b/arch/ppc/platforms/4xx/ebony.c index 9a828b623417d3..b4ecb9c798541e 100644 --- a/arch/ppc/platforms/4xx/ebony.c +++ b/arch/ppc/platforms/4xx/ebony.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ebony.c - * * Ebony board specific routines * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/platforms/4xx/ebony.h b/arch/ppc/platforms/4xx/ebony.h index b91ad4272dfe2b..27b2e77c7c8375 100644 --- a/arch/ppc/platforms/4xx/ebony.h +++ b/arch/ppc/platforms/4xx/ebony.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/ebony.h - * * Ebony board definitions * * Matt Porter <mporter@mvista.com> diff --git a/arch/ppc/platforms/4xx/ep405.c b/arch/ppc/platforms/4xx/ep405.c index 26a07cdb30ec8e..6efa91ff9c073e 100644 --- a/arch/ppc/platforms/4xx/ep405.c +++ b/arch/ppc/platforms/4xx/ep405.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ep405.c - * * Embedded Planet 405GP board * http://www.embeddedplanet.com * diff --git a/arch/ppc/platforms/4xx/ep405.h b/arch/ppc/platforms/4xx/ep405.h index ea3eb21338fbb0..9814fc43172554 100644 --- a/arch/ppc/platforms/4xx/ep405.h +++ b/arch/ppc/platforms/4xx/ep405.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ep405.h - * * Embedded Planet 405GP board * http://www.embeddedplanet.com * diff --git a/arch/ppc/platforms/4xx/ibm405ep.c b/arch/ppc/platforms/4xx/ibm405ep.c index 093b28d27a413d..55af769a6e7085 100644 --- a/arch/ppc/platforms/4xx/ibm405ep.c +++ b/arch/ppc/platforms/4xx/ibm405ep.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/ibm405ep.c - * * Support for IBM PPC 405EP processors. * * Author: SAW (IBM), derived from ibmnp405l.c. diff --git a/arch/ppc/platforms/4xx/ibm405ep.h b/arch/ppc/platforms/4xx/ibm405ep.h index e051e3fe8c633a..fe46640de15209 100644 --- a/arch/ppc/platforms/4xx/ibm405ep.h +++ b/arch/ppc/platforms/4xx/ibm405ep.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm405ep.h - * * IBM PPC 405EP processor defines. * * Author: SAW (IBM), derived from ibm405gp.h. diff --git a/arch/ppc/platforms/4xx/ibm405gp.h b/arch/ppc/platforms/4xx/ibm405gp.h index b2b642e81af7c3..eaf0ef57028d20 100644 --- a/arch/ppc/platforms/4xx/ibm405gp.h +++ b/arch/ppc/platforms/4xx/ibm405gp.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm405gp.h - * * Author: Armin Kuster akuster@mvista.com * * 2001 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/4xx/ibm405gpr.c b/arch/ppc/platforms/4xx/ibm405gpr.c index cd0d00d8e8ee51..49da61f6854a08 100644 --- a/arch/ppc/platforms/4xx/ibm405gpr.c +++ b/arch/ppc/platforms/4xx/ibm405gpr.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm405gpr.c - * * Author: Armin Kuster <akuster@mvista.com> * * 2002 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/4xx/ibm405gpr.h b/arch/ppc/platforms/4xx/ibm405gpr.h index 45412fb4368fce..e90c5dde01d35d 100644 --- a/arch/ppc/platforms/4xx/ibm405gpr.h +++ b/arch/ppc/platforms/4xx/ibm405gpr.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm405gpr.h - * * Author: Armin Kuster <akuster@mvista.com> * * 2002 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/4xx/ibm440ep.c b/arch/ppc/platforms/4xx/ibm440ep.c index 65ac0b9c2d05d8..1fed6638c81fe8 100644 --- a/arch/ppc/platforms/4xx/ibm440ep.c +++ b/arch/ppc/platforms/4xx/ibm440ep.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm440ep.c - * * PPC440EP I/O descriptions * * Wade Farnsworth <wfarnsworth@mvista.com> diff --git a/arch/ppc/platforms/4xx/ibm440ep.h b/arch/ppc/platforms/4xx/ibm440ep.h index 97c80b8e3e1087..61717e8a799e96 100644 --- a/arch/ppc/platforms/4xx/ibm440ep.h +++ b/arch/ppc/platforms/4xx/ibm440ep.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm440ep.h - * * PPC440EP definitions * * Wade Farnsworth <wfarnsworth@mvista.com> diff --git a/arch/ppc/platforms/4xx/ibm440gp.c b/arch/ppc/platforms/4xx/ibm440gp.c index d926245e8b3ebf..b67a72e5c6fe85 100644 --- a/arch/ppc/platforms/4xx/ibm440gp.c +++ b/arch/ppc/platforms/4xx/ibm440gp.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm440gp.c - * * PPC440GP I/O descriptions * * Matt Porter <mporter@mvista.com> diff --git a/arch/ppc/platforms/4xx/ibm440gp.h b/arch/ppc/platforms/4xx/ibm440gp.h index ae1efc03b29540..7b2763b6024f76 100644 --- a/arch/ppc/platforms/4xx/ibm440gp.h +++ b/arch/ppc/platforms/4xx/ibm440gp.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm440gp.h - * * PPC440GP definitions * * Roland Dreier <roland@digitalvampire.org> diff --git a/arch/ppc/platforms/4xx/ibm440gx.c b/arch/ppc/platforms/4xx/ibm440gx.c index d24c09ee7b1805..685abffcb6cee1 100644 --- a/arch/ppc/platforms/4xx/ibm440gx.c +++ b/arch/ppc/platforms/4xx/ibm440gx.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm440gx.c - * * PPC440GX I/O descriptions * * Matt Porter <mporter@mvista.com> diff --git a/arch/ppc/platforms/4xx/ibm440gx.h b/arch/ppc/platforms/4xx/ibm440gx.h index 0b59d8dcd03ccb..070a34efe1c7c5 100644 --- a/arch/ppc/platforms/4xx/ibm440gx.h +++ b/arch/ppc/platforms/4xx/ibm440gx.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/ibm440gx.h - * * PPC440GX definitions * * Matt Porter <mporter@mvista.com> diff --git a/arch/ppc/platforms/4xx/ibm440sp.c b/arch/ppc/platforms/4xx/ibm440sp.c index 71a0117d3597e1..de8f7ac5623c1e 100644 --- a/arch/ppc/platforms/4xx/ibm440sp.c +++ b/arch/ppc/platforms/4xx/ibm440sp.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm440sp.c - * * PPC440SP I/O descriptions * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/platforms/4xx/ibm440sp.h b/arch/ppc/platforms/4xx/ibm440sp.h index c71e46a18b9e1a..77e8bb22c527f6 100644 --- a/arch/ppc/platforms/4xx/ibm440sp.h +++ b/arch/ppc/platforms/4xx/ibm440sp.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm440sp.h - * * PPC440SP definitions * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/platforms/4xx/ibmnp405h.c b/arch/ppc/platforms/4xx/ibmnp405h.c index a477a78f490295..f1dcb0ac15b794 100644 --- a/arch/ppc/platforms/4xx/ibmnp405h.c +++ b/arch/ppc/platforms/4xx/ibmnp405h.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibmnp405h.c - * * Author: Armin Kuster <akuster@mvista.com> * * 2000-2002 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/4xx/ibmnp405h.h b/arch/ppc/platforms/4xx/ibmnp405h.h index e2c2b06128c88f..2c683f6aaa6699 100644 --- a/arch/ppc/platforms/4xx/ibmnp405h.h +++ b/arch/ppc/platforms/4xx/ibmnp405h.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibmnp405h.h - * * Author: Armin Kuster <akuster@mvista.com> * * 2002 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/4xx/ibmstb4.c b/arch/ppc/platforms/4xx/ibmstb4.c index 7e33bb635443e8..799a2eccccc391 100644 --- a/arch/ppc/platforms/4xx/ibmstb4.c +++ b/arch/ppc/platforms/4xx/ibmstb4.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibmstb4.c - * * Author: Armin Kuster <akuster@mvista.com> * * 2000-2001 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/4xx/ibmstb4.h b/arch/ppc/platforms/4xx/ibmstb4.h index 9f21d4c88a3d21..9de4265973510a 100644 --- a/arch/ppc/platforms/4xx/ibmstb4.h +++ b/arch/ppc/platforms/4xx/ibmstb4.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibmstb4.h - * * Author: Armin Kuster <akuster@mvista.com> * * 2001 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/4xx/ibmstbx25.c b/arch/ppc/platforms/4xx/ibmstbx25.c index b895b9cca57dd4..090ddcbecc5e7f 100644 --- a/arch/ppc/platforms/4xx/ibmstbx25.c +++ b/arch/ppc/platforms/4xx/ibmstbx25.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibmstbx25.c - * * Author: Armin Kuster <akuster@mvista.com> * * 2000-2002 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/4xx/ibmstbx25.h b/arch/ppc/platforms/4xx/ibmstbx25.h index 9a2efc366e9c61..6884a49d348220 100644 --- a/arch/ppc/platforms/4xx/ibmstbx25.h +++ b/arch/ppc/platforms/4xx/ibmstbx25.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibmstbx25.h - * * Author: Armin Kuster <akuster@mvista.com> * * 2002 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/4xx/luan.c b/arch/ppc/platforms/4xx/luan.c index 21d29132aebd97..5c37de28e13520 100644 --- a/arch/ppc/platforms/4xx/luan.c +++ b/arch/ppc/platforms/4xx/luan.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/luan.c - * * Luan board specific routines * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/platforms/4xx/luan.h b/arch/ppc/platforms/4xx/luan.h index bbe7d0766db8ac..e0db6a810febb4 100644 --- a/arch/ppc/platforms/4xx/luan.h +++ b/arch/ppc/platforms/4xx/luan.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/luan.h - * * Luan board definitions * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/platforms/4xx/ocotea.c b/arch/ppc/platforms/4xx/ocotea.c index 4f355b6acab2b2..f841972f1fa920 100644 --- a/arch/ppc/platforms/4xx/ocotea.c +++ b/arch/ppc/platforms/4xx/ocotea.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ocotea.c - * * Ocotea board specific routines * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/platforms/4xx/ocotea.h b/arch/ppc/platforms/4xx/ocotea.h index 33251153ac5fff..7c799a9ff82b40 100644 --- a/arch/ppc/platforms/4xx/ocotea.h +++ b/arch/ppc/platforms/4xx/ocotea.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/ocotea.h - * * Ocotea board definitions * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/platforms/4xx/ppc440spe.c b/arch/ppc/platforms/4xx/ppc440spe.c index 6139a0b3393e15..1be5d1c8e266db 100644 --- a/arch/ppc/platforms/4xx/ppc440spe.c +++ b/arch/ppc/platforms/4xx/ppc440spe.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ppc440spe.c - * * PPC440SPe I/O descriptions * * Roland Dreier <rolandd@cisco.com> diff --git a/arch/ppc/platforms/4xx/ppc440spe.h b/arch/ppc/platforms/4xx/ppc440spe.h index 2216846973b837..d3a620ddcdee3d 100644 --- a/arch/ppc/platforms/4xx/ppc440spe.h +++ b/arch/ppc/platforms/4xx/ppc440spe.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/ibm440spe.h - * * PPC440SPe definitions * * Roland Dreier <rolandd@cisco.com> diff --git a/arch/ppc/platforms/4xx/redwood5.c b/arch/ppc/platforms/4xx/redwood5.c index 611ac861804d31..53da2b4f7c24ac 100644 --- a/arch/ppc/platforms/4xx/redwood5.c +++ b/arch/ppc/platforms/4xx/redwood5.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/redwood5.c - * * Support for the IBM redwood5 eval board file * * Author: Armin Kuster <akuster@mvista.com> diff --git a/arch/ppc/platforms/4xx/redwood5.h b/arch/ppc/platforms/4xx/redwood5.h index 264e34fb3fbd6f..49edd481897096 100644 --- a/arch/ppc/platforms/4xx/redwood5.h +++ b/arch/ppc/platforms/4xx/redwood5.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/redwood5.h - * * Macros, definitions, and data structures specific to the IBM PowerPC * STB03xxx "Redwood" evaluation board. * diff --git a/arch/ppc/platforms/4xx/redwood6.c b/arch/ppc/platforms/4xx/redwood6.c index b13116691289fa..41b27d106fa3b6 100644 --- a/arch/ppc/platforms/4xx/redwood6.c +++ b/arch/ppc/platforms/4xx/redwood6.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/redwood6.c - * * Author: Armin Kuster <akuster@mvista.com> * * 2002 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/4xx/redwood6.h b/arch/ppc/platforms/4xx/redwood6.h index 1814b9f5fc3a2e..1edcbe5c51c7f2 100644 --- a/arch/ppc/platforms/4xx/redwood6.h +++ b/arch/ppc/platforms/4xx/redwood6.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/redwood6.h - * * Macros, definitions, and data structures specific to the IBM PowerPC * STBx25xx "Redwood6" evaluation board. * diff --git a/arch/ppc/platforms/4xx/sycamore.c b/arch/ppc/platforms/4xx/sycamore.c index 281b4a2ffb968c..bab31eb306874f 100644 --- a/arch/ppc/platforms/4xx/sycamore.c +++ b/arch/ppc/platforms/4xx/sycamore.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/sycamore.c - * * Architecture- / platform-specific boot-time initialization code for * IBM PowerPC 4xx based boards. * diff --git a/arch/ppc/platforms/4xx/sycamore.h b/arch/ppc/platforms/4xx/sycamore.h index 1cd6c824fd62ef..dae01620227ddf 100644 --- a/arch/ppc/platforms/4xx/sycamore.h +++ b/arch/ppc/platforms/4xx/sycamore.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/sycamore.h - * * Sycamore board definitions * * Copyright (c) 2005 DENX Software Engineering diff --git a/arch/ppc/platforms/4xx/virtex-ii_pro.c b/arch/ppc/platforms/4xx/virtex-ii_pro.c deleted file mode 100644 index 097cc9d5aca09c..00000000000000 --- a/arch/ppc/platforms/4xx/virtex-ii_pro.c +++ /dev/null @@ -1,60 +0,0 @@ -/* - * arch/ppc/platforms/4xx/virtex-ii_pro.c - * - * Author: MontaVista Software, Inc. - * source@mvista.com - * - * 2002-2004 (c) MontaVista Software, Inc. This file is licensed under the - * terms of the GNU General Public License version 2. This program is licensed - * "as is" without any warranty of any kind, whether express or implied. - */ - -#include <linux/config.h> -#include <linux/init.h> -#include <asm/ocp.h> -#include "virtex-ii_pro.h" - -/* Have OCP take care of the serial ports. */ -struct ocp_def core_ocp[] = { -#ifdef XPAR_UARTNS550_0_BASEADDR - { .vendor = OCP_VENDOR_XILINX, - .function = OCP_FUNC_16550, - .index = 0, - .paddr = XPAR_UARTNS550_0_BASEADDR, - .irq = XPAR_INTC_0_UARTNS550_0_VEC_ID, - .pm = OCP_CPM_NA - }, -#ifdef XPAR_UARTNS550_1_BASEADDR - { .vendor = OCP_VENDOR_XILINX, - .function = OCP_FUNC_16550, - .index = 1, - .paddr = XPAR_UARTNS550_1_BASEADDR, - .irq = XPAR_INTC_0_UARTNS550_1_VEC_ID, - .pm = OCP_CPM_NA - }, -#ifdef XPAR_UARTNS550_2_BASEADDR - { .vendor = OCP_VENDOR_XILINX, - .function = OCP_FUNC_16550, - .index = 2, - .paddr = XPAR_UARTNS550_2_BASEADDR, - .irq = XPAR_INTC_0_UARTNS550_2_VEC_ID, - .pm = OCP_CPM_NA - }, -#ifdef XPAR_UARTNS550_3_BASEADDR - { .vendor = OCP_VENDOR_XILINX, - .function = OCP_FUNC_16550, - .index = 3, - .paddr = XPAR_UARTNS550_3_BASEADDR, - .irq = XPAR_INTC_0_UARTNS550_3_VEC_ID, - .pm = OCP_CPM_NA - }, -#ifdef XPAR_UARTNS550_4_BASEADDR -#error Edit this file to add more devices. -#endif /* 4 */ -#endif /* 3 */ -#endif /* 2 */ -#endif /* 1 */ -#endif /* 0 */ - { .vendor = OCP_VENDOR_INVALID - } -}; diff --git a/arch/ppc/platforms/4xx/virtex-ii_pro.h b/arch/ppc/platforms/4xx/virtex-ii_pro.h deleted file mode 100644 index 9014c48873397e..00000000000000 --- a/arch/ppc/platforms/4xx/virtex-ii_pro.h +++ /dev/null @@ -1,99 +0,0 @@ -/* - * arch/ppc/platforms/4xx/virtex-ii_pro.h - * - * Include file that defines the Xilinx Virtex-II Pro processor - * - * Author: MontaVista Software, Inc. - * source@mvista.com - * - * 2002-2004 (c) MontaVista Software, Inc. This file is licensed under the - * terms of the GNU General Public License version 2. This program is licensed - * "as is" without any warranty of any kind, whether express or implied. - */ - -#ifdef __KERNEL__ -#ifndef __ASM_VIRTEXIIPRO_H__ -#define __ASM_VIRTEXIIPRO_H__ - -#include <linux/config.h> -#include <asm/xparameters.h> - -/* serial defines */ - -#define RS_TABLE_SIZE 4 /* change this and add more devices below - if you have more then 4 16x50 UARTs */ - -#define BASE_BAUD (XPAR_UARTNS550_0_CLOCK_FREQ_HZ/16) - -/* The serial ports in the Virtex-II Pro have each I/O byte in the - * LSByte of a word. This means that iomem_reg_shift needs to be 2 to - * change the byte offsets into word offsets. In addition the base - * addresses need to have 3 added to them to get to the LSByte. - */ -#define STD_UART_OP(num) \ - { 0, BASE_BAUD, 0, XPAR_INTC_0_UARTNS550_##num##_VEC_ID, \ - ASYNC_BOOT_AUTOCONF, \ - .iomem_base = (u8 *)XPAR_UARTNS550_##num##_BASEADDR + 3, \ - .iomem_reg_shift = 2, \ - .io_type = SERIAL_IO_MEM}, - -#if defined(XPAR_INTC_0_UARTNS550_0_VEC_ID) -#define ML300_UART0 STD_UART_OP(0) -#else -#define ML300_UART0 -#endif - -#if defined(XPAR_INTC_0_UARTNS550_1_VEC_ID) -#define ML300_UART1 STD_UART_OP(1) -#else -#define ML300_UART1 -#endif - -#if defined(XPAR_INTC_0_UARTNS550_2_VEC_ID) -#define ML300_UART2 STD_UART_OP(2) -#else -#define ML300_UART2 -#endif - -#if defined(XPAR_INTC_0_UARTNS550_3_VEC_ID) -#define ML300_UART3 STD_UART_OP(3) -#else -#define ML300_UART3 -#endif - -#if defined(XPAR_INTC_0_UARTNS550_4_VEC_ID) -#error Edit this file to add more devices. -#elif defined(XPAR_INTC_0_UARTNS550_3_VEC_ID) -#define NR_SER_PORTS 4 -#elif defined(XPAR_INTC_0_UARTNS550_2_VEC_ID) -#define NR_SER_PORTS 3 -#elif defined(XPAR_INTC_0_UARTNS550_1_VEC_ID) -#define NR_SER_PORTS 2 -#elif defined(XPAR_INTC_0_UARTNS550_0_VEC_ID) -#define NR_SER_PORTS 1 -#else -#define NR_SER_PORTS 0 -#endif - -#if defined(CONFIG_UART0_TTYS0) -#define SERIAL_PORT_DFNS \ - ML300_UART0 \ - ML300_UART1 \ - ML300_UART2 \ - ML300_UART3 -#endif - -#if defined(CONFIG_UART0_TTYS1) -#define SERIAL_PORT_DFNS \ - ML300_UART1 \ - ML300_UART0 \ - ML300_UART2 \ - ML300_UART3 -#endif - -#define DCRN_CPMFR_BASE 0 - -#include <asm/ibm405.h> - -#endif /* __ASM_VIRTEXIIPRO_H__ */ -#endif /* __KERNEL__ */ diff --git a/arch/ppc/platforms/4xx/virtex.c b/arch/ppc/platforms/4xx/virtex.c new file mode 100644 index 00000000000000..133a83147199f7 --- /dev/null +++ b/arch/ppc/platforms/4xx/virtex.c @@ -0,0 +1,56 @@ +/* + * Virtex-II Pro & Virtex-4 FX common infrastructure + * + * Maintainer: Grant Likely <grant.likely@secretlab.ca> + * + * Copyright 2005 Secret Lab Technologies Ltd. + * Copyright 2005 General Dynamics Canada Ltd. + * Copyright 2005 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/device.h> +#include <linux/serial_8250.h> +#include <asm/ppc_sys.h> +#include <platforms/4xx/virtex.h> +#include <platforms/4xx/xparameters/xparameters.h> + +#define XPAR_UART(num) { \ + .mapbase = XPAR_UARTNS550_##num##_BASEADDR + 3, \ + .irq = XPAR_INTC_0_UARTNS550_##num##_VEC_ID, \ + .iotype = UPIO_MEM, \ + .uartclk = XPAR_UARTNS550_##num##_CLOCK_FREQ_HZ, \ + .flags = UPF_BOOT_AUTOCONF, \ + .regshift = 2, \ + } + +struct plat_serial8250_port serial_platform_data[] = { +#ifdef XPAR_UARTNS550_0_BASEADDR + XPAR_UART(0), +#endif +#ifdef XPAR_UARTNS550_1_BASEADDR + XPAR_UART(1), +#endif +#ifdef XPAR_UARTNS550_2_BASEADDR + XPAR_UART(2), +#endif +#ifdef XPAR_UARTNS550_3_BASEADDR + XPAR_UART(3), +#endif + { }, /* terminated by empty record */ +}; + +struct platform_device ppc_sys_platform_devices[] = { + [VIRTEX_UART] = { + .name = "serial8250", + .id = 0, + .dev.platform_data = serial_platform_data, + }, +}; + diff --git a/arch/ppc/platforms/4xx/virtex.h b/arch/ppc/platforms/4xx/virtex.h new file mode 100644 index 00000000000000..1a01b81cff11b6 --- /dev/null +++ b/arch/ppc/platforms/4xx/virtex.h @@ -0,0 +1,35 @@ +/* + * arch/ppc/platforms/4xx/virtex.h + * + * Include file that defines the Xilinx Virtex-II Pro processor + * + * Author: MontaVista Software, Inc. + * source@mvista.com + * + * 2002-2004 (c) MontaVista Software, Inc. This file is licensed under the + * terms of the GNU General Public License version 2. This program is licensed + * "as is" without any warranty of any kind, whether express or implied. + */ + +#ifdef __KERNEL__ +#ifndef __ASM_VIRTEX_H__ +#define __ASM_VIRTEX_H__ + +/* serial defines */ + +#include <asm/ibm405.h> + +/* Ugly, ugly, ugly! BASE_BAUD defined here to keep 8250.c happy. */ +#if !defined(BASE_BAUD) + #define BASE_BAUD (0) /* dummy value; not used */ +#endif + +/* Device type enumeration for platform bus definitions */ +#ifndef __ASSEMBLY__ +enum ppc_sys_devices { + VIRTEX_UART, +}; +#endif + +#endif /* __ASM_VIRTEX_H__ */ +#endif /* __KERNEL__ */ diff --git a/arch/ppc/platforms/4xx/walnut.c b/arch/ppc/platforms/4xx/walnut.c index 74cb33182d9fac..6bd77902b9a417 100644 --- a/arch/ppc/platforms/4xx/walnut.c +++ b/arch/ppc/platforms/4xx/walnut.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/walnut.c - * * Architecture- / platform-specific boot-time initialization code for * IBM PowerPC 4xx based boards. Adapted from original * code by Gary Thomas, Cort Dougan <cort@fsmlabs.com>, and Dan Malek diff --git a/arch/ppc/platforms/4xx/walnut.h b/arch/ppc/platforms/4xx/walnut.h index dcf2691698c029..f13a577f0a4192 100644 --- a/arch/ppc/platforms/4xx/walnut.h +++ b/arch/ppc/platforms/4xx/walnut.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/walnut.h - * * Walnut board definitions * * Copyright (c) 2005 DENX Software Engineering diff --git a/arch/ppc/platforms/4xx/xilinx_ml300.c b/arch/ppc/platforms/4xx/xilinx_ml300.c index e90d97f64f76c1..d97a7f269f9780 100644 --- a/arch/ppc/platforms/4xx/xilinx_ml300.c +++ b/arch/ppc/platforms/4xx/xilinx_ml300.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/xilinx_ml300.c - * * Xilinx ML300 evaluation board initialization * * Author: MontaVista Software, Inc. @@ -17,12 +15,14 @@ #include <linux/tty.h> #include <linux/serial.h> #include <linux/serial_core.h> +#include <linux/serial_8250.h> #include <linux/serialP.h> #include <asm/io.h> #include <asm/machdep.h> -#include <asm/ocp.h> +#include <asm/ppc_sys.h> -#include <platforms/4xx/virtex-ii_pro.h> /* for NR_SER_PORTS */ +#include <syslib/gen550.h> +#include <platforms/4xx/xparameters/xparameters.h> /* * As an overview of how the following functions (platform_init, @@ -54,6 +54,22 @@ * ppc4xx_pic_init arch/ppc/syslib/xilinx_pic.c */ +/* Board specifications structures */ +struct ppc_sys_spec *cur_ppc_sys_spec; +struct ppc_sys_spec ppc_sys_specs[] = { + { + /* Only one entry, always assume the same design */ + .ppc_sys_name = "Xilinx ML300 Reference Design", + .mask = 0x00000000, + .value = 0x00000000, + .num_devices = 1, + .device_list = (enum ppc_sys_devices[]) + { + VIRTEX_UART, + }, + }, +}; + #if defined(XPAR_POWER_0_POWERDOWN_BASEADDR) static volatile unsigned *powerdown_base = @@ -80,28 +96,39 @@ ml300_map_io(void) #endif } +/* Early serial support functions */ static void __init +ml300_early_serial_init(int num, struct plat_serial8250_port *pdata) +{ +#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB) + struct uart_port serial_req; + + memset(&serial_req, 0, sizeof(serial_req)); + serial_req.mapbase = pdata->mapbase; + serial_req.membase = pdata->membase; + serial_req.irq = pdata->irq; + serial_req.uartclk = pdata->uartclk; + serial_req.regshift = pdata->regshift; + serial_req.iotype = pdata->iotype; + serial_req.flags = pdata->flags; + gen550_init(num, &serial_req); +#endif +} + +void __init ml300_early_serial_map(void) { #ifdef CONFIG_SERIAL_8250 - struct serial_state old_ports[] = { SERIAL_PORT_DFNS }; - struct uart_port port; - int i; - - /* Setup ioremapped serial port access */ - for (i = 0; i < ARRAY_SIZE(old_ports); i++ ) { - memset(&port, 0, sizeof(port)); - port.membase = ioremap((phys_addr_t)(old_ports[i].iomem_base), 16); - port.irq = old_ports[i].irq; - port.uartclk = old_ports[i].baud_base * 16; - port.regshift = old_ports[i].iomem_reg_shift; - port.iotype = UPIO_MEM; - port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; - port.line = i; - - if (early_serial_setup(&port) != 0) { - printk("Early serial init of port %d failed\n", i); - } + struct plat_serial8250_port *pdata; + int i = 0; + + pdata = (struct plat_serial8250_port *) ppc_sys_get_pdata(VIRTEX_UART); + while(pdata && pdata->flags) + { + pdata->membase = ioremap(pdata->mapbase, 0x100); + ml300_early_serial_init(i, pdata); + pdata++; + i++; } #endif /* CONFIG_SERIAL_8250 */ } @@ -109,9 +136,8 @@ ml300_early_serial_map(void) void __init ml300_setup_arch(void) { - ppc4xx_setup_arch(); /* calls ppc4xx_find_bridges() */ - ml300_early_serial_map(); + ppc4xx_setup_arch(); /* calls ppc4xx_find_bridges() */ /* Identify the system */ printk(KERN_INFO "Xilinx Virtex-II Pro port\n"); @@ -131,6 +157,8 @@ platform_init(unsigned long r3, unsigned long r4, unsigned long r5, { ppc4xx_init(r3, r4, r5, r6, r7); + identify_ppc_sys_by_id(mfspr(SPRN_PVR)); + ppc_md.setup_arch = ml300_setup_arch; ppc_md.setup_io_mappings = ml300_map_io; ppc_md.init_IRQ = ml300_init_irq; diff --git a/arch/ppc/platforms/4xx/xilinx_ml300.h b/arch/ppc/platforms/4xx/xilinx_ml300.h index f8c58841233642..3d57332ba820ba 100644 --- a/arch/ppc/platforms/4xx/xilinx_ml300.h +++ b/arch/ppc/platforms/4xx/xilinx_ml300.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/xilinx_ml300.h - * * Include file that defines the Xilinx ML300 evaluation board * * Author: MontaVista Software, Inc. @@ -16,7 +14,7 @@ #define __ASM_XILINX_ML300_H__ /* ML300 has a Xilinx Virtex-II Pro processor */ -#include <platforms/4xx/virtex-ii_pro.h> +#include <platforms/4xx/virtex.h> #ifndef __ASSEMBLY__ @@ -41,7 +39,7 @@ typedef struct board_info { #define PPC4xx_ONB_IO_VADDR 0u #define PPC4xx_ONB_IO_SIZE 0u -#define PPC4xx_MACHINE_NAME "Xilinx ML300" +#define PPC4xx_MACHINE_NAME "Xilinx ML300 Reference System" #endif /* __ASM_XILINX_ML300_H__ */ #endif /* __KERNEL__ */ diff --git a/arch/ppc/platforms/4xx/xilinx_ml403.c b/arch/ppc/platforms/4xx/xilinx_ml403.c new file mode 100644 index 00000000000000..4c0c7e4c11144a --- /dev/null +++ b/arch/ppc/platforms/4xx/xilinx_ml403.c @@ -0,0 +1,177 @@ +/* + * arch/ppc/platforms/4xx/xilinx_ml403.c + * + * Xilinx ML403 evaluation board initialization + * + * Author: Grant Likely <grant.likely@secretlab.ca> + * + * 2005 (c) Secret Lab Technologies Ltd. + * 2002-2004 (c) MontaVista Software, Inc. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include <linux/config.h> +#include <linux/init.h> +#include <linux/irq.h> +#include <linux/tty.h> +#include <linux/serial.h> +#include <linux/serial_core.h> +#include <linux/serial_8250.h> +#include <linux/serialP.h> +#include <asm/io.h> +#include <asm/machdep.h> +#include <asm/ppc_sys.h> + +#include <syslib/gen550.h> +#include <platforms/4xx/xparameters/xparameters.h> + +/* + * As an overview of how the following functions (platform_init, + * ml403_map_io, ml403_setup_arch and ml403_init_IRQ) fit into the + * kernel startup procedure, here's a call tree: + * + * start_here arch/ppc/kernel/head_4xx.S + * early_init arch/ppc/kernel/setup.c + * machine_init arch/ppc/kernel/setup.c + * platform_init this file + * ppc4xx_init arch/ppc/syslib/ppc4xx_setup.c + * parse_bootinfo + * find_bootinfo + * "setup some default ppc_md pointers" + * MMU_init arch/ppc/mm/init.c + * *ppc_md.setup_io_mappings == ml403_map_io this file + * ppc4xx_map_io arch/ppc/syslib/ppc4xx_setup.c + * start_kernel init/main.c + * setup_arch arch/ppc/kernel/setup.c + * #if defined(CONFIG_KGDB) + * *ppc_md.kgdb_map_scc() == gen550_kgdb_map_scc + * #endif + * *ppc_md.setup_arch == ml403_setup_arch this file + * ppc4xx_setup_arch arch/ppc/syslib/ppc4xx_setup.c + * ppc4xx_find_bridges arch/ppc/syslib/ppc405_pci.c + * init_IRQ arch/ppc/kernel/irq.c + * *ppc_md.init_IRQ == ml403_init_IRQ this file + * ppc4xx_init_IRQ arch/ppc/syslib/ppc4xx_setup.c + * ppc4xx_pic_init arch/ppc/syslib/xilinx_pic.c + */ + +/* Board specifications structures */ +struct ppc_sys_spec *cur_ppc_sys_spec; +struct ppc_sys_spec ppc_sys_specs[] = { + { + /* Only one entry, always assume the same design */ + .ppc_sys_name = "Xilinx ML403 Reference Design", + .mask = 0x00000000, + .value = 0x00000000, + .num_devices = 1, + .device_list = (enum ppc_sys_devices[]) + { + VIRTEX_UART, + }, + }, +}; + +#if defined(XPAR_POWER_0_POWERDOWN_BASEADDR) + +static volatile unsigned *powerdown_base = + (volatile unsigned *) XPAR_POWER_0_POWERDOWN_BASEADDR; + +static void +xilinx_power_off(void) +{ + local_irq_disable(); + out_be32(powerdown_base, XPAR_POWER_0_POWERDOWN_VALUE); + while (1) ; +} +#endif + +void __init +ml403_map_io(void) +{ + ppc4xx_map_io(); + +#if defined(XPAR_POWER_0_POWERDOWN_BASEADDR) + powerdown_base = ioremap((unsigned long) powerdown_base, + XPAR_POWER_0_POWERDOWN_HIGHADDR - + XPAR_POWER_0_POWERDOWN_BASEADDR + 1); +#endif +} + +/* Early serial support functions */ +static void __init +ml403_early_serial_init(int num, struct plat_serial8250_port *pdata) +{ +#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB) + struct uart_port serial_req; + + memset(&serial_req, 0, sizeof(serial_req)); + serial_req.mapbase = pdata->mapbase; + serial_req.membase = pdata->membase; + serial_req.irq = pdata->irq; + serial_req.uartclk = pdata->uartclk; + serial_req.regshift = pdata->regshift; + serial_req.iotype = pdata->iotype; + serial_req.flags = pdata->flags; + gen550_init(num, &serial_req); +#endif +} + +void __init +ml403_early_serial_map(void) +{ +#ifdef CONFIG_SERIAL_8250 + struct plat_serial8250_port *pdata; + int i = 0; + + pdata = (struct plat_serial8250_port *) ppc_sys_get_pdata(VIRTEX_UART); + while(pdata && pdata->flags) + { + pdata->membase = ioremap(pdata->mapbase, 0x100); + ml403_early_serial_init(i, pdata); + pdata++; + i++; + } +#endif /* CONFIG_SERIAL_8250 */ +} + +void __init +ml403_setup_arch(void) +{ + ml403_early_serial_map(); + ppc4xx_setup_arch(); /* calls ppc4xx_find_bridges() */ + + /* Identify the system */ + printk(KERN_INFO "Xilinx ML403 Reference System (Virtex-4 FX)\n"); +} + +/* Called after board_setup_irq from ppc4xx_init_IRQ(). */ +void __init +ml403_init_irq(void) +{ + ppc4xx_init_IRQ(); +} + +void __init +platform_init(unsigned long r3, unsigned long r4, unsigned long r5, + unsigned long r6, unsigned long r7) +{ + ppc4xx_init(r3, r4, r5, r6, r7); + + identify_ppc_sys_by_id(mfspr(SPRN_PVR)); + + ppc_md.setup_arch = ml403_setup_arch; + ppc_md.setup_io_mappings = ml403_map_io; + ppc_md.init_IRQ = ml403_init_irq; + +#if defined(XPAR_POWER_0_POWERDOWN_BASEADDR) + ppc_md.power_off = xilinx_power_off; +#endif + +#ifdef CONFIG_KGDB + ppc_md.early_serial_map = ml403_early_serial_map; +#endif +} + diff --git a/arch/ppc/platforms/4xx/xilinx_ml403.h b/arch/ppc/platforms/4xx/xilinx_ml403.h new file mode 100644 index 00000000000000..4735969599024c --- /dev/null +++ b/arch/ppc/platforms/4xx/xilinx_ml403.h @@ -0,0 +1,49 @@ +/* + * arch/ppc/platforms/4xx/xilinx_ml403.h + * + * Include file that defines the Xilinx ML403 reference design + * + * Author: Grant Likely <grant.likely@secretlab.ca> + * + * 2005 (c) Secret Lab Technologies Ltd. + * 2002-2004 (c) MontaVista Software, Inc. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#ifdef __KERNEL__ +#ifndef __ASM_XILINX_ML403_H__ +#define __ASM_XILINX_ML403_H__ + +/* ML403 has a Xilinx Virtex-4 FPGA with a PPC405 hard core */ +#include <platforms/4xx/virtex.h> + +#ifndef __ASSEMBLY__ + +#include <linux/types.h> + +typedef struct board_info { + unsigned int bi_memsize; /* DRAM installed, in bytes */ + unsigned char bi_enetaddr[6]; /* Local Ethernet MAC address */ + unsigned int bi_intfreq; /* Processor speed, in Hz */ + unsigned int bi_busfreq; /* PLB Bus speed, in Hz */ + unsigned int bi_pci_busfreq; /* PCI Bus speed, in Hz */ +} bd_t; + +/* Some 4xx parts use a different timebase frequency from the internal clock. +*/ +#define bi_tbfreq bi_intfreq + +#endif /* !__ASSEMBLY__ */ + +/* We don't need anything mapped. Size of zero will accomplish that. */ +#define PPC4xx_ONB_IO_PADDR 0u +#define PPC4xx_ONB_IO_VADDR 0u +#define PPC4xx_ONB_IO_SIZE 0u + +#define PPC4xx_MACHINE_NAME "Xilinx ML403 Reference Design" + +#endif /* __ASM_XILINX_ML403_H__ */ +#endif /* __KERNEL__ */ diff --git a/arch/ppc/platforms/4xx/xparameters/xparameters.h b/arch/ppc/platforms/4xx/xparameters/xparameters.h new file mode 100644 index 00000000000000..4cf21f25635690 --- /dev/null +++ b/arch/ppc/platforms/4xx/xparameters/xparameters.h @@ -0,0 +1,37 @@ +/* + * include/asm-ppc/xparameters.h + * + * This file includes the correct xparameters.h for the CONFIG'ed board plus + * fixups to translate board specific XPAR values to a common set of names + * + * Author: MontaVista Software, Inc. + * source@mvista.com + * + * 2004 (c) MontaVista Software, Inc. This file is licensed under the terms + * of the GNU General Public License version 2. This program is licensed + * "as is" without any warranty of any kind, whether express or implied. + */ + +#include <linux/config.h> + +#if defined(CONFIG_XILINX_ML300) + #include "xparameters_ml300.h" +#elif defined(CONFIG_XILINX_ML403) + #include "xparameters_ml403.h" +#else + /* Add other board xparameter includes here before the #else */ + #error No xparameters_*.h file included +#endif + +#ifndef SERIAL_PORT_DFNS + /* zImage serial port definitions */ + #define RS_TABLE_SIZE 1 + #define SERIAL_PORT_DFNS { \ + .baud_base = XPAR_UARTNS550_0_CLOCK_FREQ_HZ/16, \ + .irq = XPAR_INTC_0_UARTNS550_0_VEC_ID, \ + .flags = ASYNC_BOOT_AUTOCONF, \ + .iomem_base = (u8 *)XPAR_UARTNS550_0_BASEADDR + 3, \ + .iomem_reg_shift = 2, \ + .io_type = SERIAL_IO_MEM, \ + }, +#endif diff --git a/arch/ppc/platforms/4xx/xparameters/xparameters_ml403.h b/arch/ppc/platforms/4xx/xparameters/xparameters_ml403.h new file mode 100644 index 00000000000000..5cacdcb3964db6 --- /dev/null +++ b/arch/ppc/platforms/4xx/xparameters/xparameters_ml403.h @@ -0,0 +1,243 @@ + +/******************************************************************* +* +* CAUTION: This file is automatically generated by libgen. +* Version: Xilinx EDK 7.1.2 EDK_H.12.5.1 +* DO NOT EDIT. +* +* Copyright (c) 2005 Xilinx, Inc. All rights reserved. +* +* Description: Driver parameters +* +*******************************************************************/ + +#define XPAR_PLB_BRAM_IF_CNTLR_0_BASEADDR 0xFFFF0000 +#define XPAR_PLB_BRAM_IF_CNTLR_0_HIGHADDR 0xFFFFFFFF + +/******************************************************************/ + +#define XPAR_OPB_EMC_0_MEM0_BASEADDR 0x20000000 +#define XPAR_OPB_EMC_0_MEM0_HIGHADDR 0x200FFFFF +#define XPAR_OPB_EMC_0_MEM1_BASEADDR 0x28000000 +#define XPAR_OPB_EMC_0_MEM1_HIGHADDR 0x287FFFFF +#define XPAR_OPB_AC97_CONTROLLER_REF_0_BASEADDR 0xA6000000 +#define XPAR_OPB_AC97_CONTROLLER_REF_0_HIGHADDR 0xA60000FF +#define XPAR_OPB_EMC_USB_0_MEM0_BASEADDR 0xA5000000 +#define XPAR_OPB_EMC_USB_0_MEM0_HIGHADDR 0xA50000FF +#define XPAR_PLB_DDR_0_MEM0_BASEADDR 0x00000000 +#define XPAR_PLB_DDR_0_MEM0_HIGHADDR 0x0FFFFFFF + +/******************************************************************/ + +#define XPAR_XEMAC_NUM_INSTANCES 1 +#define XPAR_OPB_ETHERNET_0_BASEADDR 0x60000000 +#define XPAR_OPB_ETHERNET_0_HIGHADDR 0x60003FFF +#define XPAR_OPB_ETHERNET_0_DEVICE_ID 0 +#define XPAR_OPB_ETHERNET_0_ERR_COUNT_EXIST 1 +#define XPAR_OPB_ETHERNET_0_DMA_PRESENT 1 +#define XPAR_OPB_ETHERNET_0_MII_EXIST 1 + +/******************************************************************/ + +#define XPAR_XUARTNS550_NUM_INSTANCES 1 +#define XPAR_XUARTNS550_CLOCK_HZ 100000000 +#define XPAR_OPB_UART16550_0_BASEADDR 0xA0000000 +#define XPAR_OPB_UART16550_0_HIGHADDR 0xA0001FFF +#define XPAR_OPB_UART16550_0_DEVICE_ID 0 + +/******************************************************************/ + +#define XPAR_XGPIO_NUM_INSTANCES 3 +#define XPAR_OPB_GPIO_0_BASEADDR 0x90000000 +#define XPAR_OPB_GPIO_0_HIGHADDR 0x900001FF +#define XPAR_OPB_GPIO_0_DEVICE_ID 0 +#define XPAR_OPB_GPIO_0_INTERRUPT_PRESENT 0 +#define XPAR_OPB_GPIO_0_IS_DUAL 1 +#define XPAR_OPB_GPIO_EXP_HDR_0_BASEADDR 0x90001000 +#define XPAR_OPB_GPIO_EXP_HDR_0_HIGHADDR 0x900011FF +#define XPAR_OPB_GPIO_EXP_HDR_0_DEVICE_ID 1 +#define XPAR_OPB_GPIO_EXP_HDR_0_INTERRUPT_PRESENT 0 +#define XPAR_OPB_GPIO_EXP_HDR_0_IS_DUAL 1 +#define XPAR_OPB_GPIO_CHAR_LCD_0_BASEADDR 0x90002000 +#define XPAR_OPB_GPIO_CHAR_LCD_0_HIGHADDR 0x900021FF +#define XPAR_OPB_GPIO_CHAR_LCD_0_DEVICE_ID 2 +#define XPAR_OPB_GPIO_CHAR_LCD_0_INTERRUPT_PRESENT 0 +#define XPAR_OPB_GPIO_CHAR_LCD_0_IS_DUAL 0 + +/******************************************************************/ + +#define XPAR_XPS2_NUM_INSTANCES 2 +#define XPAR_OPB_PS2_DUAL_REF_0_DEVICE_ID_0 0 +#define XPAR_OPB_PS2_DUAL_REF_0_BASEADDR_0 0xA9000000 +#define XPAR_OPB_PS2_DUAL_REF_0_HIGHADDR_0 (0xA9000000+0x3F) +#define XPAR_OPB_PS2_DUAL_REF_0_DEVICE_ID_1 1 +#define XPAR_OPB_PS2_DUAL_REF_0_BASEADDR_1 (0xA9000000+0x1000) +#define XPAR_OPB_PS2_DUAL_REF_0_HIGHADDR_1 (0xA9000000+0x103F) + +/******************************************************************/ + +#define XPAR_XIIC_NUM_INSTANCES 1 +#define XPAR_OPB_IIC_0_BASEADDR 0xA8000000 +#define XPAR_OPB_IIC_0_HIGHADDR 0xA80001FF +#define XPAR_OPB_IIC_0_DEVICE_ID 0 +#define XPAR_OPB_IIC_0_TEN_BIT_ADR 0 +#define XPAR_OPB_IIC_0_GPO_WIDTH 1 + +/******************************************************************/ + +#define XPAR_INTC_MAX_NUM_INTR_INPUTS 10 +#define XPAR_XINTC_HAS_IPR 1 +#define XPAR_XINTC_USE_DCR 0 +#define XPAR_XINTC_NUM_INSTANCES 1 +#define XPAR_OPB_INTC_0_BASEADDR 0xD1000FC0 +#define XPAR_OPB_INTC_0_HIGHADDR 0xD1000FDF +#define XPAR_OPB_INTC_0_DEVICE_ID 0 +#define XPAR_OPB_INTC_0_KIND_OF_INTR 0x00000000 + +/******************************************************************/ + +#define XPAR_INTC_SINGLE_BASEADDR 0xD1000FC0 +#define XPAR_INTC_SINGLE_HIGHADDR 0xD1000FDF +#define XPAR_INTC_SINGLE_DEVICE_ID XPAR_OPB_INTC_0_DEVICE_ID +#define XPAR_OPB_ETHERNET_0_IP2INTC_IRPT_MASK 0X000001 +#define XPAR_OPB_INTC_0_OPB_ETHERNET_0_IP2INTC_IRPT_INTR 0 +#define XPAR_SYSTEM_USB_HPI_INT_MASK 0X000002 +#define XPAR_OPB_INTC_0_SYSTEM_USB_HPI_INT_INTR 1 +#define XPAR_MISC_LOGIC_0_PHY_MII_INT_MASK 0X000004 +#define XPAR_OPB_INTC_0_MISC_LOGIC_0_PHY_MII_INT_INTR 2 +#define XPAR_OPB_SYSACE_0_SYSACE_IRQ_MASK 0X000008 +#define XPAR_OPB_INTC_0_OPB_SYSACE_0_SYSACE_IRQ_INTR 3 +#define XPAR_OPB_AC97_CONTROLLER_REF_0_RECORD_INTERRUPT_MASK 0X000010 +#define XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_0_RECORD_INTERRUPT_INTR 4 +#define XPAR_OPB_AC97_CONTROLLER_REF_0_PLAYBACK_INTERRUPT_MASK 0X000020 +#define XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_0_PLAYBACK_INTERRUPT_INTR 5 +#define XPAR_OPB_IIC_0_IP2INTC_IRPT_MASK 0X000040 +#define XPAR_OPB_INTC_0_OPB_IIC_0_IP2INTC_IRPT_INTR 6 +#define XPAR_OPB_PS2_DUAL_REF_0_SYS_INTR2_MASK 0X000080 +#define XPAR_OPB_INTC_0_OPB_PS2_DUAL_REF_0_SYS_INTR2_INTR 7 +#define XPAR_OPB_PS2_DUAL_REF_0_SYS_INTR1_MASK 0X000100 +#define XPAR_OPB_INTC_0_OPB_PS2_DUAL_REF_0_SYS_INTR1_INTR 8 +#define XPAR_OPB_UART16550_0_IP2INTC_IRPT_MASK 0X000200 +#define XPAR_OPB_INTC_0_OPB_UART16550_0_IP2INTC_IRPT_INTR 9 + +/******************************************************************/ + +#define XPAR_XTFT_NUM_INSTANCES 1 +#define XPAR_PLB_TFT_CNTLR_REF_0_DCR_BASEADDR 0xD0000200 +#define XPAR_PLB_TFT_CNTLR_REF_0_DCR_HIGHADDR 0xD0000207 +#define XPAR_PLB_TFT_CNTLR_REF_0_DEVICE_ID 0 + +/******************************************************************/ + +#define XPAR_XSYSACE_MEM_WIDTH 16 +#define XPAR_XSYSACE_NUM_INSTANCES 1 +#define XPAR_OPB_SYSACE_0_BASEADDR 0xCF000000 +#define XPAR_OPB_SYSACE_0_HIGHADDR 0xCF0001FF +#define XPAR_OPB_SYSACE_0_DEVICE_ID 0 +#define XPAR_OPB_SYSACE_0_MEM_WIDTH 16 + +/******************************************************************/ + +#define XPAR_CPU_PPC405_CORE_CLOCK_FREQ_HZ 300000000 + +/******************************************************************/ + + +/******************************************************************/ + +/* Linux Redefines */ + +/******************************************************************/ + +#define XPAR_UARTNS550_0_BASEADDR (XPAR_OPB_UART16550_0_BASEADDR+0x1000) +#define XPAR_UARTNS550_0_HIGHADDR XPAR_OPB_UART16550_0_HIGHADDR +#define XPAR_UARTNS550_0_CLOCK_FREQ_HZ XPAR_XUARTNS550_CLOCK_HZ +#define XPAR_UARTNS550_0_DEVICE_ID XPAR_OPB_UART16550_0_DEVICE_ID + +/******************************************************************/ + +#define XPAR_INTC_0_BASEADDR XPAR_OPB_INTC_0_BASEADDR +#define XPAR_INTC_0_HIGHADDR XPAR_OPB_INTC_0_HIGHADDR +#define XPAR_INTC_0_KIND_OF_INTR XPAR_OPB_INTC_0_KIND_OF_INTR +#define XPAR_INTC_0_DEVICE_ID XPAR_OPB_INTC_0_DEVICE_ID + +/******************************************************************/ + +#define XPAR_INTC_0_EMAC_0_VEC_ID XPAR_OPB_INTC_0_OPB_ETHERNET_0_IP2INTC_IRPT_INTR +#define XPAR_INTC_0_SYSACE_0_VEC_ID XPAR_OPB_INTC_0_OPB_SYSACE_0_SYSACE_IRQ_INTR +#define XPAR_INTC_0_IIC_0_VEC_ID XPAR_OPB_INTC_0_OPB_IIC_0_IP2INTC_IRPT_INTR +#define XPAR_INTC_0_PS2_1_VEC_ID XPAR_OPB_INTC_0_OPB_PS2_DUAL_REF_0_SYS_INTR2_INTR +#define XPAR_INTC_0_PS2_0_VEC_ID XPAR_OPB_INTC_0_OPB_PS2_DUAL_REF_0_SYS_INTR1_INTR +#define XPAR_INTC_0_UARTNS550_0_VEC_ID XPAR_OPB_INTC_0_OPB_UART16550_0_IP2INTC_IRPT_INTR + +/******************************************************************/ + +#define XPAR_TFT_0_BASEADDR XPAR_PLB_TFT_CNTLR_REF_0_DCR_BASEADDR + +/******************************************************************/ + +#define XPAR_EMAC_0_BASEADDR XPAR_OPB_ETHERNET_0_BASEADDR +#define XPAR_EMAC_0_HIGHADDR XPAR_OPB_ETHERNET_0_HIGHADDR +#define XPAR_EMAC_0_DMA_PRESENT XPAR_OPB_ETHERNET_0_DMA_PRESENT +#define XPAR_EMAC_0_MII_EXIST XPAR_OPB_ETHERNET_0_MII_EXIST +#define XPAR_EMAC_0_ERR_COUNT_EXIST XPAR_OPB_ETHERNET_0_ERR_COUNT_EXIST +#define XPAR_EMAC_0_DEVICE_ID XPAR_OPB_ETHERNET_0_DEVICE_ID + +/******************************************************************/ + +#define XPAR_GPIO_0_BASEADDR XPAR_OPB_GPIO_0_BASEADDR_0 +#define XPAR_GPIO_0_HIGHADDR XPAR_OPB_GPIO_0_HIGHADDR_0 +#define XPAR_GPIO_0_DEVICE_ID XPAR_OPB_GPIO_0_DEVICE_ID_0 +#define XPAR_GPIO_1_BASEADDR XPAR_OPB_GPIO_0_BASEADDR_1 +#define XPAR_GPIO_1_HIGHADDR XPAR_OPB_GPIO_0_HIGHADDR_1 +#define XPAR_GPIO_1_DEVICE_ID XPAR_OPB_GPIO_0_DEVICE_ID_1 +#define XPAR_GPIO_2_BASEADDR XPAR_OPB_GPIO_EXP_HDR_0_BASEADDR_0 +#define XPAR_GPIO_2_HIGHADDR XPAR_OPB_GPIO_EXP_HDR_0_HIGHADDR_0 +#define XPAR_GPIO_2_DEVICE_ID XPAR_OPB_GPIO_EXP_HDR_0_DEVICE_ID_0 +#define XPAR_GPIO_3_BASEADDR XPAR_OPB_GPIO_EXP_HDR_0_BASEADDR_1 +#define XPAR_GPIO_3_HIGHADDR XPAR_OPB_GPIO_EXP_HDR_0_HIGHADDR_1 +#define XPAR_GPIO_3_DEVICE_ID XPAR_OPB_GPIO_EXP_HDR_0_DEVICE_ID_1 +#define XPAR_GPIO_4_BASEADDR XPAR_OPB_GPIO_CHAR_LCD_0_BASEADDR +#define XPAR_GPIO_4_HIGHADDR XPAR_OPB_GPIO_CHAR_LCD_0_HIGHADDR +#define XPAR_GPIO_4_DEVICE_ID XPAR_OPB_GPIO_CHAR_LCD_0_DEVICE_ID + +/******************************************************************/ + +#define XPAR_PS2_0_BASEADDR XPAR_OPB_PS2_DUAL_REF_0_BASEADDR_0 +#define XPAR_PS2_0_HIGHADDR XPAR_OPB_PS2_DUAL_REF_0_HIGHADDR_0 +#define XPAR_PS2_0_DEVICE_ID XPAR_OPB_PS2_DUAL_REF_0_DEVICE_ID_0 +#define XPAR_PS2_1_BASEADDR XPAR_OPB_PS2_DUAL_REF_0_BASEADDR_1 +#define XPAR_PS2_1_HIGHADDR XPAR_OPB_PS2_DUAL_REF_0_HIGHADDR_1 +#define XPAR_PS2_1_DEVICE_ID XPAR_OPB_PS2_DUAL_REF_0_DEVICE_ID_1 + +/******************************************************************/ + +#define XPAR_SYSACE_0_BASEADDR XPAR_OPB_SYSACE_0_BASEADDR +#define XPAR_SYSACE_0_HIGHADDR XPAR_OPB_SYSACE_0_HIGHADDR +#define XPAR_SYSACE_0_DEVICE_ID XPAR_OPB_SYSACE_0_DEVICE_ID + +/******************************************************************/ + +#define XPAR_IIC_0_BASEADDR XPAR_OPB_IIC_0_BASEADDR +#define XPAR_IIC_0_HIGHADDR XPAR_OPB_IIC_0_HIGHADDR +#define XPAR_IIC_0_TEN_BIT_ADR XPAR_OPB_IIC_0_TEN_BIT_ADR +#define XPAR_IIC_0_DEVICE_ID XPAR_OPB_IIC_0_DEVICE_ID + +/******************************************************************/ + +#define XPAR_PLB_CLOCK_FREQ_HZ 100000000 +#define XPAR_CORE_CLOCK_FREQ_HZ XPAR_CPU_PPC405_CORE_CLOCK_FREQ_HZ +#define XPAR_DDR_0_SIZE 0x4000000 + +/******************************************************************/ + +#define XPAR_PERSISTENT_0_IIC_0_BASEADDR 0x00000400 +#define XPAR_PERSISTENT_0_IIC_0_HIGHADDR 0x000007FF +#define XPAR_PERSISTENT_0_IIC_0_EEPROMADDR 0xA0 + +/******************************************************************/ + +#define XPAR_PCI_0_CLOCK_FREQ_HZ 0 + +/******************************************************************/ + diff --git a/arch/ppc/platforms/4xx/yucca.c b/arch/ppc/platforms/4xx/yucca.c index b065b8babcd305..f287dcdbffceec 100644 --- a/arch/ppc/platforms/4xx/yucca.c +++ b/arch/ppc/platforms/4xx/yucca.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/yucca.c - * * Yucca board specific routines * * Roland Dreier <rolandd@cisco.com> (based on luan.c by Matt Porter) diff --git a/arch/ppc/platforms/4xx/yucca.h b/arch/ppc/platforms/4xx/yucca.h index 01a4afea151435..7ae23012237af8 100644 --- a/arch/ppc/platforms/4xx/yucca.h +++ b/arch/ppc/platforms/4xx/yucca.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/4xx/yucca.h - * * Yucca board definitions * * Roland Dreier <rolandd@cisco.com> (based on luan.h by Matt Porter) diff --git a/arch/ppc/platforms/83xx/mpc834x_sys.c b/arch/ppc/platforms/83xx/mpc834x_sys.c index 1a659bbc186092..11626dd9090f6a 100644 --- a/arch/ppc/platforms/83xx/mpc834x_sys.c +++ b/arch/ppc/platforms/83xx/mpc834x_sys.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/83xx/mpc834x_sys.c - * * MPC834x SYS board specific routines * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/83xx/mpc834x_sys.h b/arch/ppc/platforms/83xx/mpc834x_sys.h index 2e514d316fb85c..aa86c22cdd2567 100644 --- a/arch/ppc/platforms/83xx/mpc834x_sys.h +++ b/arch/ppc/platforms/83xx/mpc834x_sys.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/83xx/mpc834x_sys.h - * * MPC834X SYS common board definitions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/85xx/mpc8540_ads.c b/arch/ppc/platforms/85xx/mpc8540_ads.c index 408d64f18e1a7e..9b014df516b903 100644 --- a/arch/ppc/platforms/85xx/mpc8540_ads.c +++ b/arch/ppc/platforms/85xx/mpc8540_ads.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/mpc8540_ads.c - * * MPC8540ADS board specific routines * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/85xx/mpc8540_ads.h b/arch/ppc/platforms/85xx/mpc8540_ads.h index e48ca3a97397c3..0b5e7ff856f5e3 100644 --- a/arch/ppc/platforms/85xx/mpc8540_ads.h +++ b/arch/ppc/platforms/85xx/mpc8540_ads.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/mpc8540_ads.h - * * MPC8540ADS board definitions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/85xx/mpc8555_cds.h b/arch/ppc/platforms/85xx/mpc8555_cds.h index 1a8e6c67355d67..9754dbd5d18c72 100644 --- a/arch/ppc/platforms/85xx/mpc8555_cds.h +++ b/arch/ppc/platforms/85xx/mpc8555_cds.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/mpc8555_cds.h - * * MPC8555CDS board definitions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/85xx/mpc8560_ads.c b/arch/ppc/platforms/85xx/mpc8560_ads.c index 442c7ff195d3c1..0cb2e86470e2a3 100644 --- a/arch/ppc/platforms/85xx/mpc8560_ads.c +++ b/arch/ppc/platforms/85xx/mpc8560_ads.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/mpc8560_ads.c - * * MPC8560ADS board specific routines * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/85xx/mpc8560_ads.h b/arch/ppc/platforms/85xx/mpc8560_ads.h index 143ae7eefa7c50..c2247c21fc53aa 100644 --- a/arch/ppc/platforms/85xx/mpc8560_ads.h +++ b/arch/ppc/platforms/85xx/mpc8560_ads.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/mpc8560_ads.h - * * MPC8540ADS board definitions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/85xx/mpc85xx_ads_common.c b/arch/ppc/platforms/85xx/mpc85xx_ads_common.c index 17ce48fe3503e8..8fd9d763f58dc5 100644 --- a/arch/ppc/platforms/85xx/mpc85xx_ads_common.c +++ b/arch/ppc/platforms/85xx/mpc85xx_ads_common.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/mpc85xx_ads_common.c - * * MPC85xx ADS board common routines * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/85xx/mpc85xx_ads_common.h b/arch/ppc/platforms/85xx/mpc85xx_ads_common.h index 198a6a02cde83b..de8d41aafe1160 100644 --- a/arch/ppc/platforms/85xx/mpc85xx_ads_common.h +++ b/arch/ppc/platforms/85xx/mpc85xx_ads_common.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/mpc85xx_ads_common.h - * * MPC85XX ADS common board definitions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/85xx/mpc85xx_cds_common.c b/arch/ppc/platforms/85xx/mpc85xx_cds_common.c index 1801ab392e2223..c9e0aeeca3d87d 100644 --- a/arch/ppc/platforms/85xx/mpc85xx_cds_common.c +++ b/arch/ppc/platforms/85xx/mpc85xx_cds_common.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platform/85xx/mpc85xx_cds_common.c - * * MPC85xx CDS board specific routines * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/85xx/mpc85xx_cds_common.h b/arch/ppc/platforms/85xx/mpc85xx_cds_common.h index 5b588cfd0e41bc..62df54f61ae3aa 100644 --- a/arch/ppc/platforms/85xx/mpc85xx_cds_common.h +++ b/arch/ppc/platforms/85xx/mpc85xx_cds_common.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/mpc85xx_cds_common.h - * * MPC85xx CDS board definitions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/85xx/sbc8560.c b/arch/ppc/platforms/85xx/sbc8560.c index 8a72221f816c87..b73778ecf82787 100644 --- a/arch/ppc/platforms/85xx/sbc8560.c +++ b/arch/ppc/platforms/85xx/sbc8560.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/sbc8560.c - * * Wind River SBC8560 board specific routines * * Maintainer: Kumar Gala diff --git a/arch/ppc/platforms/85xx/sbc8560.h b/arch/ppc/platforms/85xx/sbc8560.h index 5e1b00c77da5e0..44ffaa2d2c87ff 100644 --- a/arch/ppc/platforms/85xx/sbc8560.h +++ b/arch/ppc/platforms/85xx/sbc8560.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/sbc8560.h - * * Wind River SBC8560 board definitions * * Copyright 2003 Motorola Inc. diff --git a/arch/ppc/platforms/85xx/sbc85xx.c b/arch/ppc/platforms/85xx/sbc85xx.c index c02f110219f5e7..d3ff280510ffea 100644 --- a/arch/ppc/platforms/85xx/sbc85xx.c +++ b/arch/ppc/platforms/85xx/sbc85xx.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platform/85xx/sbc85xx.c - * * WindRiver PowerQUICC III SBC85xx board common routines * * Copyright 2002, 2003 Motorola Inc. diff --git a/arch/ppc/platforms/85xx/sbc85xx.h b/arch/ppc/platforms/85xx/sbc85xx.h index 7af93c691a6b4a..5dd8b6a98c9ba5 100644 --- a/arch/ppc/platforms/85xx/sbc85xx.h +++ b/arch/ppc/platforms/85xx/sbc85xx.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/sbc85xx.h - * * WindRiver PowerQUICC III SBC85xx common board definitions * * Copyright 2003 Motorola Inc. diff --git a/arch/ppc/platforms/85xx/stx_gp3.c b/arch/ppc/platforms/85xx/stx_gp3.c index 061bb7cf2d9a18..8d7baa9a397ad1 100644 --- a/arch/ppc/platforms/85xx/stx_gp3.c +++ b/arch/ppc/platforms/85xx/stx_gp3.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/stx_gp3.c - * * STx GP3 board specific routines * * Dan Malek <dan@embeddededge.com> diff --git a/arch/ppc/platforms/85xx/stx_gp3.h b/arch/ppc/platforms/85xx/stx_gp3.h index 2f25b51951520e..3f71f8f5937067 100644 --- a/arch/ppc/platforms/85xx/stx_gp3.h +++ b/arch/ppc/platforms/85xx/stx_gp3.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/stx8560_gp3.h - * * STx GP3 board definitions * * Dan Malek (dan@embeddededge.com) diff --git a/arch/ppc/platforms/85xx/tqm85xx.c b/arch/ppc/platforms/85xx/tqm85xx.c index a5e38ba6273216..00af132262b30b 100644 --- a/arch/ppc/platforms/85xx/tqm85xx.c +++ b/arch/ppc/platforms/85xx/tqm85xx.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/tqm85xx.c - * * TQM85xx (40/41/55/60) board specific routines * * Copyright (c) 2005 DENX Software Engineering diff --git a/arch/ppc/platforms/85xx/tqm85xx.h b/arch/ppc/platforms/85xx/tqm85xx.h index 3775eb363fde58..612d80504f9b5f 100644 --- a/arch/ppc/platforms/85xx/tqm85xx.h +++ b/arch/ppc/platforms/85xx/tqm85xx.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/tqm85xx.h - * * TQM85xx (40/41/55/60) board definitions * * Copyright (c) 2005 DENX Software Engineering diff --git a/arch/ppc/platforms/Makefile b/arch/ppc/platforms/Makefile index 51430e294b322b..e8b91a33ce91f3 100644 --- a/arch/ppc/platforms/Makefile +++ b/arch/ppc/platforms/Makefile @@ -37,6 +37,9 @@ obj-$(CONFIG_SBC82xx) += sbc82xx.o obj-$(CONFIG_SPRUCE) += spruce.o obj-$(CONFIG_LITE5200) += lite5200.o obj-$(CONFIG_EV64360) += ev64360.o +obj-$(CONFIG_MPC86XADS) += mpc866ads_setup.o +obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o +obj-$(CONFIG_ADS8272) += mpc8272ads_setup.o ifeq ($(CONFIG_SMP),y) obj-$(CONFIG_PPC_CHRP) += chrp_smp.o diff --git a/arch/ppc/platforms/apus_setup.c b/arch/ppc/platforms/apus_setup.c index c42c50073da54a..fe0cdc04d4366b 100644 --- a/arch/ppc/platforms/apus_setup.c +++ b/arch/ppc/platforms/apus_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/apus_setup.c - * * Copyright (C) 1998, 1999 Jesper Skov * * Basically what is needed to replace functionality found in diff --git a/arch/ppc/platforms/chestnut.c b/arch/ppc/platforms/chestnut.c index aefcc0e7be5729..f324f757cae16f 100644 --- a/arch/ppc/platforms/chestnut.c +++ b/arch/ppc/platforms/chestnut.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/chestnut.c - * * Board setup routines for IBM Chestnut * * Author: <source@mvista.com> diff --git a/arch/ppc/platforms/chestnut.h b/arch/ppc/platforms/chestnut.h index 0400b2be40ab53..e00fd9f8bbd039 100644 --- a/arch/ppc/platforms/chestnut.h +++ b/arch/ppc/platforms/chestnut.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/chestnut.h - * * Definitions for IBM 750FXGX Eval (Chestnut) * * Author: <source@mvista.com> diff --git a/arch/ppc/platforms/chrp_pegasos_eth.c b/arch/ppc/platforms/chrp_pegasos_eth.c index 108a6e265185b4..9305c8aa137323 100644 --- a/arch/ppc/platforms/chrp_pegasos_eth.c +++ b/arch/ppc/platforms/chrp_pegasos_eth.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/chrp_pegasos_eth.c - * * Copyright (C) 2005 Sven Luther <sl@bplan-gmbh.de> * Thanks to : * Dale Farnsworth <dale@farnsworth.org> diff --git a/arch/ppc/platforms/chrp_setup.c b/arch/ppc/platforms/chrp_setup.c index 48996b787378f6..f9fd3f4f8e2ed4 100644 --- a/arch/ppc/platforms/chrp_setup.c +++ b/arch/ppc/platforms/chrp_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/setup.c - * * Copyright (C) 1995 Linus Torvalds * Adapted from 'alpha' version by Gary Thomas * Modified by Cort Dougan (cort@cs.nmt.edu) diff --git a/arch/ppc/platforms/chrp_time.c b/arch/ppc/platforms/chrp_time.c index 57753a55b5806e..c8627770af139a 100644 --- a/arch/ppc/platforms/chrp_time.c +++ b/arch/ppc/platforms/chrp_time.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/chrp_time.c - * * Copyright (C) 1991, 1992, 1995 Linus Torvalds * * Adapted for PowerPC (PReP) by Gary Thomas diff --git a/arch/ppc/platforms/cpci690.c b/arch/ppc/platforms/cpci690.c index 6ca7bcac947421..55be550a0811e3 100644 --- a/arch/ppc/platforms/cpci690.c +++ b/arch/ppc/platforms/cpci690.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/cpci690.c - * * Board setup routines for the Force CPCI690 board. * * Author: Mark A. Greer <mgreer@mvista.com> diff --git a/arch/ppc/platforms/cpci690.h b/arch/ppc/platforms/cpci690.h index 49584c9cedf38b..0fa5a4c31b6754 100644 --- a/arch/ppc/platforms/cpci690.h +++ b/arch/ppc/platforms/cpci690.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/cpci690.h - * * Definitions for Force CPCI690 * * Author: Mark A. Greer <mgreer@mvista.com> diff --git a/arch/ppc/platforms/ev64260.c b/arch/ppc/platforms/ev64260.c index ffde8f6f6302ff..6444760caa3ac8 100644 --- a/arch/ppc/platforms/ev64260.c +++ b/arch/ppc/platforms/ev64260.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/ev64260.c - * * Board setup routines for the Marvell/Galileo EV-64260-BP Evaluation Board. * * Author: Mark A. Greer <mgreer@mvista.com> diff --git a/arch/ppc/platforms/ev64260.h b/arch/ppc/platforms/ev64260.h index bedffced3a02d6..44d90d56745a53 100644 --- a/arch/ppc/platforms/ev64260.h +++ b/arch/ppc/platforms/ev64260.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/ev64260.h - * * Definitions for Marvell/Galileo EV-64260-BP Evaluation Board. * * Author: Mark A. Greer <mgreer@mvista.com> diff --git a/arch/ppc/platforms/ev64360.c b/arch/ppc/platforms/ev64360.c index b9d844f88c2bc8..b5f52eba4fc168 100644 --- a/arch/ppc/platforms/ev64360.c +++ b/arch/ppc/platforms/ev64360.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/ev64360.c - * * Board setup routines for the Marvell EV-64360-BP Evaluation Board. * * Author: Lee Nicks <allinux@gmail.com> diff --git a/arch/ppc/platforms/ev64360.h b/arch/ppc/platforms/ev64360.h index 68eabe4903977f..b30f4722690a4f 100644 --- a/arch/ppc/platforms/ev64360.h +++ b/arch/ppc/platforms/ev64360.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/ev64360.h - * * Definitions for Marvell EV-64360-BP Evaluation Board. * * Author: Lee Nicks <allinux@gmail.com> diff --git a/arch/ppc/platforms/fads.h b/arch/ppc/platforms/fads.h index a48fb8d723e41a..e1c0b1b6dcb383 100644 --- a/arch/ppc/platforms/fads.h +++ b/arch/ppc/platforms/fads.h @@ -112,7 +112,7 @@ /* CPM Ethernet through SCC1 or SCC2 */ -#ifdef CONFIG_SCC1_ENET /* Probably 860 variant */ +#if defined(CONFIG_SCC1_ENET) || defined(CONFIG_MPC8xx_SECOND_ETH_SCC1) /* Probably 860 variant */ /* Bits in parallel I/O port registers that have to be set/cleared * to configure the pins for SCC1 use. * TCLK - CLK1, RCLK - CLK2. diff --git a/arch/ppc/platforms/gemini.h b/arch/ppc/platforms/gemini.h index 06de5924891863..5528fd0a12168f 100644 --- a/arch/ppc/platforms/gemini.h +++ b/arch/ppc/platforms/gemini.h @@ -1,7 +1,4 @@ /* - * arch/ppc/platforms/gemini.h - * - * * Onboard registers and descriptions for Synergy Microsystems' * "Gemini" boards. * diff --git a/arch/ppc/platforms/gemini_prom.S b/arch/ppc/platforms/gemini_prom.S index 8c5065d565054f..b181f210800121 100644 --- a/arch/ppc/platforms/gemini_prom.S +++ b/arch/ppc/platforms/gemini_prom.S @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/gemini_prom.S - * * Not really prom support code (yet), but sort of anti-prom code. The current * bootloader does a number of things it shouldn't and doesn't do things that it * should. The stuff in here is mainly a hodge-podge collection of setup code diff --git a/arch/ppc/platforms/gemini_setup.c b/arch/ppc/platforms/gemini_setup.c index 729897c59033c4..0090ff154608c3 100644 --- a/arch/ppc/platforms/gemini_setup.c +++ b/arch/ppc/platforms/gemini_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/gemini_setup.c - * * Copyright (C) 1995 Linus Torvalds * Adapted from 'alpha' version by Gary Thomas * Modified by Cort Dougan (cort@cs.nmt.edu) diff --git a/arch/ppc/platforms/hdpu.c b/arch/ppc/platforms/hdpu.c index 50039a204c2495..220674d883df65 100644 --- a/arch/ppc/platforms/hdpu.c +++ b/arch/ppc/platforms/hdpu.c @@ -1,7 +1,4 @@ - /* - * arch/ppc/platforms/hdpu_setup.c - * * Board setup routines for the Sky Computers HDPU Compute Blade. * * Written by Brian Waite <waite@skycomputers.com> diff --git a/arch/ppc/platforms/hdpu.h b/arch/ppc/platforms/hdpu.h index 07c3cffb5c7b77..f9e020b6970ccd 100644 --- a/arch/ppc/platforms/hdpu.h +++ b/arch/ppc/platforms/hdpu.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/hdpu.h - * * Definitions for Sky Computers HDPU board. * * Brian Waite <waite@skycomputers.com> diff --git a/arch/ppc/platforms/katana.c b/arch/ppc/platforms/katana.c index 6e58e30ceed101..d2766617c3cb9e 100644 --- a/arch/ppc/platforms/katana.c +++ b/arch/ppc/platforms/katana.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/katana.c - * * Board setup routines for the Artesyn Katana cPCI boards. * * Author: Tim Montgomery <timm@artesyncp.com> diff --git a/arch/ppc/platforms/katana.h b/arch/ppc/platforms/katana.h index 597257eff2ec5a..0a9b036526b1db 100644 --- a/arch/ppc/platforms/katana.h +++ b/arch/ppc/platforms/katana.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/katana.h - * * Definitions for Artesyn Katana750i/3750 board. * * Author: Tim Montgomery <timm@artesyncp.com> diff --git a/arch/ppc/platforms/lite5200.c b/arch/ppc/platforms/lite5200.c index 7ed52dc340c953..5171b53bccb5e8 100644 --- a/arch/ppc/platforms/lite5200.c +++ b/arch/ppc/platforms/lite5200.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/lite5200.c - * * Platform support file for the Freescale LITE5200 based on MPC52xx. * A maximum of this file should be moved to syslib/mpc52xx_????? * so that new platform based on MPC52xx need a minimal platform file diff --git a/arch/ppc/platforms/lite5200.h b/arch/ppc/platforms/lite5200.h index c1de2aa47175f6..852a18e24d0b3f 100644 --- a/arch/ppc/platforms/lite5200.h +++ b/arch/ppc/platforms/lite5200.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/lite5200.h - * * Definitions for Freescale LITE5200 : MPC52xx Standard Development * Platform board support * diff --git a/arch/ppc/platforms/lopec.c b/arch/ppc/platforms/lopec.c index 06d247c23b8288..c6445a727ca3a8 100644 --- a/arch/ppc/platforms/lopec.c +++ b/arch/ppc/platforms/lopec.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/lopec.c - * * Setup routines for the Motorola LoPEC. * * Author: Dan Cox diff --git a/arch/ppc/platforms/mpc8272ads_setup.c b/arch/ppc/platforms/mpc8272ads_setup.c new file mode 100644 index 00000000000000..bc9b94f77e394f --- /dev/null +++ b/arch/ppc/platforms/mpc8272ads_setup.c @@ -0,0 +1,236 @@ +/* + * arch/ppc/platforms/82xx/pq2ads_pd.c + * + * MPC82xx Board-specific PlatformDevice descriptions + * + * 2005 (c) MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/device.h> +#include <linux/ioport.h> +#include <linux/fs_enet_pd.h> +#include <linux/platform_device.h> + +#include <asm/io.h> +#include <asm/mpc8260.h> +#include <asm/cpm2.h> +#include <asm/immap_cpm2.h> +#include <asm/irq.h> +#include <asm/ppc_sys.h> +#include <asm/ppcboot.h> + +#include "pq2ads_pd.h" + +static void init_fcc1_ioports(void); +static void init_fcc2_ioports(void); + +static struct fs_mii_bus_info mii_bus_info = { + .method = fsmii_bitbang, + .id = 0, + .i.bitbang = { + .mdio_port = fsiop_portc, + .mdio_bit = 18, + .mdc_port = fsiop_portc, + .mdc_bit = 19, + .delay = 1, + }, +}; + +static struct fs_platform_info mpc82xx_fcc1_pdata = { + .fs_no = fsid_fcc1, + .cp_page = CPM_CR_FCC1_PAGE, + .cp_block = CPM_CR_FCC1_SBLOCK, + .clk_trx = (PC_F1RXCLK | PC_F1TXCLK), + .clk_route = CMX1_CLK_ROUTE, + .clk_mask = CMX1_CLK_MASK, + .init_ioports = init_fcc1_ioports, + + .phy_addr = 0, +#ifdef PHY_INTERRUPT + .phy_irq = PHY_INTERRUPT, +#else + .phy_irq = -1; +#endif + .mem_offset = FCC1_MEM_OFFSET, + .bus_info = &mii_bus_info, + .rx_ring = 32, + .tx_ring = 32, + .rx_copybreak = 240, + .use_napi = 0, + .napi_weight = 17, +}; + +static struct fs_platform_info mpc82xx_fcc2_pdata = { + .fs_no = fsid_fcc2, + .cp_page = CPM_CR_FCC2_PAGE, + .cp_block = CPM_CR_FCC2_SBLOCK, + .clk_trx = (PC_F2RXCLK | PC_F2TXCLK), + .clk_route = CMX2_CLK_ROUTE, + .clk_mask = CMX2_CLK_MASK, + .init_ioports = init_fcc2_ioports, + + .phy_addr = 3, +#ifdef PHY_INTERRUPT + .phy_irq = PHY_INTERRUPT, +#else + .phy_irq = -1; +#endif + .mem_offset = FCC2_MEM_OFFSET, + .bus_info = &mii_bus_info, + .rx_ring = 32, + .tx_ring = 32, + .rx_copybreak = 240, + .use_napi = 0, + .napi_weight = 17, +}; + +static void init_fcc1_ioports(void) +{ + struct io_port *io; + u32 tempval; + cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t)); + u32 *bcsr = ioremap(BCSR_ADDR+4, sizeof(u32)); + + io = &immap->im_ioport; + + /* Enable the PHY */ + clrbits32(bcsr, BCSR1_FETHIEN); + setbits32(bcsr, BCSR1_FETH_RST); + + /* FCC1 pins are on port A/C. */ + /* Configure port A and C pins for FCC1 Ethernet. */ + + tempval = in_be32(&io->iop_pdira); + tempval &= ~PA1_DIRA0; + tempval |= PA1_DIRA1; + out_be32(&io->iop_pdira, tempval); + + tempval = in_be32(&io->iop_psora); + tempval &= ~PA1_PSORA0; + tempval |= PA1_PSORA1; + out_be32(&io->iop_psora, tempval); + + setbits32(&io->iop_ppara,PA1_DIRA0 | PA1_DIRA1); + + /* Alter clocks */ + tempval = PC_F1TXCLK|PC_F1RXCLK; + + clrbits32(&io->iop_psorc, tempval); + clrbits32(&io->iop_pdirc, tempval); + setbits32(&io->iop_pparc, tempval); + + clrbits32(&immap->im_cpmux.cmx_fcr, CMX1_CLK_MASK); + setbits32(&immap->im_cpmux.cmx_fcr, CMX1_CLK_ROUTE); + iounmap(bcsr); + iounmap(immap); +} + +static void init_fcc2_ioports(void) +{ + cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t)); + u32 *bcsr = ioremap(BCSR_ADDR+12, sizeof(u32)); + + struct io_port *io; + u32 tempval; + + immap = cpm2_immr; + + io = &immap->im_ioport; + + /* Enable the PHY */ + clrbits32(bcsr, BCSR3_FETHIEN2); + setbits32(bcsr, BCSR3_FETH2_RST); + + /* FCC2 are port B/C. */ + /* Configure port A and C pins for FCC2 Ethernet. */ + + tempval = in_be32(&io->iop_pdirb); + tempval &= ~PB2_DIRB0; + tempval |= PB2_DIRB1; + out_be32(&io->iop_pdirb, tempval); + + tempval = in_be32(&io->iop_psorb); + tempval &= ~PB2_PSORB0; + tempval |= PB2_PSORB1; + out_be32(&io->iop_psorb, tempval); + + setbits32(&io->iop_pparb,PB2_DIRB0 | PB2_DIRB1); + + tempval = PC_F2RXCLK|PC_F2TXCLK; + + /* Alter clocks */ + clrbits32(&io->iop_psorc,tempval); + clrbits32(&io->iop_pdirc,tempval); + setbits32(&io->iop_pparc,tempval); + + clrbits32(&immap->im_cpmux.cmx_fcr, CMX2_CLK_MASK); + setbits32(&immap->im_cpmux.cmx_fcr, CMX2_CLK_ROUTE); + + iounmap(bcsr); + iounmap(immap); +} + + +static void __init mpc8272ads_fixup_enet_pdata(struct platform_device *pdev, + int idx) +{ + bd_t* bi = (void*)__res; + int fs_no = fsid_fcc1+pdev->id-1; + + mpc82xx_fcc1_pdata.dpram_offset = mpc82xx_fcc2_pdata.dpram_offset = (u32)cpm2_immr->im_dprambase; + mpc82xx_fcc1_pdata.fcc_regs_c = mpc82xx_fcc2_pdata.fcc_regs_c = (u32)cpm2_immr->im_fcc_c; + + switch(fs_no) { + case fsid_fcc1: + memcpy(&mpc82xx_fcc1_pdata.macaddr,bi->bi_enetaddr,6); + pdev->dev.platform_data = &mpc82xx_fcc1_pdata; + break; + case fsid_fcc2: + memcpy(&mpc82xx_fcc2_pdata.macaddr,bi->bi_enetaddr,6); + mpc82xx_fcc2_pdata.macaddr[5] ^= 1; + pdev->dev.platform_data = &mpc82xx_fcc2_pdata; + break; + } +} + +static int mpc8272ads_platform_notify(struct device *dev) +{ + static const struct platform_notify_dev_map dev_map[] = { + { + .bus_id = "fsl-cpm-fcc", + .rtn = mpc8272ads_fixup_enet_pdata + }, + { + .bus_id = NULL + } + }; + platform_notify_map(dev_map,dev); + + return 0; + +} + +int __init mpc8272ads_init(void) +{ + printk(KERN_NOTICE "mpc8272ads: Init\n"); + + platform_notify = mpc8272ads_platform_notify; + + ppc_sys_device_initfunc(); + + ppc_sys_device_disable_all(); + ppc_sys_device_enable(MPC82xx_CPM_FCC1); + ppc_sys_device_enable(MPC82xx_CPM_FCC2); + + return 0; +} + +arch_initcall(mpc8272ads_init); diff --git a/arch/ppc/platforms/mpc866ads_setup.c b/arch/ppc/platforms/mpc866ads_setup.c new file mode 100644 index 00000000000000..ac8fcc68afeb30 --- /dev/null +++ b/arch/ppc/platforms/mpc866ads_setup.c @@ -0,0 +1,273 @@ +/*arch/ppc/platforms/mpc885ads-setup.c + * + * Platform setup for the Freescale mpc885ads board + * + * Vitaly Bordug <vbordug@ru.mvista.com> + * + * Copyright 2005 MontaVista Software Inc. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include <linux/config.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/param.h> +#include <linux/string.h> +#include <linux/ioport.h> +#include <linux/device.h> + +#include <linux/fs_enet_pd.h> +#include <linux/mii.h> + +#include <asm/delay.h> +#include <asm/io.h> +#include <asm/machdep.h> +#include <asm/page.h> +#include <asm/processor.h> +#include <asm/system.h> +#include <asm/time.h> +#include <asm/ppcboot.h> +#include <asm/8xx_immap.h> +#include <asm/commproc.h> +#include <asm/ppc_sys.h> +#include <asm/mpc8xx.h> + +extern unsigned char __res[]; + +static struct fs_mii_bus_info fec_mii_bus_info = { + .method = fsmii_fec, + .id = 0, +}; + +static struct fs_mii_bus_info scc_mii_bus_info = { + .method = fsmii_fixed, + .id = 0, + .i.fixed.speed = 10, + .i.fixed.duplex = 0, +}; + +static struct fs_platform_info mpc8xx_fec_pdata[] = { + { + .rx_ring = 128, + .tx_ring = 16, + .rx_copybreak = 240, + + .use_napi = 1, + .napi_weight = 17, + + .phy_addr = 15, + .phy_irq = -1, + + .use_rmii = 0, + + .bus_info = &fec_mii_bus_info, + } +}; + +static struct fs_platform_info mpc8xx_scc_pdata = { + .rx_ring = 64, + .tx_ring = 8, + .rx_copybreak = 240, + + .use_napi = 1, + .napi_weight = 17, + + .phy_addr = -1, + .phy_irq = -1, + + .bus_info = &scc_mii_bus_info, +}; + +void __init board_init(void) +{ + volatile cpm8xx_t *cp = cpmp; + unsigned *bcsr_io; + + bcsr_io = ioremap(BCSR1, sizeof(unsigned long)); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR1\n"); + return; + } +#ifdef CONFIG_SERIAL_CPM_SMC1 + cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */ + clrbits32(bcsr_io,(0x80000000 >> 7)); +#else + setbits32(bcsr_io,(0x80000000 >> 7)); + + cp->cp_pbpar &= ~(0x000000c0); + cp->cp_pbdir |= 0x000000c0; + cp->cp_smc[0].smc_smcmr = 0; + cp->cp_smc[0].smc_smce = 0; +#endif + +#ifdef CONFIG_SERIAL_CPM_SMC2 + cp->cp_simode &= ~(0xe0000000 >> 1); + cp->cp_simode |= (0x20000000 >> 1); /* brg2 */ + clrbits32(bcsr_io,(0x80000000 >> 13)); +#else + clrbits32(bcsr_io,(0x80000000 >> 13)); + cp->cp_pbpar &= ~(0x00000c00); + cp->cp_pbdir |= 0x00000c00; + cp->cp_smc[1].smc_smcmr = 0; + cp->cp_smc[1].smc_smce = 0; +#endif + iounmap(bcsr_io); +} + +static void setup_fec1_ioports(void) +{ + immap_t *immap = (immap_t *) IMAP_ADDR; + + setbits16(&immap->im_ioport.iop_pdpar, 0x1fff); + setbits16(&immap->im_ioport.iop_pddir, 0x1fff); +} + +static void setup_scc1_ioports(void) +{ + immap_t *immap = (immap_t *) IMAP_ADDR; + unsigned *bcsr_io; + + bcsr_io = ioremap(BCSR1, sizeof(unsigned long)); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR1\n"); + return; + } + + /* Enable the PHY. + */ + clrbits32(bcsr_io,BCSR1_ETHEN); + + /* Configure port A pins for Txd and Rxd. + */ + /* Disable receive and transmit in case EPPC-Bug started it. + */ + setbits16(&immap->im_ioport.iop_papar, PA_ENET_RXD | PA_ENET_TXD); + clrbits16(&immap->im_ioport.iop_padir, PA_ENET_RXD | PA_ENET_TXD); + clrbits16(&immap->im_ioport.iop_paodr, PA_ENET_TXD); + + /* Configure port C pins to enable CLSN and RENA. + */ + clrbits16(&immap->im_ioport.iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA); + clrbits16(&immap->im_ioport.iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA); + setbits16(&immap->im_ioport.iop_pcso, PC_ENET_CLSN | PC_ENET_RENA); + /* Configure port A for TCLK and RCLK. + */ + setbits16(&immap->im_ioport.iop_papar, PA_ENET_TCLK | PA_ENET_RCLK); + clrbits16(&immap->im_ioport.iop_padir, PA_ENET_TCLK | PA_ENET_RCLK); + clrbits32(&immap->im_cpm.cp_pbpar, PB_ENET_TENA); + clrbits32(&immap->im_cpm.cp_pbdir, PB_ENET_TENA); + + /* Configure Serial Interface clock routing. + * First, clear all SCC bits to zero, then set the ones we want. + */ + clrbits32(&immap->im_cpm.cp_sicr, SICR_ENET_MASK); + setbits32(&immap->im_cpm.cp_sicr, SICR_ENET_CLKRT); + + /* In the original SCC enet driver the following code is placed at + the end of the initialization */ + setbits32(&immap->im_cpm.cp_pbpar, PB_ENET_TENA); + setbits32(&immap->im_cpm.cp_pbdir, PB_ENET_TENA); + +} + +static void mpc866ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no) +{ + struct fs_platform_info *fpi = pdev->dev.platform_data; + + volatile cpm8xx_t *cp; + bd_t *bd = (bd_t *) __res; + char *e; + int i; + + /* Get pointer to Communication Processor */ + cp = cpmp; + switch (fs_no) { + case fsid_fec1: + fpi = &mpc8xx_fec_pdata[0]; + fpi->init_ioports = &setup_fec1_ioports; + + break; + case fsid_scc1: + fpi = &mpc8xx_scc_pdata; + fpi->init_ioports = &setup_scc1_ioports; + + break; + default: + printk(KERN_WARNING"Device %s is not supported!\n", pdev->name); + return; + } + + pdev->dev.platform_data = fpi; + fpi->fs_no = fs_no; + + e = (unsigned char *)&bd->bi_enetaddr; + for (i = 0; i < 6; i++) + fpi->macaddr[i] = *e++; + + fpi->macaddr[5 - pdev->id]++; + +} + +static void mpc866ads_fixup_fec_enet_pdata(struct platform_device *pdev, + int idx) +{ + /* This is for FEC devices only */ + if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec"))) + return; + mpc866ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1); +} + +static void mpc866ads_fixup_scc_enet_pdata(struct platform_device *pdev, + int idx) +{ + /* This is for SCC devices only */ + if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc"))) + return; + + mpc866ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1); +} + +static int mpc866ads_platform_notify(struct device *dev) +{ + static const struct platform_notify_dev_map dev_map[] = { + { + .bus_id = "fsl-cpm-fec", + .rtn = mpc866ads_fixup_fec_enet_pdata, + }, + { + .bus_id = "fsl-cpm-scc", + .rtn = mpc866ads_fixup_scc_enet_pdata, + }, + { + .bus_id = NULL + } + }; + + platform_notify_map(dev_map,dev); + + return 0; +} + +int __init mpc866ads_init(void) +{ + printk(KERN_NOTICE "mpc866ads: Init\n"); + + platform_notify = mpc866ads_platform_notify; + + ppc_sys_device_initfunc(); + ppc_sys_device_disable_all(); + +#ifdef MPC8xx_SECOND_ETH_SCC1 + ppc_sys_device_enable(MPC8xx_CPM_SCC1); +#endif + ppc_sys_device_enable(MPC8xx_CPM_FEC1); + + return 0; +} + +arch_initcall(mpc866ads_init); diff --git a/arch/ppc/platforms/mpc885ads_setup.c b/arch/ppc/platforms/mpc885ads_setup.c new file mode 100644 index 00000000000000..50a99e5f7c687c --- /dev/null +++ b/arch/ppc/platforms/mpc885ads_setup.c @@ -0,0 +1,389 @@ +/*arch/ppc/platforms/mpc885ads-setup.c + * + * Platform setup for the Freescale mpc885ads board + * + * Vitaly Bordug <vbordug@ru.mvista.com> + * + * Copyright 2005 MontaVista Software Inc. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include <linux/config.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/param.h> +#include <linux/string.h> +#include <linux/ioport.h> +#include <linux/device.h> + +#include <linux/fs_enet_pd.h> +#include <linux/mii.h> + +#include <asm/delay.h> +#include <asm/io.h> +#include <asm/machdep.h> +#include <asm/page.h> +#include <asm/processor.h> +#include <asm/system.h> +#include <asm/time.h> +#include <asm/ppcboot.h> +#include <asm/8xx_immap.h> +#include <asm/commproc.h> +#include <asm/ppc_sys.h> + +extern unsigned char __res[]; + +static void __init mpc885ads_scc_phy_init(char); + +static struct fs_mii_bus_info fec_mii_bus_info = { + .method = fsmii_fec, + .id = 0, +}; + +static struct fs_mii_bus_info scc_mii_bus_info = { +#ifdef CONFIG_SCC_ENET_8xx_FIXED + .method = fsmii_fixed, +#else + .method = fsmii_fec, +#endif + + .id = 0, +}; + +static struct fs_platform_info mpc8xx_fec_pdata[] = { + { + .rx_ring = 128, + .tx_ring = 16, + .rx_copybreak = 240, + + .use_napi = 1, + .napi_weight = 17, + + .phy_addr = 0, + .phy_irq = SIU_IRQ7, + + .bus_info = &fec_mii_bus_info, + }, { + .rx_ring = 128, + .tx_ring = 16, + .rx_copybreak = 240, + + .use_napi = 1, + .napi_weight = 17, + + .phy_addr = 1, + .phy_irq = SIU_IRQ7, + + .bus_info = &fec_mii_bus_info, + } +}; + +static struct fs_platform_info mpc8xx_scc_pdata = { + .rx_ring = 64, + .tx_ring = 8, + .rx_copybreak = 240, + + .use_napi = 1, + .napi_weight = 17, + + .phy_addr = 2, +#ifdef CONFIG_MPC8xx_SCC_ENET_FIXED + .phy_irq = -1, +#else + .phy_irq = SIU_IRQ7, +#endif + + .bus_info = &scc_mii_bus_info, +}; + +void __init board_init(void) +{ + volatile cpm8xx_t *cp = cpmp; + unsigned int *bcsr_io; + +#ifdef CONFIG_FS_ENET + immap_t *immap = (immap_t *) IMAP_ADDR; +#endif + bcsr_io = ioremap(BCSR1, sizeof(unsigned long)); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR\n"); + return; + } +#ifdef CONFIG_SERIAL_CPM_SMC1 + cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */ + clrbits32(bcsr_io, BCSR1_RS232EN_1); +#else + setbits32(bcsr_io,BCSR1_RS232EN_1); + cp->cp_smc[0].smc_smcmr = 0; + cp->cp_smc[0].smc_smce = 0; +#endif + +#ifdef CONFIG_SERIAL_CPM_SMC2 + cp->cp_simode &= ~(0xe0000000 >> 1); + cp->cp_simode |= (0x20000000 >> 1); /* brg2 */ + clrbits32(bcsr_io,BCSR1_RS232EN_2); +#else + setbits32(bcsr_io,BCSR1_RS232EN_2); + cp->cp_smc[1].smc_smcmr = 0; + cp->cp_smc[1].smc_smce = 0; +#endif + iounmap(bcsr_io); + +#ifdef CONFIG_FS_ENET + /* use MDC for MII (common) */ + setbits16(&immap->im_ioport.iop_pdpar, 0x0080); + clrbits16(&immap->im_ioport.iop_pddir, 0x0080); +#endif +} + +static void setup_fec1_ioports(void) +{ + immap_t *immap = (immap_t *) IMAP_ADDR; + + /* configure FEC1 pins */ + setbits16(&immap->im_ioport.iop_papar, 0xf830); + setbits16(&immap->im_ioport.iop_padir, 0x0830); + clrbits16(&immap->im_ioport.iop_padir, 0xf000); + setbits32(&immap->im_cpm.cp_pbpar, 0x00001001); + + clrbits32(&immap->im_cpm.cp_pbdir, 0x00001001); + setbits16(&immap->im_ioport.iop_pcpar, 0x000c); + clrbits16(&immap->im_ioport.iop_pcdir, 0x000c); + setbits32(&immap->im_cpm.cp_pepar, 0x00000003); + + setbits32(&immap->im_cpm.cp_pedir, 0x00000003); + clrbits32(&immap->im_cpm.cp_peso, 0x00000003); + clrbits32(&immap->im_cpm.cp_cptr, 0x00000100); +} + +static void setup_fec2_ioports(void) +{ + immap_t *immap = (immap_t *) IMAP_ADDR; + + /* configure FEC2 pins */ + setbits32(&immap->im_cpm.cp_pepar, 0x0003fffc); + setbits32(&immap->im_cpm.cp_pedir, 0x0003fffc); + setbits32(&immap->im_cpm.cp_peso, 0x00037800); + clrbits32(&immap->im_cpm.cp_peso, 0x000087fc); + clrbits32(&immap->im_cpm.cp_cptr, 0x00000080); +} + +static void setup_scc3_ioports(void) +{ + immap_t *immap = (immap_t *) IMAP_ADDR; + unsigned *bcsr_io; + + bcsr_io = ioremap(BCSR_ADDR, BCSR_SIZE); + + if (bcsr_io == NULL) { + printk(KERN_CRIT "Could not remap BCSR\n"); + return; + } + + /* Enable the PHY. + */ + setbits32(bcsr_io+4, BCSR4_ETH10_RST); + /* Configure port A pins for Txd and Rxd. + */ + setbits16(&immap->im_ioport.iop_papar, PA_ENET_RXD | PA_ENET_TXD); + clrbits16(&immap->im_ioport.iop_padir, PA_ENET_RXD | PA_ENET_TXD); + + /* Configure port C pins to enable CLSN and RENA. + */ + clrbits16(&immap->im_ioport.iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA); + clrbits16(&immap->im_ioport.iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA); + setbits16(&immap->im_ioport.iop_pcso, PC_ENET_CLSN | PC_ENET_RENA); + + /* Configure port E for TCLK and RCLK. + */ + setbits32(&immap->im_cpm.cp_pepar, PE_ENET_TCLK | PE_ENET_RCLK); + clrbits32(&immap->im_cpm.cp_pepar, PE_ENET_TENA); + clrbits32(&immap->im_cpm.cp_pedir, + PE_ENET_TCLK | PE_ENET_RCLK | PE_ENET_TENA); + clrbits32(&immap->im_cpm.cp_peso, PE_ENET_TCLK | PE_ENET_RCLK); + setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA); + + /* Configure Serial Interface clock routing. + * First, clear all SCC bits to zero, then set the ones we want. + */ + clrbits32(&immap->im_cpm.cp_sicr, SICR_ENET_MASK); + setbits32(&immap->im_cpm.cp_sicr, SICR_ENET_CLKRT); + + /* Disable Rx and Tx. SMC1 sshould be stopped if SCC3 eternet are used. + */ + immap->im_cpm.cp_smc[0].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); + /* On the MPC885ADS SCC ethernet PHY is initialized in the full duplex mode + * by H/W setting after reset. SCC ethernet controller support only half duplex. + * This discrepancy of modes causes a lot of carrier lost errors. + */ + + /* In the original SCC enet driver the following code is placed at + the end of the initialization */ + setbits32(&immap->im_cpm.cp_pepar, PE_ENET_TENA); + clrbits32(&immap->im_cpm.cp_pedir, PE_ENET_TENA); + setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA); + + setbits32(bcsr_io+1, BCSR1_ETHEN); + iounmap(bcsr_io); +} + +static void mpc885ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no) +{ + struct fs_platform_info *fpi = pdev->dev.platform_data; + + volatile cpm8xx_t *cp; + bd_t *bd = (bd_t *) __res; + char *e; + int i; + + /* Get pointer to Communication Processor */ + cp = cpmp; + switch (fs_no) { + case fsid_fec1: + fpi = &mpc8xx_fec_pdata[0]; + fpi->init_ioports = &setup_fec1_ioports; + break; + case fsid_fec2: + fpi = &mpc8xx_fec_pdata[1]; + fpi->init_ioports = &setup_fec2_ioports; + break; + case fsid_scc3: + fpi = &mpc8xx_scc_pdata; + fpi->init_ioports = &setup_scc3_ioports; + mpc885ads_scc_phy_init(fpi->phy_addr); + break; + default: + printk(KERN_WARNING"Device %s is not supported!\n", pdev->name); + return; + } + + pdev->dev.platform_data = fpi; + fpi->fs_no = fs_no; + + e = (unsigned char *)&bd->bi_enetaddr; + for (i = 0; i < 6; i++) + fpi->macaddr[i] = *e++; + + fpi->macaddr[5 - pdev->id]++; + +} + +static void mpc885ads_fixup_fec_enet_pdata(struct platform_device *pdev, + int idx) +{ + /* This is for FEC devices only */ + if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec"))) + return; + mpc885ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1); +} + +static void __init mpc885ads_fixup_scc_enet_pdata(struct platform_device *pdev, + int idx) +{ + /* This is for SCC devices only */ + if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc"))) + return; + + mpc885ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1); +} + +/* SCC ethernet controller does not have MII management channel. FEC1 MII + * channel is used to communicate with the 10Mbit PHY. + */ + +#define MII_ECNTRL_PINMUX 0x4 +#define FEC_ECNTRL_PINMUX 0x00000004 +#define FEC_RCNTRL_MII_MODE 0x00000004 + +/* Make MII read/write commands. + */ +#define mk_mii_write(REG, VAL, PHY_ADDR) (0x50020000 | (((REG) & 0x1f) << 18) | \ + ((VAL) & 0xffff) | ((PHY_ADDR) << 23)) + +static void mpc885ads_scc_phy_init(char phy_addr) +{ + volatile immap_t *immap; + volatile fec_t *fecp; + bd_t *bd; + + bd = (bd_t *) __res; + immap = (immap_t *) IMAP_ADDR; /* pointer to internal registers */ + fecp = &(immap->im_cpm.cp_fec); + + /* Enable MII pins of the FEC1 + */ + setbits16(&immap->im_ioport.iop_pdpar, 0x0080); + clrbits16(&immap->im_ioport.iop_pddir, 0x0080); + /* Set MII speed to 2.5 MHz + */ + out_be32(&fecp->fec_mii_speed, + ((((bd->bi_intfreq + 4999999) / 2500000) / 2) & 0x3F) << 1); + + /* Enable FEC pin MUX + */ + setbits32(&fecp->fec_ecntrl, MII_ECNTRL_PINMUX); + setbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE); + + out_be32(&fecp->fec_mii_data, + mk_mii_write(MII_BMCR, BMCR_ISOLATE, phy_addr)); + udelay(100); + out_be32(&fecp->fec_mii_data, + mk_mii_write(MII_ADVERTISE, + ADVERTISE_10HALF | ADVERTISE_CSMA, phy_addr)); + udelay(100); + + /* Disable FEC MII settings + */ + clrbits32(&fecp->fec_ecntrl, MII_ECNTRL_PINMUX); + clrbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE); + out_be32(&fecp->fec_mii_speed, 0); +} + +static int mpc885ads_platform_notify(struct device *dev) +{ + + static const struct platform_notify_dev_map dev_map[] = { + { + .bus_id = "fsl-cpm-fec", + .rtn = mpc885ads_fixup_fec_enet_pdata, + }, + { + .bus_id = "fsl-cpm-scc", + .rtn = mpc885ads_fixup_scc_enet_pdata, + }, + { + .bus_id = NULL + } + }; + + platform_notify_map(dev_map,dev); + +} + +int __init mpc885ads_init(void) +{ + printk(KERN_NOTICE "mpc885ads: Init\n"); + + platform_notify = mpc885ads_platform_notify; + + ppc_sys_device_initfunc(); + ppc_sys_device_disable_all(); + + ppc_sys_device_enable(MPC8xx_CPM_FEC1); + +#ifdef CONFIG_MPC8xx_SECOND_ETH_SCC3 + ppc_sys_device_enable(MPC8xx_CPM_SCC1); + +#endif +#ifdef CONFIG_MPC8xx_SECOND_ETH_FEC2 + ppc_sys_device_enable(MPC8xx_CPM_FEC2); +#endif + + return 0; +} + +arch_initcall(mpc885ads_init); diff --git a/arch/ppc/platforms/mvme5100.c b/arch/ppc/platforms/mvme5100.c index 108eb182dddcc0..c717cd92c028e5 100644 --- a/arch/ppc/platforms/mvme5100.c +++ b/arch/ppc/platforms/mvme5100.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/mvme5100.c - * * Board setup routines for the Motorola MVME5100. * * Author: Matt Porter <mporter@mvista.com> diff --git a/arch/ppc/platforms/pal4.h b/arch/ppc/platforms/pal4.h index 641a11a3165701..8569c423d88775 100644 --- a/arch/ppc/platforms/pal4.h +++ b/arch/ppc/platforms/pal4.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/pal4.h - * * Definitions for SBS Palomar IV board * * Author: Dan Cox diff --git a/arch/ppc/platforms/pal4_pci.c b/arch/ppc/platforms/pal4_pci.c index c3b1b757a48b7b..d81ae1c7e1cff1 100644 --- a/arch/ppc/platforms/pal4_pci.c +++ b/arch/ppc/platforms/pal4_pci.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/pal4_pci.c - * * PCI support for SBS Palomar IV * * Author: Dan Cox diff --git a/arch/ppc/platforms/pal4_serial.h b/arch/ppc/platforms/pal4_serial.h index a715c66e1adf17..a75343224cfd98 100644 --- a/arch/ppc/platforms/pal4_serial.h +++ b/arch/ppc/platforms/pal4_serial.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/pal4_serial.h - * * Definitions for SBS PalomarIV serial support * * Author: Dan Cox diff --git a/arch/ppc/platforms/pal4_setup.c b/arch/ppc/platforms/pal4_setup.c index f93a3f87193288..3c3d881df00d52 100644 --- a/arch/ppc/platforms/pal4_setup.c +++ b/arch/ppc/platforms/pal4_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/pal4_setup.c - * * Board setup routines for the SBS PalomarIV. * * Author: Dan Cox diff --git a/arch/ppc/platforms/powerpmc250.c b/arch/ppc/platforms/powerpmc250.c index e6b520e6e13fea..c3a86be11fb799 100644 --- a/arch/ppc/platforms/powerpmc250.c +++ b/arch/ppc/platforms/powerpmc250.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/powerpmc250.c - * * Board setup routines for Force PowerPMC-250 Processor PMC * * Author: Troy Benjegerdes <tbenjegerdes@mvista.com> diff --git a/arch/ppc/platforms/pplus.c b/arch/ppc/platforms/pplus.c index 22bd40cfb0928f..de2761ebe0d927 100644 --- a/arch/ppc/platforms/pplus.c +++ b/arch/ppc/platforms/pplus.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/pplus.c - * * Board and PCI setup routines for MCG PowerPlus * * Author: Randy Vinson <rvinson@mvista.com> diff --git a/arch/ppc/platforms/pplus.h b/arch/ppc/platforms/pplus.h index 90f0cb2d409f0c..a07cbbdd72c68d 100644 --- a/arch/ppc/platforms/pplus.h +++ b/arch/ppc/platforms/pplus.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/pplus.h - * * Definitions for Motorola MCG Falcon/Raven & HAWK North Bridge & Memory ctlr. * * Author: Mark A. Greerinclude/asm-ppc/hawk.h diff --git a/arch/ppc/platforms/pq2ads.c b/arch/ppc/platforms/pq2ads.c index 71c9fca1fe9b9d..3365fd788a7af4 100644 --- a/arch/ppc/platforms/pq2ads.c +++ b/arch/ppc/platforms/pq2ads.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/pq2ads.c - * * PQ2ADS platform support * * Author: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/platforms/pq2ads.h b/arch/ppc/platforms/pq2ads.h index 067d9a5aebc108..6b26dd36c64071 100644 --- a/arch/ppc/platforms/pq2ads.h +++ b/arch/ppc/platforms/pq2ads.h @@ -13,6 +13,10 @@ #include <asm/ppcboot.h> +#if defined(CONFIG_ADS8272) +#define BOARD_CHIP_NAME "8272" +#endif + /* Memory map is configured by the PROM startup. * We just map a few things we need. The CSR is actually 4 byte-wide * registers that can be accessed as 8-, 16-, or 32-bit values. diff --git a/arch/ppc/platforms/pq2ads_pd.h b/arch/ppc/platforms/pq2ads_pd.h new file mode 100644 index 00000000000000..8f14a43eafec02 --- /dev/null +++ b/arch/ppc/platforms/pq2ads_pd.h @@ -0,0 +1,114 @@ +#ifndef __PQ2ADS_PD_H +#define __PQ2ADS_PD_H +/* + * arch/ppc/platforms/82xx/pq2ads_pd.h + * + * Some defines for MPC82xx board-specific PlatformDevice descriptions + * + * 2005 (c) MontaVista Software, Inc. + * Vitaly Bordug <vbordug@ru.mvista.com> + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/* FCC1 Clock Source Configuration. These can be redefined in the board specific file. + Can only choose from CLK9-12 */ + +#define F1_RXCLK 11 +#define F1_TXCLK 10 + +/* FCC2 Clock Source Configuration. These can be redefined in the board specific file. + Can only choose from CLK13-16 */ +#define F2_RXCLK 15 +#define F2_TXCLK 16 + +/* FCC3 Clock Source Configuration. These can be redefined in the board specific file. + Can only choose from CLK13-16 */ +#define F3_RXCLK 13 +#define F3_TXCLK 14 + +/* Automatically generates register configurations */ +#define PC_CLK(x) ((uint)(1<<(x-1))) /* FCC CLK I/O ports */ + +#define CMXFCR_RF1CS(x) ((uint)((x-5)<<27)) /* FCC1 Receive Clock Source */ +#define CMXFCR_TF1CS(x) ((uint)((x-5)<<24)) /* FCC1 Transmit Clock Source */ +#define CMXFCR_RF2CS(x) ((uint)((x-9)<<19)) /* FCC2 Receive Clock Source */ +#define CMXFCR_TF2CS(x) ((uint)((x-9)<<16)) /* FCC2 Transmit Clock Source */ +#define CMXFCR_RF3CS(x) ((uint)((x-9)<<11)) /* FCC3 Receive Clock Source */ +#define CMXFCR_TF3CS(x) ((uint)((x-9)<<8)) /* FCC3 Transmit Clock Source */ + +#define PC_F1RXCLK PC_CLK(F1_RXCLK) +#define PC_F1TXCLK PC_CLK(F1_TXCLK) +#define CMX1_CLK_ROUTE (CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK)) +#define CMX1_CLK_MASK ((uint)0xff000000) + +#define PC_F2RXCLK PC_CLK(F2_RXCLK) +#define PC_F2TXCLK PC_CLK(F2_TXCLK) +#define CMX2_CLK_ROUTE (CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK)) +#define CMX2_CLK_MASK ((uint)0x00ff0000) + +#define PC_F3RXCLK PC_CLK(F3_RXCLK) +#define PC_F3TXCLK PC_CLK(F3_TXCLK) +#define CMX3_CLK_ROUTE (CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK)) +#define CMX3_CLK_MASK ((uint)0x0000ff00) + +/* I/O Pin assignment for FCC1. I don't yet know the best way to do this, + * but there is little variation among the choices. + */ +#define PA1_COL 0x00000001U +#define PA1_CRS 0x00000002U +#define PA1_TXER 0x00000004U +#define PA1_TXEN 0x00000008U +#define PA1_RXDV 0x00000010U +#define PA1_RXER 0x00000020U +#define PA1_TXDAT 0x00003c00U +#define PA1_RXDAT 0x0003c000U +#define PA1_PSORA0 (PA1_RXDAT | PA1_TXDAT) +#define PA1_PSORA1 (PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \ + PA1_RXDV | PA1_RXER) +#define PA1_DIRA0 (PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV) +#define PA1_DIRA1 (PA1_TXDAT | PA1_TXEN | PA1_TXER) + + +/* I/O Pin assignment for FCC2. I don't yet know the best way to do this, + * but there is little variation among the choices. + */ +#define PB2_TXER 0x00000001U +#define PB2_RXDV 0x00000002U +#define PB2_TXEN 0x00000004U +#define PB2_RXER 0x00000008U +#define PB2_COL 0x00000010U +#define PB2_CRS 0x00000020U +#define PB2_TXDAT 0x000003c0U +#define PB2_RXDAT 0x00003c00U +#define PB2_PSORB0 (PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \ + PB2_RXER | PB2_RXDV | PB2_TXER) +#define PB2_PSORB1 (PB2_TXEN) +#define PB2_DIRB0 (PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV) +#define PB2_DIRB1 (PB2_TXDAT | PB2_TXEN | PB2_TXER) + + +/* I/O Pin assignment for FCC3. I don't yet know the best way to do this, + * but there is little variation among the choices. + */ +#define PB3_RXDV 0x00004000U +#define PB3_RXER 0x00008000U +#define PB3_TXER 0x00010000U +#define PB3_TXEN 0x00020000U +#define PB3_COL 0x00040000U +#define PB3_CRS 0x00080000U +#define PB3_TXDAT 0x0f000000U +#define PB3_RXDAT 0x00f00000U +#define PB3_PSORB0 (PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \ + PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN) +#define PB3_PSORB1 0 +#define PB3_DIRB0 (PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV) +#define PB3_DIRB1 (PB3_TXDAT | PB3_TXEN | PB3_TXER) + +#define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128)) +#define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0) +#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1) + +#endif diff --git a/arch/ppc/platforms/prep_setup.c b/arch/ppc/platforms/prep_setup.c index d065358020030a..a0fc628ffb1e51 100644 --- a/arch/ppc/platforms/prep_setup.c +++ b/arch/ppc/platforms/prep_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/setup.c - * * Copyright (C) 1995 Linus Torvalds * Adapted from 'alpha' version by Gary Thomas * Modified by Cort Dougan (cort@cs.nmt.edu) diff --git a/arch/ppc/platforms/prpmc750.c b/arch/ppc/platforms/prpmc750.c index 0bb14a5e824cab..cdd9cfb13ee991 100644 --- a/arch/ppc/platforms/prpmc750.c +++ b/arch/ppc/platforms/prpmc750.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/prpmc750_setup.c - * * Board setup routines for Motorola PrPMC750 * * Author: Matt Porter <mporter@mvista.com> diff --git a/arch/ppc/platforms/prpmc800.c b/arch/ppc/platforms/prpmc800.c index de7baefacd3aa4..e459a199fb1d55 100644 --- a/arch/ppc/platforms/prpmc800.c +++ b/arch/ppc/platforms/prpmc800.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/prpmc800.c - * * Author: Dale Farnsworth <dale.farnsworth@mvista.com> * * 2001-2004 (c) MontaVista, Software, Inc. This file is licensed under diff --git a/arch/ppc/platforms/radstone_ppc7d.c b/arch/ppc/platforms/radstone_ppc7d.c index 872c0a3ba3c798..1b1e7c5ef1525d 100644 --- a/arch/ppc/platforms/radstone_ppc7d.c +++ b/arch/ppc/platforms/radstone_ppc7d.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/radstone_ppc7d.c - * * Board setup routines for the Radstone PPC7D boards. * * Author: James Chapman <jchapman@katalix.com> diff --git a/arch/ppc/platforms/radstone_ppc7d.h b/arch/ppc/platforms/radstone_ppc7d.h index 938375510be48b..2bb093a0c03e98 100644 --- a/arch/ppc/platforms/radstone_ppc7d.h +++ b/arch/ppc/platforms/radstone_ppc7d.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/radstone_ppc7d.h - * * Board definitions for the Radstone PPC7D boards. * * Author: James Chapman <jchapman@katalix.com> diff --git a/arch/ppc/platforms/sandpoint.c b/arch/ppc/platforms/sandpoint.c index 9eeed35723098d..6dc459decb2d10 100644 --- a/arch/ppc/platforms/sandpoint.c +++ b/arch/ppc/platforms/sandpoint.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/sandpoint_setup.c - * * Board setup routines for the Motorola SPS Sandpoint Test Platform. * * Author: Mark A. Greer diff --git a/arch/ppc/platforms/sandpoint.h b/arch/ppc/platforms/sandpoint.h index f4e982cb69df8f..3b64e64184898b 100644 --- a/arch/ppc/platforms/sandpoint.h +++ b/arch/ppc/platforms/sandpoint.h @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/sandpoint.h - * * Definitions for Motorola SPS Sandpoint Test Platform * * Author: Mark A. Greer diff --git a/arch/ppc/platforms/sbc82xx.c b/arch/ppc/platforms/sbc82xx.c index 74c9ff72c3ddcc..866807b4ad0b32 100644 --- a/arch/ppc/platforms/sbc82xx.c +++ b/arch/ppc/platforms/sbc82xx.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/sbc82xx.c - * * SBC82XX platform support * * Author: Guy Streeter <streeter@redhat.com> diff --git a/arch/ppc/platforms/spruce.c b/arch/ppc/platforms/spruce.c index 69e1de7971f2d4..3783deccd9b28d 100644 --- a/arch/ppc/platforms/spruce.c +++ b/arch/ppc/platforms/spruce.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/spruce.c - * * Board and PCI setup routines for IBM Spruce * * Author: MontaVista Software <source@mvista.com> diff --git a/arch/ppc/platforms/tqm8260_setup.c b/arch/ppc/platforms/tqm8260_setup.c index 3409139330b1d9..b766339f44ac51 100644 --- a/arch/ppc/platforms/tqm8260_setup.c +++ b/arch/ppc/platforms/tqm8260_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/tqm8260_setup.c - * * TQM8260 platform support * * Author: Allen Curtis <acurtis@onz.com> diff --git a/arch/ppc/syslib/Makefile b/arch/ppc/syslib/Makefile index 159dcd92a6d129..5cb62c6a51c84c 100644 --- a/arch/ppc/syslib/Makefile +++ b/arch/ppc/syslib/Makefile @@ -17,8 +17,8 @@ obj-$(CONFIG_440GX) += ibm440gx_common.o obj-$(CONFIG_440SP) += ibm440gx_common.o ibm440sp_common.o obj-$(CONFIG_440SPE) += ibm440gx_common.o ibm440sp_common.o ppc440spe_pcie.o ifeq ($(CONFIG_4xx),y) -ifeq ($(CONFIG_VIRTEX_II_PRO),y) -obj-$(CONFIG_40x) += xilinx_pic.o +ifeq ($(CONFIG_XILINX_VIRTEX),y) +obj-$(CONFIG_40x) += xilinx_pic.o ppc_sys.o else ifeq ($(CONFIG_403),y) obj-$(CONFIG_40x) += ppc403_pic.o diff --git a/arch/ppc/syslib/cpc700.h b/arch/ppc/syslib/cpc700.h index f2c002531019e5..0a8a5d84390fc9 100644 --- a/arch/ppc/syslib/cpc700.h +++ b/arch/ppc/syslib/cpc700.h @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/cpc700.h - * * Header file for IBM CPC700 Host Bridge, et. al. * * Author: Mark A. Greer diff --git a/arch/ppc/syslib/cpc700_pic.c b/arch/ppc/syslib/cpc700_pic.c index 75fe8eb1069359..5add0a919ef618 100644 --- a/arch/ppc/syslib/cpc700_pic.c +++ b/arch/ppc/syslib/cpc700_pic.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/cpc700_pic.c - * * Interrupt controller support for IBM Spruce * * Authors: Mark Greer, Matt Porter, and Johnnie Peters diff --git a/arch/ppc/syslib/cpc710.h b/arch/ppc/syslib/cpc710.h index cc0afd80402974..5299bf8b5d0109 100644 --- a/arch/ppc/syslib/cpc710.h +++ b/arch/ppc/syslib/cpc710.h @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/cpc710.h - * * Definitions for the IBM CPC710 PCI Host Bridge * * Author: Matt Porter <mporter@mvista.com> diff --git a/arch/ppc/syslib/gen550.h b/arch/ppc/syslib/gen550.h index 039d249e19a890..5254d3cdbca6c9 100644 --- a/arch/ppc/syslib/gen550.h +++ b/arch/ppc/syslib/gen550.h @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/gen550.h - * * gen550 prototypes * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/syslib/gen550_dbg.c b/arch/ppc/syslib/gen550_dbg.c index 9ef0113c83d1e3..9fcff74bfdd089 100644 --- a/arch/ppc/syslib/gen550_dbg.c +++ b/arch/ppc/syslib/gen550_dbg.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/gen550_dbg.c - * * A library of polled 16550 serial routines. These are intended to * be used to support progress messages, xmon, kgdb, etc. on a * variety of platforms. diff --git a/arch/ppc/syslib/gen550_kgdb.c b/arch/ppc/syslib/gen550_kgdb.c index 7239d5d7ddcdca..874078a7664dc6 100644 --- a/arch/ppc/syslib/gen550_kgdb.c +++ b/arch/ppc/syslib/gen550_kgdb.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/gen550_kgdb.c - * * Generic 16550 kgdb support intended to be useful on a variety * of platforms. To enable this support, it is necessary to set * the CONFIG_GEN550 option. Any virtual mapping of the serial diff --git a/arch/ppc/syslib/gt64260_pic.c b/arch/ppc/syslib/gt64260_pic.c index f97b3a9abd1e48..dc3bd9ecbbf695 100644 --- a/arch/ppc/syslib/gt64260_pic.c +++ b/arch/ppc/syslib/gt64260_pic.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/gt64260_pic.c - * * Interrupt controller support for Galileo's GT64260. * * Author: Chris Zankel <source@mvista.com> diff --git a/arch/ppc/syslib/harrier.c b/arch/ppc/syslib/harrier.c index a6b3f864579321..c1583f4883254b 100644 --- a/arch/ppc/syslib/harrier.c +++ b/arch/ppc/syslib/harrier.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/harrier.c - * * Motorola MCG Harrier northbridge/memory controller support * * Author: Dale Farnsworth diff --git a/arch/ppc/syslib/hawk_common.c b/arch/ppc/syslib/hawk_common.c index a9911dc3a82f9a..c5bf16b0d6a182 100644 --- a/arch/ppc/syslib/hawk_common.c +++ b/arch/ppc/syslib/hawk_common.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/hawk_common.c - * * Common Motorola PowerPlus Platform--really Falcon/Raven or HAWK. * * Author: Mark A. Greer diff --git a/arch/ppc/syslib/ibm440gp_common.c b/arch/ppc/syslib/ibm440gp_common.c index 0d6be2d6dd6794..fbaae5f6d8344e 100644 --- a/arch/ppc/syslib/ibm440gp_common.c +++ b/arch/ppc/syslib/ibm440gp_common.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ibm440gp_common.c - * * PPC440GP system library * * Matt Porter <mporter@mvista.com> diff --git a/arch/ppc/syslib/ibm440gp_common.h b/arch/ppc/syslib/ibm440gp_common.h index a054d83cb1ac50..f48529f3c23d72 100644 --- a/arch/ppc/syslib/ibm440gp_common.h +++ b/arch/ppc/syslib/ibm440gp_common.h @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/ibm440gp_common.h - * * PPC440GP system library * * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> diff --git a/arch/ppc/syslib/ibm440gx_common.c b/arch/ppc/syslib/ibm440gx_common.c index c36db279b43daa..a7dd55f1c63e12 100644 --- a/arch/ppc/syslib/ibm440gx_common.c +++ b/arch/ppc/syslib/ibm440gx_common.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/ibm440gx_common.c - * * PPC440GX system library * * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> diff --git a/arch/ppc/syslib/ibm440gx_common.h b/arch/ppc/syslib/ibm440gx_common.h index e73aa0411d3587..a2ab9fab8e34a5 100644 --- a/arch/ppc/syslib/ibm440gx_common.h +++ b/arch/ppc/syslib/ibm440gx_common.h @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/ibm440gx_common.h - * * PPC440GX system library * * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> diff --git a/arch/ppc/syslib/ibm440sp_common.c b/arch/ppc/syslib/ibm440sp_common.c index cdafda127d81f1..293e4138d172e1 100644 --- a/arch/ppc/syslib/ibm440sp_common.c +++ b/arch/ppc/syslib/ibm440sp_common.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ibm440sp_common.c - * * PPC440SP/PPC440SPe system library * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/syslib/ibm440sp_common.h b/arch/ppc/syslib/ibm440sp_common.h index a21a9906dcc9ed..8077bf8ed118a5 100644 --- a/arch/ppc/syslib/ibm440sp_common.h +++ b/arch/ppc/syslib/ibm440sp_common.h @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ibm440sp_common.h - * * PPC440SP system library * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/syslib/ibm44x_common.c b/arch/ppc/syslib/ibm44x_common.c index 71db11d2215840..14a981a5cea724 100644 --- a/arch/ppc/syslib/ibm44x_common.c +++ b/arch/ppc/syslib/ibm44x_common.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ibm44x_common.c - * * PPC44x system library * * Matt Porter <mporter@kernel.crashing.org> diff --git a/arch/ppc/syslib/ibm44x_common.h b/arch/ppc/syslib/ibm44x_common.h index b25a8995e4e9c9..f179db8634e088 100644 --- a/arch/ppc/syslib/ibm44x_common.h +++ b/arch/ppc/syslib/ibm44x_common.h @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/ibm44x_common.h - * * PPC44x system library * * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> diff --git a/arch/ppc/syslib/m8260_pci_erratum9.c b/arch/ppc/syslib/m8260_pci_erratum9.c index 1dc7e4e1d4914e..99e4bc0e42af00 100644 --- a/arch/ppc/syslib/m8260_pci_erratum9.c +++ b/arch/ppc/syslib/m8260_pci_erratum9.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/mpc8260_pci9.c - * * Workaround for device erratum PCI 9. * See Motorola's "XPC826xA Family Device Errata Reference." * The erratum applies to all 8260 family Hip4 processors. It is scheduled diff --git a/arch/ppc/syslib/m8260_setup.c b/arch/ppc/syslib/m8260_setup.c index 76a2aa4ce65e17..b7a6cb2d8d526b 100644 --- a/arch/ppc/syslib/m8260_setup.c +++ b/arch/ppc/syslib/m8260_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/m8260_setup.c - * * Copyright (C) 1995 Linus Torvalds * Adapted from 'alpha' version by Gary Thomas * Modified by Cort Dougan (cort@cs.nmt.edu) diff --git a/arch/ppc/syslib/m8xx_setup.c b/arch/ppc/syslib/m8xx_setup.c index 688616de3cde5c..dae9af78bde1ba 100644 --- a/arch/ppc/syslib/m8xx_setup.c +++ b/arch/ppc/syslib/m8xx_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/setup.c - * * Copyright (C) 1995 Linus Torvalds * Adapted from 'alpha' version by Gary Thomas * Modified by Cort Dougan (cort@cs.nmt.edu) @@ -34,6 +32,13 @@ #include <linux/seq_file.h> #include <linux/root_dev.h> +#if defined(CONFIG_MTD) && defined(CONFIG_MTD_PHYSMAP) +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/map.h> +#endif + #include <asm/mmu.h> #include <asm/reg.h> #include <asm/residual.h> @@ -49,6 +54,34 @@ #include "ppc8xx_pic.h" +#ifdef CONFIG_MTD_PHYSMAP +#define MPC8xxADS_BANK_WIDTH 4 +#endif + +#define MPC8xxADS_U_BOOT_SIZE 0x80000 +#define MPC8xxADS_FREE_AREA_OFFSET MPC8xxADS_U_BOOT_SIZE + +#if defined(CONFIG_MTD_PARTITIONS) + /* + NOTE: bank width and interleave relative to the installed flash + should have been chosen within MTD_CFI_GEOMETRY options. + */ +static struct mtd_partition mpc8xxads_partitions[] = { + { + .name = "bootloader", + .size = MPC8xxADS_U_BOOT_SIZE, + .offset = 0, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, { + .name = "User FS", + .offset = MPC8xxADS_FREE_AREA_OFFSET + } +}; + +#define mpc8xxads_part_num (sizeof (mpc8xxads_partitions) / sizeof (mpc8xxads_partitions[0])) + +#endif + static int m8xx_set_rtc_time(unsigned long time); static unsigned long m8xx_get_rtc_time(void); void m8xx_calibrate_decr(void); @@ -71,6 +104,10 @@ board_init(void) void __init m8xx_setup_arch(void) { +#if defined(CONFIG_MTD) && defined(CONFIG_MTD_PHYSMAP) + bd_t *binfo = (bd_t *)__res; +#endif + /* Reset the Communication Processor Module. */ m8xx_cpm_reset(); @@ -106,6 +143,17 @@ m8xx_setup_arch(void) } #endif #endif + +#if defined (CONFIG_MPC86XADS) || defined (CONFIG_MPC885ADS) +#if defined(CONFIG_MTD_PHYSMAP) + physmap_configure(binfo->bi_flashstart, binfo->bi_flashsize, + MPC8xxADS_BANK_WIDTH, NULL); +#ifdef CONFIG_MTD_PARTITIONS + physmap_set_partitions(mpc8xxads_partitions, mpc8xxads_part_num); +#endif /* CONFIG_MTD_PARTITIONS */ +#endif /* CONFIG_MTD_PHYSMAP */ +#endif + board_init(); } @@ -140,9 +188,11 @@ void __init __attribute__ ((weak)) init_internal_rtc(void) { /* Disable the RTC one second and alarm interrupts. */ - out_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc, in_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc) & ~(RTCSC_SIE | RTCSC_ALE)); + clrbits16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc, (RTCSC_SIE | RTCSC_ALE)); + /* Enable the RTC */ - out_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc, in_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc) | (RTCSC_RTF | RTCSC_RTE)); + setbits16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc, (RTCSC_RTF | RTCSC_RTE)); + } /* The decrementer counts at the system (internal) clock frequency divided by @@ -159,8 +209,7 @@ void __init m8xx_calibrate_decr(void) out_be32(&((immap_t *)IMAP_ADDR)->im_clkrstk.cark_sccrk, KAPWR_KEY); /* Force all 8xx processors to use divide by 16 processor clock. */ - out_be32(&((immap_t *)IMAP_ADDR)->im_clkrst.car_sccr, - in_be32(&((immap_t *)IMAP_ADDR)->im_clkrst.car_sccr)|0x02000000); + setbits32(&((immap_t *)IMAP_ADDR)->im_clkrst.car_sccr, 0x02000000); /* Processor frequency is MHz. * The value 'fp' is the number of decrementer ticks per second. */ @@ -239,8 +288,8 @@ m8xx_restart(char *cmd) __volatile__ unsigned char dummy; local_irq_disable(); - out_be32(&((immap_t *)IMAP_ADDR)->im_clkrst.car_plprcr, in_be32(&((immap_t *)IMAP_ADDR)->im_clkrst.car_plprcr) | 0x00000080); + setbits32(&((immap_t *)IMAP_ADDR)->im_clkrst.car_plprcr, 0x00000080); /* Clear the ME bit in MSR to cause checkstop on machine check */ mtmsr(mfmsr() & ~0x1000); @@ -310,8 +359,8 @@ m8xx_init_IRQ(void) i8259_init(0); /* The i8259 cascade interrupt must be level sensitive. */ - out_be32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_siel, in_be32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_siel & ~(0x80000000 >> ISA_BRIDGE_INT))); + clrbits32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_siel, (0x80000000 >> ISA_BRIDGE_INT)); if (setup_irq(ISA_BRIDGE_INT, &mbx_i8259_irqaction)) enable_irq(ISA_BRIDGE_INT); #endif /* CONFIG_PCI */ diff --git a/arch/ppc/syslib/m8xx_wdt.c b/arch/ppc/syslib/m8xx_wdt.c index df6c9557b86a4f..ac11d7bab44384 100644 --- a/arch/ppc/syslib/m8xx_wdt.c +++ b/arch/ppc/syslib/m8xx_wdt.c @@ -41,8 +41,7 @@ static irqreturn_t m8xx_wdt_interrupt(int irq, void *dev, struct pt_regs *regs) m8xx_wdt_reset(); - out_be16(&imap->im_sit.sit_piscr, in_be16(&imap->im_sit.sit_piscr) | PISCR_PS); /* clear irq */ - + setbits16(&imap->im_sit.sit_piscr, PISCR_PS); return IRQ_HANDLED; } diff --git a/arch/ppc/syslib/mpc10x_common.c b/arch/ppc/syslib/mpc10x_common.c index 3e039706bdbcbc..2fc7c4150a1889 100644 --- a/arch/ppc/syslib/mpc10x_common.c +++ b/arch/ppc/syslib/mpc10x_common.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mpc10x_common.c - * * Common routines for the Motorola SPS MPC106, MPC107 and MPC8240 Host bridge, * Mem ctlr, EPIC, etc. * diff --git a/arch/ppc/syslib/mpc52xx_devices.c b/arch/ppc/syslib/mpc52xx_devices.c index da3c74bfdc9271..7487539a4e9295 100644 --- a/arch/ppc/syslib/mpc52xx_devices.c +++ b/arch/ppc/syslib/mpc52xx_devices.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mpc52xx_devices.c - * * Freescale MPC52xx device descriptions * * diff --git a/arch/ppc/syslib/mpc52xx_pci.c b/arch/ppc/syslib/mpc52xx_pci.c index 313c96ec7eb1a6..9ec525f9fe98c9 100644 --- a/arch/ppc/syslib/mpc52xx_pci.c +++ b/arch/ppc/syslib/mpc52xx_pci.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mpc52xx_pci.c - * * PCI code for the Freescale MPC52xx embedded CPU. * * diff --git a/arch/ppc/syslib/mpc52xx_pci.h b/arch/ppc/syslib/mpc52xx_pci.h index 04b509a02530d3..77d47dbba85e20 100644 --- a/arch/ppc/syslib/mpc52xx_pci.h +++ b/arch/ppc/syslib/mpc52xx_pci.h @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mpc52xx_pci.h - * * PCI Include file the Freescale MPC52xx embedded cpu chips * * diff --git a/arch/ppc/syslib/mpc52xx_pic.c b/arch/ppc/syslib/mpc52xx_pic.c index 4c4497e62517da..c4406f9dc6a3d0 100644 --- a/arch/ppc/syslib/mpc52xx_pic.c +++ b/arch/ppc/syslib/mpc52xx_pic.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mpc52xx_pic.c - * * Programmable Interrupt Controller functions for the Freescale MPC52xx * embedded CPU. * diff --git a/arch/ppc/syslib/mpc52xx_setup.c b/arch/ppc/syslib/mpc52xx_setup.c index a4a4b02227df6c..2ee48ce0a517f8 100644 --- a/arch/ppc/syslib/mpc52xx_setup.c +++ b/arch/ppc/syslib/mpc52xx_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mpc52xx_setup.c - * * Common code for the boards based on Freescale MPC52xx embedded CPU. * * diff --git a/arch/ppc/syslib/mpc52xx_sys.c b/arch/ppc/syslib/mpc52xx_sys.c index 9a0f90aa8aac8e..b4e6f978f05795 100644 --- a/arch/ppc/syslib/mpc52xx_sys.c +++ b/arch/ppc/syslib/mpc52xx_sys.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mpc52xx_sys.c - * * Freescale MPC52xx system descriptions * * diff --git a/arch/ppc/syslib/mpc83xx_devices.c b/arch/ppc/syslib/mpc83xx_devices.c index f9b95de70e2302..1af2c000fcfa6e 100644 --- a/arch/ppc/syslib/mpc83xx_devices.c +++ b/arch/ppc/syslib/mpc83xx_devices.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/83xx/mpc83xx_devices.c - * * MPC83xx Device descriptions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/mpc83xx_sys.c b/arch/ppc/syslib/mpc83xx_sys.c index 82cf3ab77f4a67..0498ae7e01e341 100644 --- a/arch/ppc/syslib/mpc83xx_sys.c +++ b/arch/ppc/syslib/mpc83xx_sys.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/83xx/mpc83xx_sys.c - * * MPC83xx System descriptions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/mpc85xx_devices.c b/arch/ppc/syslib/mpc85xx_devices.c index 00e9b6ff2f6e39..7735336f5b8f51 100644 --- a/arch/ppc/syslib/mpc85xx_devices.c +++ b/arch/ppc/syslib/mpc85xx_devices.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/mpc85xx_devices.c - * * MPC85xx Device descriptions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/mpc85xx_sys.c b/arch/ppc/syslib/mpc85xx_sys.c index 397cfbcce5ea10..d96a93dbcb5a48 100644 --- a/arch/ppc/syslib/mpc85xx_sys.c +++ b/arch/ppc/syslib/mpc85xx_sys.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/85xx/mpc85xx_sys.c - * * MPC85xx System descriptions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/mpc8xx_devices.c b/arch/ppc/syslib/mpc8xx_devices.c index 92dc98b36bdeff..bd41ed83beb357 100644 --- a/arch/ppc/syslib/mpc8xx_devices.c +++ b/arch/ppc/syslib/mpc8xx_devices.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mpc8xx_devices.c - * * MPC8xx Device descriptions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/mpc8xx_sys.c b/arch/ppc/syslib/mpc8xx_sys.c index d3c61752160398..eee2132848559c 100644 --- a/arch/ppc/syslib/mpc8xx_sys.c +++ b/arch/ppc/syslib/mpc8xx_sys.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/mpc8xx_sys.c - * * MPC8xx System descriptions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/mv64360_pic.c b/arch/ppc/syslib/mv64360_pic.c index 58b0aa813e85e5..5a19697060f029 100644 --- a/arch/ppc/syslib/mv64360_pic.c +++ b/arch/ppc/syslib/mv64360_pic.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/mv64360_pic.c - * * Interrupt controller support for Marvell's MV64360. * * Author: Rabeeh Khoury <rabeeh@galileo.co.il> diff --git a/arch/ppc/syslib/mv64x60.c b/arch/ppc/syslib/mv64x60.c index 1f01b7e2376b97..3b039c30a439ad 100644 --- a/arch/ppc/syslib/mv64x60.c +++ b/arch/ppc/syslib/mv64x60.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mv64x60.c - * * Common routines for the Marvell/Galileo Discovery line of host bridges * (gt64260, mv64360, mv64460, ...). * diff --git a/arch/ppc/syslib/mv64x60_dbg.c b/arch/ppc/syslib/mv64x60_dbg.c index fa5b2e45e0ca54..9cf18764a1a145 100644 --- a/arch/ppc/syslib/mv64x60_dbg.c +++ b/arch/ppc/syslib/mv64x60_dbg.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mv64x60_dbg.c - * * KGDB and progress routines for the Marvell/Galileo MV64x60 (Discovery). * * Author: Mark A. Greer <mgreer@mvista.com> diff --git a/arch/ppc/syslib/mv64x60_win.c b/arch/ppc/syslib/mv64x60_win.c index 5b827e2bbe22f4..4bf1ad17bf1a6b 100644 --- a/arch/ppc/syslib/mv64x60_win.c +++ b/arch/ppc/syslib/mv64x60_win.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/mv64x60_win.c - * * Tables with info on how to manipulate the 32 & 64 bit windows on the * various types of Marvell bridge chips. * diff --git a/arch/ppc/syslib/open_pic.c b/arch/ppc/syslib/open_pic.c index 894779712b4614..38e5b93fbe41f0 100644 --- a/arch/ppc/syslib/open_pic.c +++ b/arch/ppc/syslib/open_pic.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/open_pic.c -- OpenPIC Interrupt Handling - * * Copyright (C) 1997 Geert Uytterhoeven * * This file is subject to the terms and conditions of the GNU General Public diff --git a/arch/ppc/syslib/open_pic2.c b/arch/ppc/syslib/open_pic2.c index 1c40049b9a45b3..bcbe40de26fe51 100644 --- a/arch/ppc/syslib/open_pic2.c +++ b/arch/ppc/syslib/open_pic2.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/open_pic.c -- OpenPIC Interrupt Handling - * * Copyright (C) 1997 Geert Uytterhoeven * * This file is subject to the terms and conditions of the GNU General Public diff --git a/arch/ppc/syslib/open_pic_defs.h b/arch/ppc/syslib/open_pic_defs.h index 6c94e713146353..3a25de7cb57287 100644 --- a/arch/ppc/syslib/open_pic_defs.h +++ b/arch/ppc/syslib/open_pic_defs.h @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/open_pic_defs.h -- OpenPIC definitions - * * Copyright (C) 1997 Geert Uytterhoeven * * This file is based on the following documentation: diff --git a/arch/ppc/syslib/pci_auto.c b/arch/ppc/syslib/pci_auto.c index d64207c2a972e3..ee20a86fcc4ba5 100644 --- a/arch/ppc/syslib/pci_auto.c +++ b/arch/ppc/syslib/pci_auto.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/pci_auto.c - * * PCI autoconfiguration library * * Author: Matt Porter <mporter@mvista.com> diff --git a/arch/ppc/syslib/ppc4xx_dma.c b/arch/ppc/syslib/ppc4xx_dma.c index 05ccd598dd4ec7..b40b96a8c609ad 100644 --- a/arch/ppc/syslib/ppc4xx_dma.c +++ b/arch/ppc/syslib/ppc4xx_dma.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/ppc4xx_dma.c - * * IBM PPC4xx DMA engine core library * * Copyright 2000-2004 MontaVista Software Inc. diff --git a/arch/ppc/syslib/ppc4xx_pic.c b/arch/ppc/syslib/ppc4xx_pic.c index aa4165144ec274..fd9af0fc0e9f43 100644 --- a/arch/ppc/syslib/ppc4xx_pic.c +++ b/arch/ppc/syslib/ppc4xx_pic.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ppc4xx_pic.c - * * Interrupt controller driver for PowerPC 4xx-based processors. * * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> diff --git a/arch/ppc/syslib/ppc4xx_pm.c b/arch/ppc/syslib/ppc4xx_pm.c deleted file mode 100644 index 60a479204885cb..00000000000000 --- a/arch/ppc/syslib/ppc4xx_pm.c +++ /dev/null @@ -1,47 +0,0 @@ -/* - * Author: Armin Kuster <akuster@mvista.com> - * - * 2002 (c) MontaVista, Software, Inc. This file is licensed under - * the terms of the GNU General Public License version 2. This program - * is licensed "as is" without any warranty of any kind, whether express - * or implied. - * - * This an attempt to get Power Management going for the IBM 4xx processor. - * This was derived from the ppc4xx._setup.c file - */ - -#include <linux/config.h> -#include <linux/init.h> - -#include <asm/ibm4xx.h> - -void __init -ppc4xx_pm_init(void) -{ - - unsigned int value = 0; - - /* turn off unused hardware to save power */ -#ifdef CONFIG_405GP - value |= CPM_DCP; /* CodePack */ -#endif - -#if !defined(CONFIG_IBM_OCP_GPIO) - value |= CPM_GPIO0; -#endif - -#if !defined(CONFIG_PPC405_I2C_ADAP) - value |= CPM_IIC0; -#ifdef CONFIG_STB03xxx - value |= CPM_IIC1; -#endif -#endif - - -#if !defined(CONFIG_405_DMA) - value |= CPM_DMA; -#endif - - mtdcr(DCRN_CPMFR, value); - -} diff --git a/arch/ppc/syslib/ppc4xx_sgdma.c b/arch/ppc/syslib/ppc4xx_sgdma.c index 9f76e8ee39edc4..280ea010a9c8e7 100644 --- a/arch/ppc/syslib/ppc4xx_sgdma.c +++ b/arch/ppc/syslib/ppc4xx_sgdma.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/ppc4xx_sgdma.c - * * IBM PPC4xx DMA engine scatter/gather library * * Copyright 2002-2003 MontaVista Software Inc. diff --git a/arch/ppc/syslib/ppc83xx_setup.c b/arch/ppc/syslib/ppc83xx_setup.c index 7bada82527a892..26afd637dc8180 100644 --- a/arch/ppc/syslib/ppc83xx_setup.c +++ b/arch/ppc/syslib/ppc83xx_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ppc83xx_setup.c - * * MPC83XX common board code * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/ppc83xx_setup.h b/arch/ppc/syslib/ppc83xx_setup.h index a122a7322e5eed..478b011cd96330 100644 --- a/arch/ppc/syslib/ppc83xx_setup.h +++ b/arch/ppc/syslib/ppc83xx_setup.h @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ppc83xx_setup.h - * * MPC83XX common board definitions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/ppc85xx_common.c b/arch/ppc/syslib/ppc85xx_common.c index 19ad537225e434..0145c968f9adf7 100644 --- a/arch/ppc/syslib/ppc85xx_common.c +++ b/arch/ppc/syslib/ppc85xx_common.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ppc85xx_common.c - * * MPC85xx support routines * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/ppc85xx_common.h b/arch/ppc/syslib/ppc85xx_common.h index 94edf32151dda0..182744a1321c3d 100644 --- a/arch/ppc/syslib/ppc85xx_common.h +++ b/arch/ppc/syslib/ppc85xx_common.h @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ppc85xx_common.h - * * MPC85xx support routines * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/ppc85xx_setup.c b/arch/ppc/syslib/ppc85xx_setup.c index e4dda43fdaa7bb..e70b34ee627519 100644 --- a/arch/ppc/syslib/ppc85xx_setup.c +++ b/arch/ppc/syslib/ppc85xx_setup.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ppc85xx_setup.c - * * MPC85XX common board code * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/ppc85xx_setup.h b/arch/ppc/syslib/ppc85xx_setup.h index e340b0545fb5e2..f55b8032d3d946 100644 --- a/arch/ppc/syslib/ppc85xx_setup.h +++ b/arch/ppc/syslib/ppc85xx_setup.h @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ppc85xx_setup.h - * * MPC85XX common board definitions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/ppc_sys.c b/arch/ppc/syslib/ppc_sys.c index c0b93c4191eeac..60c724e1158499 100644 --- a/arch/ppc/syslib/ppc_sys.c +++ b/arch/ppc/syslib/ppc_sys.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/ppc_sys.c - * * PPC System library functions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> @@ -15,11 +13,22 @@ */ #include <linux/string.h> +#include <linux/bootmem.h> #include <asm/ppc_sys.h> int (*ppc_sys_device_fixup) (struct platform_device * pdev); static int ppc_sys_inited; +static int ppc_sys_func_inited; + +static const char *ppc_sys_func_names[] = { + [PPC_SYS_FUNC_DUMMY] = "dummy", + [PPC_SYS_FUNC_ETH] = "eth", + [PPC_SYS_FUNC_UART] = "uart", + [PPC_SYS_FUNC_HLDC] = "hldc", + [PPC_SYS_FUNC_USB] = "usb", + [PPC_SYS_FUNC_IRDA] = "irda", +}; void __init identify_ppc_sys_by_id(u32 id) { @@ -38,13 +47,13 @@ void __init identify_ppc_sys_by_id(u32 id) void __init identify_ppc_sys_by_name(char *name) { unsigned int i = 0; - while (ppc_sys_specs[i].ppc_sys_name[0]) - { + while (ppc_sys_specs[i].ppc_sys_name[0]) { if (!strcmp(ppc_sys_specs[i].ppc_sys_name, name)) break; i++; } cur_ppc_sys_spec = &ppc_sys_specs[i]; + return; } @@ -128,6 +137,165 @@ void ppc_sys_device_remove(enum ppc_sys_devices dev) } } +/* Platform-notify mapping + * Helper function for BSP code to assign board-specific platfom-divice bits + */ + +void platform_notify_map(const struct platform_notify_dev_map *map, + struct device *dev) +{ + struct platform_device *pdev; + int len, idx; + const char *s; + + /* do nothing if no device or no bus_id */ + if (!dev || !dev->bus_id) + return; + + /* call per device map */ + while (map->bus_id != NULL) { + idx = -1; + s = strrchr(dev->bus_id, '.'); + if (s != NULL) + idx = (int)simple_strtol(s + 1, NULL, 10); + else + s = dev->bus_id; + + len = s - dev->bus_id; + + if (!strncmp(dev->bus_id, map->bus_id, len)) { + pdev = container_of(dev, struct platform_device, dev); + map->rtn(pdev, idx); + } + map++; + } +} + +/* + Function assignment stuff. + Intended to work as follows: + the device name defined in foo_devices.c will be concatenated with :"func", + where func is string map of respective function from platfom_device_func enum + + The PPC_SYS_FUNC_DUMMY function is intended to remove all assignments, making the device to appear + in platform bus with unmodified name. + */ + +/* + Here we'll replace .name pointers with fixed-lenght strings + Hereby, this should be called *before* any func stuff triggeded. + */ +void ppc_sys_device_initfunc(void) +{ + int i; + const char *name; + static char new_names[NUM_PPC_SYS_DEVS][BUS_ID_SIZE]; + enum ppc_sys_devices cur_dev; + + /* If inited yet, do nothing */ + if (ppc_sys_func_inited) + return; + + for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) { + if ((cur_dev = cur_ppc_sys_spec->device_list[i]) < 0) + continue; + + if (ppc_sys_platform_devices[cur_dev].name) { + /*backup name */ + name = ppc_sys_platform_devices[cur_dev].name; + strlcpy(new_names[i], name, BUS_ID_SIZE); + ppc_sys_platform_devices[cur_dev].name = new_names[i]; + } + } + + ppc_sys_func_inited = 1; +} + +/*The "engine" of the func stuff. Here we either concat specified function string description + to the name, or remove it if PPC_SYS_FUNC_DUMMY parameter is passed here*/ +void ppc_sys_device_setfunc(enum ppc_sys_devices dev, + enum platform_device_func func) +{ + char *s; + char *name = (char *)ppc_sys_platform_devices[dev].name; + char tmp[BUS_ID_SIZE]; + + if (!ppc_sys_func_inited) { + printk(KERN_ERR "Unable to alter function - not inited!\n"); + return; + } + + if (ppc_sys_inited) { + platform_device_unregister(&ppc_sys_platform_devices[dev]); + } + + if ((s = (char *)strchr(name, ':')) != NULL) { /* reassign */ + /* Either change the name after ':' or remove func modifications */ + if (func != PPC_SYS_FUNC_DUMMY) + strlcpy(s + 1, ppc_sys_func_names[func], BUS_ID_SIZE); + else + *s = 0; + } else if (func != PPC_SYS_FUNC_DUMMY) { + /* do assignment if it is not just "clear" request */ + sprintf(tmp, "%s:%s", name, ppc_sys_func_names[func]); + strlcpy(name, tmp, BUS_ID_SIZE); + } + + if (ppc_sys_inited) { + platform_device_register(&ppc_sys_platform_devices[dev]); + } +} + +void ppc_sys_device_disable(enum ppc_sys_devices dev) +{ + BUG_ON(cur_ppc_sys_spec == NULL); + + /*Check if it is enabled*/ + if(!(cur_ppc_sys_spec->config[dev] & PPC_SYS_CONFIG_DISABLED)) { + if (ppc_sys_inited) { + platform_device_unregister(&ppc_sys_platform_devices[dev]); + } + cur_ppc_sys_spec->config[dev] |= PPC_SYS_CONFIG_DISABLED; + } +} + +void ppc_sys_device_enable(enum ppc_sys_devices dev) +{ + BUG_ON(cur_ppc_sys_spec == NULL); + + /*Check if it is disabled*/ + if(cur_ppc_sys_spec->config[dev] & PPC_SYS_CONFIG_DISABLED) { + if (ppc_sys_inited) { + platform_device_register(&ppc_sys_platform_devices[dev]); + } + cur_ppc_sys_spec->config[dev] &= ~PPC_SYS_CONFIG_DISABLED; + } + +} + +void ppc_sys_device_enable_all(void) +{ + enum ppc_sys_devices cur_dev; + int i; + + for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) { + cur_dev = cur_ppc_sys_spec->device_list[i]; + ppc_sys_device_enable(cur_dev); + } +} + +void ppc_sys_device_disable_all(void) +{ + enum ppc_sys_devices cur_dev; + int i; + + for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) { + cur_dev = cur_ppc_sys_spec->device_list[i]; + ppc_sys_device_disable(cur_dev); + } +} + + static int __init ppc_sys_init(void) { unsigned int i, dev_id, ret = 0; @@ -136,7 +304,8 @@ static int __init ppc_sys_init(void) for (i = 0; i < cur_ppc_sys_spec->num_devices; i++) { dev_id = cur_ppc_sys_spec->device_list[i]; - if (dev_id != -1) { + if ((dev_id != -1) && + !(cur_ppc_sys_spec->config[dev_id] & PPC_SYS_CONFIG_DISABLED)) { if (ppc_sys_device_fixup != NULL) ppc_sys_device_fixup(&ppc_sys_platform_devices [dev_id]); diff --git a/arch/ppc/syslib/pq2_devices.c b/arch/ppc/syslib/pq2_devices.c index 6ff3aab82fc337..0636aed7b8271b 100644 --- a/arch/ppc/syslib/pq2_devices.c +++ b/arch/ppc/syslib/pq2_devices.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/pq2_devices.c - * * PQ2 Device descriptions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/pq2_sys.c b/arch/ppc/syslib/pq2_sys.c index 36d6e217994019..75e64f1c144d7f 100644 --- a/arch/ppc/syslib/pq2_sys.c +++ b/arch/ppc/syslib/pq2_sys.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/pq2_devices.c - * * PQ2 System descriptions * * Maintainer: Kumar Gala <galak@kernel.crashing.org> diff --git a/arch/ppc/syslib/prep_nvram.c b/arch/ppc/syslib/prep_nvram.c index 2c6364d9641fa4..474dccbc4a8a9e 100644 --- a/arch/ppc/syslib/prep_nvram.c +++ b/arch/ppc/syslib/prep_nvram.c @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/prep_nvram.c - * * Copyright (C) 1998 Corey Minyard * * This reads the NvRAM on PReP compliant machines (generally from IBM or diff --git a/arch/ppc/syslib/todc_time.c b/arch/ppc/syslib/todc_time.c index 1323c641c19d6e..a8168b8e5683b1 100644 --- a/arch/ppc/syslib/todc_time.c +++ b/arch/ppc/syslib/todc_time.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/todc_time.c - * * Time of Day Clock support for the M48T35, M48T37, M48T59, and MC146818 * Real Time Clocks/Timekeepers. * diff --git a/arch/ppc/syslib/xilinx_pic.c b/arch/ppc/syslib/xilinx_pic.c index 47f04c71fe9c02..e672b600f31549 100644 --- a/arch/ppc/syslib/xilinx_pic.c +++ b/arch/ppc/syslib/xilinx_pic.c @@ -1,6 +1,4 @@ /* - * arch/ppc/syslib/xilinx_pic.c - * * Interrupt controller driver for Xilinx Virtex-II Pro. * * Author: MontaVista Software, Inc. @@ -15,7 +13,7 @@ #include <linux/init.h> #include <linux/irq.h> #include <asm/io.h> -#include <asm/xparameters.h> +#include <platforms/4xx/xparameters/xparameters.h> #include <asm/ibm4xx.h> #include <asm/machdep.h> diff --git a/drivers/char/hvcs.c b/drivers/char/hvcs.c index 831eb4e8d9d372..f7ac31856572a1 100644 --- a/drivers/char/hvcs.c +++ b/drivers/char/hvcs.c @@ -118,7 +118,7 @@ * the hvcs_final_close() function in order to get it out of the spinlock. * Rearranged hvcs_close(). Cleaned up some printks and did some housekeeping * on the changelog. Removed local CLC_LENGTH and used HVCS_CLC_LENGTH from - * arch/ppc64/hvcserver.h. + * include/asm-powerpc/hvcserver.h * * 1.3.2 -> 1.3.3 Replaced yield() in hvcs_close() with tty_wait_until_sent() to * prevent possible lockup with realtime scheduling as similarily pointed out by @@ -168,9 +168,10 @@ MODULE_VERSION(HVCS_DRIVER_VERSION); /* * The hcall interface involves putting 8 chars into each of two registers. - * We load up those 2 registers (in arch/ppc64/hvconsole.c) by casting char[16] - * to long[2]. It would work without __ALIGNED__, but a little (tiny) bit - * slower because an unaligned load is slower than aligned load. + * We load up those 2 registers (in arch/powerpc/platforms/pseries/hvconsole.c) + * by casting char[16] to long[2]. It would work without __ALIGNED__, but a + * little (tiny) bit slower because an unaligned load is slower than aligned + * load. */ #define __ALIGNED__ __attribute__((__aligned__(8))) diff --git a/include/asm-powerpc/firmware.h b/include/asm-powerpc/firmware.h index f804b34cf06a6f..b7791a1b05db87 100644 --- a/include/asm-powerpc/firmware.h +++ b/include/asm-powerpc/firmware.h @@ -89,15 +89,6 @@ static inline unsigned long firmware_has_feature(unsigned long feature) (FW_FEATURE_POSSIBLE & ppc64_firmware_features & feature); } -#ifdef CONFIG_PPC_PSERIES -typedef struct { - unsigned long val; - char * name; -} firmware_feature_t; - -extern firmware_feature_t firmware_features_table[]; -#endif - extern void system_reset_fwnmi(void); extern void machine_check_fwnmi(void); diff --git a/include/asm-powerpc/lmb.h b/include/asm-powerpc/lmb.h index d3546c4c9f4607..377ac1b23aa323 100644 --- a/include/asm-powerpc/lmb.h +++ b/include/asm-powerpc/lmb.h @@ -19,8 +19,6 @@ #define MAX_LMB_REGIONS 128 -#define LMB_ALLOC_ANYWHERE 0 - struct lmb_property { unsigned long base; unsigned long size; @@ -43,15 +41,16 @@ extern struct lmb lmb; extern void __init lmb_init(void); extern void __init lmb_analyze(void); -extern long __init lmb_add(unsigned long, unsigned long); -extern long __init lmb_reserve(unsigned long, unsigned long); -extern unsigned long __init lmb_alloc(unsigned long, unsigned long); -extern unsigned long __init lmb_alloc_base(unsigned long, unsigned long, - unsigned long); +extern long __init lmb_add(unsigned long base, unsigned long size); +extern long __init lmb_reserve(unsigned long base, unsigned long size); +extern unsigned long __init lmb_alloc(unsigned long size, unsigned long align); +extern unsigned long __init lmb_alloc_base(unsigned long size, + unsigned long align, unsigned long max_addr); +extern unsigned long __init __lmb_alloc_base(unsigned long size, + unsigned long align, unsigned long max_addr); extern unsigned long __init lmb_phys_mem_size(void); extern unsigned long __init lmb_end_of_DRAM(void); -extern unsigned long __init lmb_abs_to_phys(unsigned long); -extern void __init lmb_enforce_memory_limit(unsigned long); +extern void __init lmb_enforce_memory_limit(unsigned long memory_limit); extern void lmb_dump_all(void); diff --git a/include/asm-powerpc/paca.h b/include/asm-powerpc/paca.h index c9add8f1ad94b1..ec94b51074fcf7 100644 --- a/include/asm-powerpc/paca.h +++ b/include/asm-powerpc/paca.h @@ -54,7 +54,7 @@ struct paca_struct { #endif /* CONFIG_PPC_ISERIES */ /* - * MAGIC: the spinlock functions in arch/ppc64/lib/locks.c + * MAGIC: the spinlock functions in arch/powerpc/lib/locks.c * load lock_token and paca_index with a single lwz * instruction. They must travel together and be properly * aligned. diff --git a/include/asm-powerpc/rwsem.h b/include/asm-powerpc/rwsem.h index 79bae4933b73a2..2c2fe9647595bd 100644 --- a/include/asm-powerpc/rwsem.h +++ b/include/asm-powerpc/rwsem.h @@ -4,7 +4,7 @@ #ifdef __KERNEL__ /* - * include/asm-ppc64/rwsem.h: R/W semaphores for PPC using the stuff + * include/asm-powerpc/rwsem.h: R/W semaphores for PPC using the stuff * in lib/rwsem.c. Adapted largely from include/asm-i386/rwsem.h * by Paul Mackerras <paulus@samba.org>. */ diff --git a/include/asm-ppc/harrier.h b/include/asm-ppc/harrier.h index 36c73ab7e43e6a..7acd7fc126ecac 100644 --- a/include/asm-ppc/harrier.h +++ b/include/asm-ppc/harrier.h @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/harrier.h - * * Definitions for Motorola MCG Harrier North Bridge & Memory controller * * Author: Dale Farnsworth diff --git a/include/asm-ppc/ibm44x.h b/include/asm-ppc/ibm44x.h index f835066fb3cad4..3acc382cc83f3f 100644 --- a/include/asm-ppc/ibm44x.h +++ b/include/asm-ppc/ibm44x.h @@ -29,7 +29,7 @@ /* TLB entry offset/size used for pinning kernel lowmem */ #define PPC44x_PIN_SHIFT 28 -#define PPC44x_PIN_SIZE (1 << PPC44x_PIN_SHIFT) +#define PPC_PIN_SIZE (1 << PPC44x_PIN_SHIFT) /* Lowest TLB slot consumed by the default pinned TLBs */ #define PPC44x_LOW_SLOT 63 diff --git a/include/asm-ppc/ibm4xx.h b/include/asm-ppc/ibm4xx.h index 6c28ae7807f4fe..38f99710752b1f 100644 --- a/include/asm-ppc/ibm4xx.h +++ b/include/asm-ppc/ibm4xx.h @@ -51,6 +51,10 @@ #include <platforms/4xx/xilinx_ml300.h> #endif +#if defined(CONFIG_XILINX_ML403) +#include <platforms/4xx/xilinx_ml403.h> +#endif + #ifndef __ASSEMBLY__ #ifdef CONFIG_40x diff --git a/include/asm-ppc/io.h b/include/asm-ppc/io.h index df9cf6ed189d6b..b919d8fb7d98b8 100644 --- a/include/asm-ppc/io.h +++ b/include/asm-ppc/io.h @@ -575,4 +575,11 @@ extern void pci_iounmap(struct pci_dev *dev, void __iomem *); */ #define xlate_dev_kmem_ptr(p) p +/* access ports */ +#define setbits32(_addr, _v) out_be32((_addr), in_be32(_addr) | (_v)) +#define clrbits32(_addr, _v) out_be32((_addr), in_be32(_addr) & ~(_v)) + +#define setbits16(_addr, _v) out_be16((_addr), in_be16(_addr) | (_v)) +#define clrbits16(_addr, _v) out_be16((_addr), in_be16(_addr) & ~(_v)) + #endif /* __KERNEL__ */ diff --git a/include/asm-ppc/mpc10x.h b/include/asm-ppc/mpc10x.h index 77b1e092c206d1..b30a6a3b5bd20a 100644 --- a/include/asm-ppc/mpc10x.h +++ b/include/asm-ppc/mpc10x.h @@ -1,6 +1,4 @@ /* - * arch/ppc/kernel/mpc10x.h - * * Common routines for the Motorola SPS MPC106/8240/107 Host bridge/Mem * ctlr/EPIC/etc. * @@ -165,6 +163,7 @@ enum ppc_sys_devices { MPC10X_DMA1, MPC10X_UART0, MPC10X_UART1, + NUM_PPC_SYS_DEVS, }; int mpc10x_bridge_init(struct pci_controller *hose, diff --git a/include/asm-ppc/mpc52xx.h b/include/asm-ppc/mpc52xx.h index a055e0756b9d85..6167f74635f733 100644 --- a/include/asm-ppc/mpc52xx.h +++ b/include/asm-ppc/mpc52xx.h @@ -60,6 +60,7 @@ enum ppc_sys_devices { MPC52xx_ATA, MPC52xx_I2C1, MPC52xx_I2C2, + NUM_PPC_SYS_DEVS, }; diff --git a/include/asm-ppc/mpc8260.h b/include/asm-ppc/mpc8260.h index 321452695039ac..6ba69a86b9ddf2 100644 --- a/include/asm-ppc/mpc8260.h +++ b/include/asm-ppc/mpc8260.h @@ -83,6 +83,7 @@ enum ppc_sys_devices { MPC82xx_CPM_SMC2, MPC82xx_CPM_USB, MPC82xx_SEC1, + NUM_PPC_SYS_DEVS, }; #ifndef __ASSEMBLY__ diff --git a/include/asm-ppc/mpc83xx.h b/include/asm-ppc/mpc83xx.h index 7cdf60fa69b63a..3c23fc43bfbc47 100644 --- a/include/asm-ppc/mpc83xx.h +++ b/include/asm-ppc/mpc83xx.h @@ -108,6 +108,7 @@ enum ppc_sys_devices { MPC83xx_USB2_DR, MPC83xx_USB2_MPH, MPC83xx_MDIO, + NUM_PPC_SYS_DEVS, }; #endif /* CONFIG_83xx */ diff --git a/include/asm-ppc/mpc85xx.h b/include/asm-ppc/mpc85xx.h index c8a96aa44fb7c9..f47002a60edf59 100644 --- a/include/asm-ppc/mpc85xx.h +++ b/include/asm-ppc/mpc85xx.h @@ -139,6 +139,7 @@ enum ppc_sys_devices { MPC85xx_eTSEC4, MPC85xx_IIC2, MPC85xx_MDIO, + NUM_PPC_SYS_DEVS, }; /* Internal interrupts are all Level Sensitive, and Positive Polarity */ diff --git a/include/asm-ppc/mpc8xx.h b/include/asm-ppc/mpc8xx.h index 46f159cf589e96..3515a7fa6c8939 100644 --- a/include/asm-ppc/mpc8xx.h +++ b/include/asm-ppc/mpc8xx.h @@ -111,8 +111,11 @@ enum ppc_sys_devices { MPC8xx_CPM_SMC1, MPC8xx_CPM_SMC2, MPC8xx_CPM_USB, + NUM_PPC_SYS_DEVS, }; +#define PPC_PIN_SIZE (24 * 1024 * 1024) /* 24Mbytes of data pinned */ + #ifndef BOARD_CHIP_NAME #define BOARD_CHIP_NAME "" #endif diff --git a/include/asm-ppc/pgtable.h b/include/asm-ppc/pgtable.h index 6d1c39e8a6afef..e1c62da12e74a5 100644 --- a/include/asm-ppc/pgtable.h +++ b/include/asm-ppc/pgtable.h @@ -12,6 +12,7 @@ #include <asm/processor.h> /* For TASK_SIZE */ #include <asm/mmu.h> #include <asm/page.h> +#include <asm/io.h> /* For sub-arch specific PPC_PIN_SIZE */ struct mm_struct; extern unsigned long va_to_phys(unsigned long address); @@ -127,9 +128,8 @@ extern unsigned long ioremap_bot, ioremap_base; * of RAM. -- Cort */ #define VMALLOC_OFFSET (0x1000000) /* 16M */ -#ifdef CONFIG_44x -#include <asm/ibm44x.h> -#define VMALLOC_START (((_ALIGN((long)high_memory, PPC44x_PIN_SIZE) + VMALLOC_OFFSET) & ~(VMALLOC_OFFSET-1))) +#ifdef PPC_PIN_SIZE +#define VMALLOC_START (((_ALIGN((long)high_memory, PPC_PIN_SIZE) + VMALLOC_OFFSET) & ~(VMALLOC_OFFSET-1))) #else #define VMALLOC_START ((((long)high_memory + VMALLOC_OFFSET) & ~(VMALLOC_OFFSET-1))) #endif diff --git a/include/asm-ppc/ppc_sys.h b/include/asm-ppc/ppc_sys.h index 83d8c77c124df3..4b94f7059ebec5 100644 --- a/include/asm-ppc/ppc_sys.h +++ b/include/asm-ppc/ppc_sys.h @@ -33,6 +33,8 @@ #include <asm/mpc52xx.h> #elif defined(CONFIG_MPC10X_BRIDGE) #include <asm/mpc10x.h> +#elif defined(CONFIG_XILINX_VIRTEX) +#include <platforms/4xx/virtex.h> #else #error "need definition of ppc_sys_devices" #endif @@ -44,9 +46,26 @@ struct ppc_sys_spec { u32 value; u32 num_devices; char *ppc_sys_name; + u8 config[NUM_PPC_SYS_DEVS]; enum ppc_sys_devices *device_list; }; +struct platform_notify_dev_map { + const char *bus_id; + void (*rtn)(struct platform_device * pdev, int idx); +}; + +enum platform_device_func { + PPC_SYS_FUNC_DUMMY = 0, + PPC_SYS_FUNC_ETH = 1, + PPC_SYS_FUNC_UART = 2, + PPC_SYS_FUNC_HLDC = 3, + PPC_SYS_FUNC_USB = 4, + PPC_SYS_FUNC_IRDA = 5, +}; + +#define PPC_SYS_CONFIG_DISABLED 1 + /* describes all specific chips and which devices they have on them */ extern struct ppc_sys_spec ppc_sys_specs[]; extern struct ppc_sys_spec *cur_ppc_sys_spec; @@ -72,5 +91,20 @@ extern void *ppc_sys_get_pdata(enum ppc_sys_devices dev) __init; /* remove a device from the system */ extern void ppc_sys_device_remove(enum ppc_sys_devices dev); +/* Function assignment stuff */ +void ppc_sys_device_initfunc(void); +void ppc_sys_device_setfunc(enum ppc_sys_devices dev, + enum platform_device_func func); +void ppc_sys_device_set_func_all(enum platform_device_func func); + +void platform_notify_map(const struct platform_notify_dev_map *map, + struct device *dev); + +/* Enable / disable stuff */ +void ppc_sys_device_disable(enum ppc_sys_devices dev); +void ppc_sys_device_enable(enum ppc_sys_devices dev); +void ppc_sys_device_enable_all(void); +void ppc_sys_device_disable_all(void); + #endif /* __ASM_PPC_SYS_H */ #endif /* __KERNEL__ */ diff --git a/include/asm-ppc/todc.h b/include/asm-ppc/todc.h index 84bae7d7681451..937c7dbe6e5c89 100644 --- a/include/asm-ppc/todc.h +++ b/include/asm-ppc/todc.h @@ -1,6 +1,4 @@ /* - * include/asm-ppc/todc.h - * * Definitions for the M48Txx and mc146818 series of Time of day/Real Time * Clock chips. * diff --git a/include/asm-ppc/xparameters.h b/include/asm-ppc/xparameters.h deleted file mode 100644 index fe4eac6291393d..00000000000000 --- a/include/asm-ppc/xparameters.h +++ /dev/null @@ -1,18 +0,0 @@ -/* - * include/asm-ppc/xparameters.h - * - * This file includes the correct xparameters.h for the CONFIG'ed board - * - * Author: MontaVista Software, Inc. - * source@mvista.com - * - * 2004 (c) MontaVista Software, Inc. This file is licensed under the terms - * of the GNU General Public License version 2. This program is licensed - * "as is" without any warranty of any kind, whether express or implied. - */ - -#include <linux/config.h> - -#if defined(CONFIG_XILINX_ML300) -#include <platforms/4xx/xparameters/xparameters_ml300.h> -#endif diff --git a/kernel/auditsc.c b/kernel/auditsc.c index d7e7e637b92abc..c4394abcd5e695 100644 --- a/kernel/auditsc.c +++ b/kernel/auditsc.c @@ -958,7 +958,7 @@ void audit_syscall_entry(struct task_struct *tsk, int arch, int major, * * i386 no * x86_64 no - * ppc64 yes (see arch/ppc64/kernel/misc.S) + * ppc64 yes (see arch/powerpc/platforms/iseries/misc.S) * * This also happens with vm86 emulation in a non-nested manner * (entries without exits), so this case must be caught. diff --git a/lib/extable.c b/lib/extable.c index 18df57c029df1d..01c08b5836f5e8 100644 --- a/lib/extable.c +++ b/lib/extable.c @@ -1,5 +1,4 @@ /* - * lib/extable.c * Derived from arch/ppc/mm/extable.c and arch/i386/mm/extable.c. * * Copyright (C) 2004 Paul Mackerras, IBM Corp. |