The Userspace I/O HOWTO

If you know of any translations for this document, or you are interested in translating it, please email me <hjk@linutronix.de>.

For many types of devices, creating a Linux kernel driver is overkill. All that is really needed is some way to handle an interrupt and provide access to the memory space of the device. The logic of controlling the device does not necessarily have to be within the kernel, as the device does not need to take advantage of any of other resources that the kernel provides. One such common class of devices that are like this are for industrial I/O cards.

To address this situation, the userspace I/O system (UIO) was designed. For typical industrial I/O cards, only a very small kernel module is needed. The main part of the driver will run in user space. This simplifies development and reduces the risk of serious bugs within a kernel module.

Please note that UIO is not an universal driver interface. Devices that are already handled well by other kernel subsystems (like networking or serial or USB) are no candidates for an UIO driver. Hardware that is ideally suited for an UIO driver fulfills all of the following:

I'd like to thank Thomas Gleixner and Benedikt Spranger of Linutronix, who have not only written most of the UIO code, but also helped greatly writing this HOWTO by giving me all kinds of background information.

Find something wrong with this document? (Or perhaps something right?) I would love to hear from you. Please email me at <hjk@linutronix.de>.

Each UIO device is accessed through a device file and several sysfs attribute files. The device file will be called /dev/uio0 for the first device, and /dev/uio1, /dev/uio2 and so on for subsequent devices.

/dev/uioX is used to access the address space of the card. Just use mmap() to access registers or RAM locations of your card.

Interrupts are handled by reading from /dev/uioX. A blocking read() from /dev/uioX will return as soon as an interrupt occurs. You can also use select() on /dev/uioX to wait for an interrupt. The integer value read from /dev/uioX represents the total interrupt count. You can use this number to figure out if you missed some interrupts.

For some hardware that has more than one interrupt source internally, but not separate IRQ mask and status registers, there might be situations where userspace cannot determine what the interrupt source was if the kernel handler disables them by writing to the chip's IRQ register. In such a case, the kernel has to disable the IRQ completely to leave the chip's register untouched. Now the userspace part can determine the cause of the interrupt, but it cannot re-enable interrupts. Another cornercase is chips where re-enabling interrupts is a read-modify-write operation to a combined IRQ status/acknowledge register. This would be racy if a new interrupt occurred simultaneously.

To address these problems, UIO also implements a write() function. It is normally not used and can be ignored for hardware that has only a single interrupt source or has separate IRQ mask and status registers. If you need it, however, a write to /dev/uioX will call the irqcontrol() function implemented by the driver. You have to write a 32-bit value that is usually either 0 or 1 to disable or enable interrupts. If a driver does not implement irqcontrol(), write() will return with -ENOSYS.

To handle interrupts properly, your custom kernel module can provide its own interrupt handler. It will automatically be called by the built-in handler.

For cards that don't generate interrupts but need to be polled, there is the possibility to set up a timer that triggers the interrupt handler at configurable time intervals. This interrupt simulation is done by calling uio_event_notify() from the timer's event handler.

Each driver provides attributes that are used to read or write variables. These attributes are accessible through sysfs files. A custom kernel driver module can add its own attributes to the device owned by the uio driver, but not added to the UIO device itself at this time. This might change in the future if it would be found to be useful.

The following standard attributes are provided by the UIO framework:

These attributes appear under the /sys/class/uio/uioX directory. Please note that this directory might be a symlink, and not a real directory. Any userspace code that accesses it must be able to handle this.

Each UIO device can make one or more memory regions available for memory mapping. This is necessary because some industrial I/O cards require access to more than one PCI memory region in a driver.

Each mapping has its own directory in sysfs, the first mapping appears as /sys/class/uio/uioX/maps/map0/. Subsequent mappings create directories map1/, map2/, and so on. These directories will only appear if the size of the mapping is not 0.

Each mapX/ directory contains four read-only files that show attributes of the memory:

From userspace, the different mappings are distinguished by adjusting the offset parameter of the mmap() call. To map the memory of mapping N, you have to use N times the page size as your offset:

offset = N * getpagesize();

Sometimes there is hardware with memory-like regions that can not be mapped with the technique described here, but there are still ways to access them from userspace. The most common example are x86 ioports. On x86 systems, userspace can access these ioports using ioperm(), iopl(), inb(), outb(), and similar functions.

Since these ioport regions can not be mapped, they will not appear under /sys/class/uio/uioX/maps/ like the normal memory described above. Without information about the port regions a hardware has to offer, it becomes difficult for the userspace part of the driver to find out which ports belong to which UIO device.

To address this situation, the new directory /sys/class/uio/uioX/portio/ was added. It only exists if the driver wants to pass information about one or more port regions to userspace. If that is the case, subdirectories named port0, port1, and so on, will appear underneath /sys/class/uio/uioX/portio/.

Each portX/ directory contains four read-only files that show name, start, size, and type of the port region:

This structure tells the framework the details of your driver, Some of the members are required, others are optional.

Usually, your device will have one or more memory regions that can be mapped to user space. For each region, you have to set up a struct uio_mem in the mem[] array. Here's a description of the fields of struct uio_mem:

Please do not touch the kobj element of struct uio_mem! It is used by the UIO framework to set up sysfs files for this mapping. Simply leave it alone.

Sometimes, your device can have one or more port regions which can not be mapped to userspace. But if there are other possibilities for userspace to access these ports, it makes sense to make information about the ports available in sysfs. For each region, you have to set up a struct uio_port in the port[] array. Here's a description of the fields of struct uio_port:

Please do not touch the portio element of struct uio_port! It is used internally by the UIO framework to set up sysfs files for this region. Simply leave it alone.

What you need to do in your interrupt handler depends on your hardware and on how you want to handle it. You should try to keep the amount of code in your kernel interrupt handler low. If your hardware requires no action that you have to perform after each interrupt, then your handler can be empty.

If, on the other hand, your hardware needs some action to be performed after each interrupt, then you must do it in your kernel module. Note that you cannot rely on the userspace part of your driver. Your userspace program can terminate at any time, possibly leaving your hardware in a state where proper interrupt handling is still required.

There might also be applications where you want to read data from your hardware at each interrupt and buffer it in a piece of kernel memory you've allocated for that purpose. With this technique you could avoid loss of data if your userspace program misses an interrupt.

A note on shared interrupts: Your driver should support interrupt sharing whenever this is possible. It is possible if and only if your driver can detect whether your hardware has triggered the interrupt or not. This is usually done by looking at an interrupt status register. If your driver sees that the IRQ bit is actually set, it will perform its actions, and the handler returns IRQ_HANDLED. If the driver detects that it was not your hardware that caused the interrupt, it will do nothing and return IRQ_NONE, allowing the kernel to call the next possible interrupt handler.

If you decide not to support shared interrupts, your card won't work in computers with no free interrupts. As this frequently happens on the PC platform, you can save yourself a lot of trouble by supporting interrupt sharing.

In many cases, UIO drivers for platform devices can be handled in a generic way. In the same place where you define your struct platform_device, you simply also implement your interrupt handler and fill your struct uio_info. A pointer to this struct uio_info is then used as platform_data for your platform device.

You also need to set up an array of struct resource containing addresses and sizes of your memory mappings. This information is passed to the driver using the .resource and .num_resources elements of struct platform_device.

You now have to set the .name element of struct platform_device to "uio_pdrv" to use the generic UIO platform device driver. This driver will fill the mem[] array according to the resources given, and register the device.

The advantage of this approach is that you only have to edit a file you need to edit anyway. You do not have to create an extra driver.

Especially in embedded devices, you frequently find chips where the irq pin is tied to its own dedicated interrupt line. In such cases, where you can be really sure the interrupt is not shared, we can take the concept of uio_pdrv one step further and use a generic interrupt handler. That's what uio_pdrv_genirq does.

The setup for this driver is the same as described above for uio_pdrv, except that you do not implement an interrupt handler. The .handler element of struct uio_info must remain NULL. The .irq_flags element must not contain IRQF_SHARED.

You will set the .name element of struct platform_device to "uio_pdrv_genirq" to use this driver.

The generic interrupt handler of uio_pdrv_genirq will simply disable the interrupt line using disable_irq_nosync(). After doing its work, userspace can reenable the interrupt by writing 0x00000001 to the UIO device file. The driver already implements an irq_control() to make this possible, you must not implement your own.

Using uio_pdrv_genirq not only saves a few lines of interrupt handler code. You also do not need to know anything about the chip's internal registers to create the kernel part of the driver. All you need to know is the irq number of the pin the chip is connected to.

Information about all UIO devices is available in sysfs. The first thing you should do in your driver is check name and version to make sure your talking to the right device and that its kernel driver has the version you expect.

You should also make sure that the memory mapping you need exists and has the size you expect.

There is a tool called lsuio that lists UIO devices and their attributes. It is available here:

http://www.osadl.org/projects/downloads/UIO/user/

With lsuio you can quickly check if your kernel module is loaded and which attributes it exports. Have a look at the manpage for details.

The source code of lsuio can serve as an example for getting information about an UIO device. The file uio_helper.c contains a lot of functions you could use in your userspace driver code.

After you made sure you've got the right device with the memory mappings you need, all you have to do is to call mmap() to map the device's memory to userspace.

The parameter offset of the mmap() call has a special meaning for UIO devices: It is used to select which mapping of your device you want to map. To map the memory of mapping N, you have to use N times the page size as your offset:

	offset = N * getpagesize();

N starts from zero, so if you've got only one memory range to map, set offset = 0. A drawback of this technique is that memory is always mapped beginning with its start address.

After you successfully mapped your devices memory, you can access it like an ordinary array. Usually, you will perform some initialization. After that, your hardware starts working and will generate an interrupt as soon as it's finished, has some data available, or needs your attention because an error occured.

/dev/uioX is a read-only file. A read() will always block until an interrupt occurs. There is only one legal value for the count parameter of read(), and that is the size of a signed 32 bit integer (4). Any other value for count causes read() to fail. The signed 32 bit integer read is the interrupt count of your device. If the value is one more than the value you read the last time, everything is OK. If the difference is greater than one, you missed interrupts.

You can also use select() on /dev/uioX.

Since the driver does not declare any device ids, it will not get loaded automatically and will not automatically bind to any devices, you must load it and allocate id to the driver yourself. For example:

 modprobe uio_pci_generic
 echo "8086 10f5" > /sys/bus/pci/drivers/uio_pci_generic/new_id
	

If there already is a hardware specific kernel driver for your device, the generic driver still won't bind to it, in this case if you want to use the generic driver (why would you?) you'll have to manually unbind the hardware specific driver and bind the generic driver, like this:

    echo -n 0000:00:19.0 > /sys/bus/pci/drivers/e1000e/unbind
    echo -n 0000:00:19.0 > /sys/bus/pci/drivers/uio_pci_generic/bind
	

You can verify that the device has been bound to the driver by looking for it in sysfs, for example like the following:

    ls -l /sys/bus/pci/devices/0000:00:19.0/driver
	

Which if successful should print

  .../0000:00:19.0/driver -> ../../../bus/pci/drivers/uio_pci_generic
	

Note that the generic driver will not bind to old PCI 2.2 devices. If binding the device failed, run the following command:

  dmesg
	

and look in the output for failure reasons

Interrupts are handled using the Interrupt Disable bit in the PCI command register and Interrupt Status bit in the PCI status register. All devices compliant to PCI 2.3 (circa 2002) and all compliant PCI Express devices should support these bits. uio_pci_generic detects this support, and won't bind to devices which do not support the Interrupt Disable Bit in the command register.

On each interrupt, uio_pci_generic sets the Interrupt Disable bit. This prevents the device from generating further interrupts until the bit is cleared. The userspace driver should clear this bit before blocking and waiting for more interrupts.

Userspace driver can use pci sysfs interface, or the libpci libray that wraps it, to talk to the device and to re-enable interrupts by writing to the command register.

Here is some sample userspace driver code using uio_pci_generic:

#include <stdlib.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <errno.h>

int main()
{
	int uiofd;
	int configfd;
	int err;
	int i;
	unsigned icount;
	unsigned char command_high;

	uiofd = open("/dev/uio0", O_RDONLY);
	if (uiofd < 0) {
		perror("uio open:");
		return errno;
	}
	configfd = open("/sys/class/uio/uio0/device/config", O_RDWR);
	if (uiofd < 0) {
		perror("config open:");
		return errno;
	}

	/* Read and cache command value */
	err = pread(configfd, &command_high, 1, 5);
	if (err != 1) {
		perror("command config read:");
		return errno;
	}
	command_high &= ~0x4;

	for(i = 0;; ++i) {
		/* Print out a message, for debugging. */
		if (i == 0)
			fprintf(stderr, "Started uio test driver.\n");
		else
			fprintf(stderr, "Interrupts: %d\n", icount);

		/****************************************/
		/* Here we got an interrupt from the
		   device. Do something to it. */
		/****************************************/

		/* Re-enable interrupts. */
		err = pwrite(configfd, &command_high, 1, 5);
		if (err != 1) {
			perror("config write:");
			break;
		}

		/* Wait for next interrupt. */
		err = read(uiofd, &icount, 4);
		if (err != 4) {
			perror("uio read:");
			break;
		}

	}
	return errno;
}